PERRY ELECTRIC Srl 1IT1051 Wall Mounted Timed Switch Stairs Instruction Manual
- May 15, 2024
- PERRY ELECTRIC Srl
Table of Contents
Wall mounted timed switch for stairs
1IT1051
SAFETY WARNINGS
Read this installation and use manual carefully The manual must be preserved
with care for future reference..
The manufacturer reserves the right to introduce any technical and/or
constructive changes deemed necessary, with no prior notice.
Important: installation and electrical connections of devices and appliances
must be carried out by skilled people and in compliance with current
regulations.
The manufacturer declines any liability in connection with the use of products
subject to special environmental and/or installation standards.
Make sure the 230V mains power supply is disconnected before installing or
carrying out any maintenance operations.
Cleaning: once installed, the device requires no maintenance. Any special
work after installation must be done by qualified personnel.
Use a slightly damp cloth for cleaning (do not use detergents).
DISPOSING OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on the product or on its packaging indicates that this product
cannot be treated as household waste. On the contrary, it must be taken to a
specific collection centre for recycling electrical and electronic equipment,
such as:
– outlets, if a similar product to the one being disposed of is being
purchased
– local collection centres (waste collection centres, local recycling centres,
etc.).
By making sure the product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which
could otherwise be caused by inadequate disposal of this product. Recycling
materials will help conserve natural resources. For more detailed information
about recycling this product, please contact the local office in your area,
the household waste disposal service in your area or the shop where you
purchased this product.
TECHNICAL DATA
Supply | 230V a.c. ± 10% 50-60Hz |
---|---|
Type disconnect and device: | 1 BU/Electronic |
Mounting type (fixed) | su quadro, Wall mounting |
Output on relay contacts NO/COM/NC | 16(3)A 250V c.a. |
Maximum controllable power | 3300W (cos,o = 1) |
Timer adjustable from | 30″ / 4 7′ |
Resettable | Si |
Possibility to operate with max | 30 luminous push-buttons |
Min. resistive load acceptable | 10 W |
Possibility to pilot neon lamps | minimum 40 W |
Possibility to pilot electronic lamps | minimum 16 W |
3 wire connection | |
Fixed light switch | |
Maximum wire section at terminals | 2,5 mm2 |
Pollution degree | IP20 |
Pollution degree | 2 |
Type of insulation | Class II |
CE marking regulation | EMC EM55104 |
LVD EN607301 EM60730-2-7
IMPORTANT!
The working of the timed switch is subordinated to the presence of at least 1
push-button with luminous indicator. If there are no luminous push-buttons in
the installation, it is necessary to substitute at least 1 push-button with a
luminous one or to connect the 100 K resistance (supplied with he product) in
parallel toΩ whatever push-button. NOTE FOR INSTALLER:
In the case of fixed wall-mounted installation, provide adequate wiring ducts
in compliance with the current plant standards.
In particular, any round duct (Ø min. 16 mm) must enter the outer shell
through a suitable inlet hole, which does not reduce the declared IP20 degree.
ANNOTATION:
Product built with excellent electronic technology, it is suitable as a single
electronic timed switch, perfectly replaceable without any system modication
to three-wire electromechanical models made in Germany, Spain, etc.
Three-wire connection scheme.
ELECTRIC CONNECTION The working of the timed switch is subordinated to the
connection to a minimum load (neon 40 W, electronic 16 W, incandescent 10 W)
because, .in absence of load the product doesn’t work When the connections are
connected on the timer terminal board, the set time (from 30 “÷ 7 ‘) will be
automatically loaded.
After the first cycle the insertion will take place by pressing the command
buttons.
The manufacturer reserves the right to make all technical and manufacturing
modifications deemed necessary without prior notice.
PERRY ELECTRIC Srl
Via Milanese, 11
22070 VENIANO (CO)
ITALY www.perry.it