Neodrain ZS3 Square Shower Drain Instruction Manual
- May 15, 2024
- Neodrain
Table of Contents
Neodrain ZS3 Square Shower Drain
Important Information
Carefully read the following instructions before proceeding with the installation, the warranty will be void if the product is installed with a conspicuous defect.
- Thoroughly inspect all components before starting the installation. If you find any items be damaged or lacked, please contact us at soonest possible, your questions will be responded within 12 hours.
- Our stainless steel product does not rust, but external factors such as sealant, adhesive, mortar or any aggressive substance may have “surface” rust on the channel body. After installation, recommend to remove such “rust” using a scour pad, always brushing in the direction of the gain.
- Our drain and grate can be cleaned and maintained using a non-abrasive stainless steel cleaner or soft scrub. For Polished Stainless, we recommend a mid soap and a soft cloth for cleaning. All cleaning agents must be free of hydrochloric and hydrofluoric acid.
Components list of grating style
*This item is not essential for every installation manner.
- Shower drain grate
- Stainless strainer
- Drain Body
- Threaded adaptor*
- Grate and strainer hook
Components list of tile-in style
- Tile-insert tray 1
- Stainless strainer
- Drain Body
- Threaded adaptor 2
- Grate and strainer hook
- Tray supporter ( PA)
- Recessed to hold tile and thin set to 0. 5 // ( 12. 7mm) thick. Apply tile adhesive or thin set to secure the tile inside the tray.
- This item is not essential for every installation manner.
Placement in Bathroom
Using a single square drain in the shower area, floors must be graded
appropriately or other barriers must be used to prevent flow of water into
bathroom area.
If the square drain will be set in a spot without underneath access, such as
in a concrete floor or an upper floor with a finished ceiling that won’t be
opened, then the drain will need to roughed-in before setting the unit in
place.
The following installation steps are applicable for concrete substrate only.
Instruction For Use
-
Disassemble the drain coupling, install the base to the waste pipe and secure it in place.
If use PVC pipe, glue with PVC cement. If use No-Hub rubber coupling, fasten with screwdriver.
Always consult with a licensed professional during installation. -
Stuff a rag into the drain opening. Apply floor mortar to build up the shower pan liner, the surface should be slope of 1°,opprox 1/4″ per foot toward the drain. Allow the mortar to cure 12 hours.
-
Press the waterproof membrane down around the bolts, use utility knife to cut a slit for the bolts to poke through, afterwords cut away the waste hole in the center.
Always consult with a licensed professional during installation. -
Partially loose the drain bolts, install the coupling plate, tightening them evenly and firmly to create watertight seal once the membrane installed.
-
Insert drain body into waste hole, adjust the height to be compatible with planned floor, make sure the height from the top edge to the coupling plate not less than 1- 1I 2″ .
Always consult with a licensed professional during installation. -
Apply floor mortar to build up the second mortar bed, the surface most have minimum drainage slope of l 0 , approximately 1 / 4”’ per foot toward the drain. Leaving space of tile thickness and thin set along the seam.
-
After the second mortar bed cured for 12 hours, install the floor tile with thin set or tile adhesive.
Always consult with a licensed professional during installation. -
Fill the gap around the drain body with silicone bead or grout. Take away the dust cloth, finalize the installation by laying the strainer and grating.
Note: Wait for 24 hours before using your shower.
INSTALLATION DIAGRAM -Standard Clamp Drain
Note 1 Building paper should be stapled to the plywood floor before being
covered with a galvanized metal mesh.
Note 2 Mortar bed 2 plus tile and adhesive should be no less than 1-1
/2″(40mm)
Note 3 PVC drain base and waterproof membrane should be purchased
separately·
Code approval per ASME A 112.18-2/CSA Bl 25.2.05 (US and Canada)
Customers Support
Support@neodrain.com
Neodrain Technologies CO.,LTD
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>