FiberHome HG6245Y GPON Optical Network Unit User Manual

FiberHome HG6245Y GPON Optical Network Unit User Manual

Operation Safety Rules

For a correct, safe use of the equipment, please read the following carefully and strictly observe the operation safety rules during your operations.

• High optical power can cause bodily harm, especially to eyes. Never look directl y into the end of the optical transmitter fiber jumper or the end of its active connector.

• Exercise care if you must bend fibers. If bends are necessary, the fiber bending radius should never be less than 38mm.

• Power socket overload, broken cables or broken plugs may cause electric shock or fire.
  Regular check-ups on power supply wires and cables are essential. If any appears damaged, replace at once.

• Use the power supply adapter provided in the package only. Using other adapters may cause equipment damage or operation failures.

• Install the equipment in a well ventilated environment without high temperatures or direct sun light to protect the equipment and its components from overheating, which can resuIt in damage.

• Power off the equipment in the event of lightning storms. Disconnect all cables connected to the equipment such as power cable, network cable and telephone line to avoid equipment damages caused by lightning stroke.

• Avoid moisture, dampness and water damage. Equipment exposed to water cannot work normally and can be extremely hazardous due to shooting.

• Do not lay this equipment on an unsteady base.

• 5.15-5.25 frequency band used indoor only.

Product Introduction

The HG6245Y is an FTTH GPON optical network unit. It provides communication and entertainment service in multiple modes such as data, voice and video, to meet integrated access requirement of families or small enterprises. The HG6245Y supports these functions:

• Uses GPON uplink that is compliant with ITU-T G.984 series of standards;
• Supports the configuration of Ethernet interface rates, working modes, MDI / MDIX autonegotiation mode;
• Supports packet filtering and DoS attack protection;
• Provides performance statistics on all Ethernet lines;
• Supports obtaining the user IP address in the DHCP mode, supports reporting the physical position information of Ethernet interfaces through DHCP Option82;
• Supports obtaining the user IP address in the PPPoE mode,
• supports the PPPoE+ function for accurate user identification;
• Supports various voice protocols including H.248 and SIP;
• Supports IGMP snooping protocol;
• Supports the L2 / L3 wire speed forwarding;
• Supports the AES-128 algorithm for encryption of downlink data;
• Supports global configuration of queue priorities and flexible 802.1p-to-queue mapping;
• Supports the PQ queue scheduling mode. You can configure the weight of scheduling queue to ensure the QoS of the services with high QoS requirement such as voice and video under multiple service conditions;
• Supports wireless access mode, compliant with the IEEE 802.11 a/b/g/n/ac/ax stand ard;
• Supports the authentication modes such as OPEN, SHARE D, WPA- PSK, WPA2-PSK, WPAPSK/WPA2-PSK. WPA3 -SAE. WPA2 – PSK/WPA3 -SAE. Supports the encryption modes such as NONE, WEP, TKIP, AES, and TKIP/AES.

Product Type

HG6245Y

4 GE interfaces
2 phone interfaces
Wi- Fi interface

Internal antenna

Technical Specification

Power consumption

parameter

| Power consumption| <20W

Environmental parameter

| Operating temperature| -5°C to 45°C
Storage temperature| -40°C to 70°C
Environmental humidity| 10% to 90%, non-condensing

Equipment Installation

The HG6245Y can be placed verticalIy on a desk.

Vertical desktop mounting

The picture only for you reference!

Interfaces and Connections

Rear panel

1. Phone interface
2. Ethernet interface
3. USB interface
4. WLAN switch
5. WPS switch
6. Reset button
7. Power interface
8. Power switch

Indicator LED Description

equipment is not powered on.
2 Registration status LED (green)| The ONU is activated.| The ONU is activating.| The ONU is not activated.
3 Optical signal status LED (red)| ___| No optical signals are received.| Optical signals are received.
4 Internet status LED(green)| The access to Internet is normal.| The access to Internet is normal with data trans-mission.| No access to Internet.
5 USB status LED (green)| The USB is connected.| ___| The USB is not connected.
6 Ethernet interface status LED (green)| The interface is connected to the subscriber terminal without data transmission.| The interface is receiving / transmitting data.| The interface is not connected to the subscriber terminal.
7 Wi-Fi signal status LED (green)| The interface is enabled.| The interface has traffic.| The interface is disabled.
8 WPS status LED (green)| The WPS is enabled and connected.| The related negotiation is conducted via WPS.| The WPS is not enabled or connected.
9 Phone interface status LED (green)| The interface registration to the softswitch platform is successful.| The interface has traffic.| The interface registration to the softswitch platform failed.

Note:
Reset key: Press the button for more than 5 seconds to restore the default settings and reboot the device.

Logging into Web Configuration GUI

Step 1 Set the IP address and subnet mask of the computer.

• Select the Obtain an IP address automatically mode (recommended).
• Set to a static IP address in the same network segment of the management IP address (192.168.1.1 by default) of the HG6245Y.
  • IP address: 192.168.1.X (X is a decimal integer between 2 and 254)
  • Subnet mask: 255.255.255.0

Step 2 Enter http://192.168.1.1/normal in your browser’s address bar. Press Enter to bring up the user login dialog box.

Step 3 Enter username and password (see the label at the bottom of the device for the default settings) in the login dialog box. Access the Web page after the password is authenticated successfully.

Note: If no operation is performed in five minutes after login, the system will log out.

Enabling the Wireless Access Function

Step1 Select Network in the navigation bar and select WLAN Settings—>2.4G Basic or WLAN Settings —>5G Basic in the link bar to open the page for the basic wireless configuration of the 2.4G or 5G Wi-Fi interface.

Step2 Make sure the button next to Radio On/Off is On and keep the default settings for other parameters, for example:

• Network Mode: 802.11 ax (2.4G Wi-Fi) or 802.11 ax (5G Wi-Fi)
• Frequency (Channel): AutoSelect
• Frequency Bandwidth: 20MHz/40MHz (2.4G Wi-Fi) or 80MHz (5G Wi-Fi)

Step3 Click Apply and save the configured information.

Note:

• On the Wi-Fi terminal, users can use the default SSID name and password (see the label at the bottom of the device) to connect with the wireless network.
• To modify the parameters such as SSID name, password and authentication & encryption mode, refer to “Setting Wireless Network”.
• If the selected frequency band cannot be connected, it may be used by an AP device around. Try another band for connection.

Setting Wireless Network

Step 1 Select Network in the navigation bar and select WLAN Settings—>2.4G Advanced or WLAN Settings —)5G Advanced in the link bar to open the page for the advanced wireless configuration of the 2.4G or 5G Wi-Fi interface.

Step 2 Set the parameters of the wireless network, including SSID name, password and authentication and encryption mode.

• SSID choice: Click the drop-down list to select the SSID. The default settings for 2.4G and 5G Wi-Fi are Enable.
• SSID Name: Enter the wireless network name for the Wi-Fi terminal to search. It is advisable to use a name easy to identify.
• Security Mode: It is advisable to select the default security mode such as WPA-PSK/WPA2- PSK.
• WPAAlgorithms: It is advisable to select the default encryption mode such as TKIP/AES.
• Pass Phrase: Enter the password for the Wi-Fi terminal to access the wireless network. It is advisable to use a complex password to guarantee the security of wireless network.
• Key Renewal Interval: It is advisable to use the default value.

Step 3 Click Apply and save the currently configured SSID information.

Note:

•  If the SSID name and password corresponding to the default 2.4G or 5G SSID choice are modified, the default wireless network account (2.4G or 5G) will become invalid.
• If they forget the customized SSID name and password, users can log into the Web to query the information or restore the default wireless network account.
• After the device is connected with WLAN successfully, users can select Hidden in the SSID Name bar to hide the network.

User Management

Step 1 Select Management in the navigation bar. Click Account Management- User Account in the link bar to open the account maintenance page.
Step 2 Enter the username.
Step 3 Enter the old password.
Step 4 Enter the new password.
Step 5 Re-enter the new password to confirm that the passwords entered are identical. Step 6 Click Apply to save and apply the new password settings.

Rebooting the Equipment

Step 1 Select Management in the navigation bar. Click Device Management— Device Reboot in the link bar to open the device rebooting page. Step 2 Click Reboot and click Yes in the dialog box that appears to reboot the equipment.
Note: Reboot the device, and wait about 2 minutes before re-logging into the Web configuration GUI.

FAQs

FAQ1: All indicator LEDs are extinguished after power-on.

1. Check whether the power cable is correctly connected;
2. Check whether the power supply and the power adapter are normal;
3. Check whether the power switch on the device’s rear panel is in the ON position.

FAQ2: The device fails to work.

1. If the device works abnormally, check whether the power is connected normally or the voltage is not within specifications;
2. If the equipment is overheated, check the ventilation. Make sure the equipment is not exposed to direct sunshine or is near the heat source.

FAQ3: The LOS Indicator LED blinks.

1. Check whether the optical fiber is damaged;
2. Check whether the optical fiber is connected normally to the appropriate interlace;
3. Check whether the received optical power of the ONU is below specifications with an optical power meter;
4. Check whether the ONU optical module is aged or damaged;
5. Check whether the device at the central office end is operating normally.

FAQ4: The LAN Indicator LED Is extinguished.

1. Check whether the network cable is damaged or incorrectly connected;
2. Check whether the wiring color-coding scheme of the network cable is incorrect. If incorrect, replace the original network cable with a standard CAT-5 twisted-pair network cable;
3. Check whether the network cable crosses the allowed range.

FAQ5: The ONU cannot be visited via WI-Fl.

1. Check whether the Wi-Fi function for the ONU is enabled, and whether the SSID is set to Hidden so that the Wi-Fi signal cannot be detected.
2. Check whether the network card driver is normally installed on the computer and whether the WLAN function for the wireless terminals like computers or mobile phones is enabled.
3. Adjust the location of the ONU. so as to reduce obstacles such as walls on the path of the signal. The distance between the ONU and the wireless terminals should be within the required range.

FAQ6: Logging into the Web page failed.

1. Check the network card configuration, browser version of the user’s computer:
2. Check whether the IP address of the user’s computer is correctly configured.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the followi-g two conditions: (1) this device may not cause harmful interference. and (2) this device mist accept any interference received. includeg interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment

NOTE: This equipment has been tested and found to comply with the limits for a Class 8 digital device. pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio TV technician for help important announcement

Important Nate: Radiation Exposure Statement This equipment complies with FCC radiation expcsure knits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating n conjunction with any other antenna or transmitter.

Warranty Card

We appreciate your purchase of FiberHome product. FiberHome warrants that the equipment will be free of defects in materials and workmanship for a period of 12 months from the date of purchase. The original, dated, bill of sale should be retained as proof of purchase and must be presented to FiberHome when the equipment is to be serviced under the provisions of this warranty.

Customer Name|
---|---
Address / Zip Code|
Phone|
E-mail|
Model Number|
Serial Number|
Date of Purchase|
Invoice Number|
Dealer Name|
Dealer Address|
Dealer Phone|

Please keep this card properly. No reissuance if lost.

Dealer: (Seal)

Warranty Description

When you purchase a product offered by FiberHome from an authorized dealer, you have a 12-month warranty as standa rd, except for man-made causes. The wa rranty period begins on the date of invoice.

For your lawful rights and interests, please notice:

1. The Warranty Card shall come into force with the seal of dealer.
2. Please keep this card properly. No reissuance will be provided if you lose it and it becomes invalid if altered.
3. In the event of a non man-made malfunction during the warranty period, FiberHome will repair or replace this product to its original operating condition free of charge.

Warranty does not cover the following circumstances:

1. Damage or malfunction caused by transporting, loading and unloading.
2. Damage or malfunction caused by man-made reasons such as opening or remodel the machine on users’ own.
3. Damage or malfunction caused by unsatisfactory environment.
4. Damage or malfunction caused by force majeure incidents (such as fire, earthquake, lightning strike, war).
5. Damage or malfunction caused by failure to operate and maintain in accordance with the user’s manual.
6. Damage of external parts such as equipment enclosure, power connector in operation.
7. The inconsistence of the Warranty Card and the product serial number, or the warranty card has been altered.

We provide paid repair and maintenance service for the products that a re beyond the wa rranty scope. The final explanation rights of this warranty description are reserved by FiberHome.

are trademarks of FiberHome Telecommunication Technologies Co., Ltd.
(Hereinafter referred to as FiberHome).
All brand names and product names used in this document are used for identification purposes only and are trademarks or registered trademarks of their respective holders.
No part of this document (including the electronic version) may be reproduced or transmitted in any form or by any means without prior written permission from FiberHome.

Information in this document is subject to change without notice.

2020 FiberHome Telecommunication Technologies Co., Ltd.
All rights reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>