SR SUN RISE SR-2 Shower Faucet Set Shower Valve with 8 Inch Rainfall Shower Head and Handheld Shower Instruction Manual

SR SUN RISE SR-2 Shower Faucet Set Shower Valve with 8 Inch Rainfall

Shower Head and Handheld Shower

Please do not hesitate to contact us with your questions, concerns and/or problems, we’re here to help. We will replace or repair your product free of charge.

IAPMO RESEARCH AND TESTING, INC.
5001 E. Philadelphia Street, Ontario, CA 91761 • Phone 909-472-4100 • Fax 909-472-4244 • www.iapmort.org.

CERTIFICATE OF LISTING
IAPMO Research and Testing, Inc. is a product certification body that tests and inspects samples taken from the supplier’s stock or the market or a combination of both to verify compliance to the requirements of applicable codes and standards. This activity is coupled with periodic surveillance of the supplier’s factory and warehouses as well as the assessment of the supplier’s Quality Assurance System. This listing is subject to the conditions outlined in the characteristics below and is not to be construed as any recommendation, assurance or guarantee by lAPMO Research and Testing, Inc. of the product acceptance by Authorities Having Jurisdiction.

GUANGDONG RI ZHENG INDUSTRIAL CO., LTD.
NO.41 XIANSAN ROAD, RIZHENG BUILDING, WANJIANG SREET, 52300 DONGGUAN, GUANGDONG, CHINA Product:
Plumbing Fixture Fittings

*This certificate is not evidence of the current listing. To verify listing status, visit the IAPMO R&T Product Listing Directory at pid.japmo.org This listing period is based upon the last date of the month indicated on the Effective Date and Void After Date shown above. Any change in material, manufacturing process, marking or design without having first obtained the approval of the Product Certification Committee, or any evidence of non-compliance with applicable codes and standards or of inferior workmanship, may be deemed sufficient cause for revocation of this listing. Production of or reference to this form for advertising purposes may be made only by specific written permission of lAPMO Research and Testing, Inc. Any alteration of this certificate could be grounds for revocation of the listing. This document shall be reproduced in its entirety.

• Issued To: GUANGDONG RI ZHENG INDUSTRIAL CO., LTD.
• File Number: 12900
• Product: Plumbing Fixture Fittings
• Effective Date: January 2021
• Revised Date: January 28, 2021
• Void After: January 2026

This certificate is not evidence of the current listing. To verify listing status, visit the APMO R&T Product Listing Directory at pid.iapmo.org

Identification

• Plumbing supply fittings shall be marked with the manufacturer’s recognized name, trademark, or other mark or, in the case of private labelling, the name, trademark or another mark of the customer for whom the fitting was manufactured. The marking shall be accomplished by use of a permanent mark or by placing a permanent label on the product. Markings on plumbing supply fittings shall be visible after installation.
• Showerheads and hand-held showers shall be marked with the manufacturer’s specified maximum flow rate, in L/min and gpm.
• Kitchen, lavatory, and metering faucets shall be marked with the manufacturer’s specified maximum flow rate, in L/min and gpm or L/cycle and gpc.
• Single-handle and single-control bath and shower mixing valves shall have their temperature control settings identified alphabetically, numerically, or graphically.
• High-efficiency commercial pre-rinse spray valves shall be marked with the manufacturer’s specified maximum flow rate, in Limin (gpm).
• Listed products shall bear the cUPC® certification mark.
• Packaging for plumbing supply fittings shall be marked with the manufacturer’s name, trademark, or other mark as well as the model number or, in the case of private labelling, the name, trademark, or mark of the customer for whom the fitting was manufactured as well as the model number.
• Packaging for showerheads and hand-held showers shall be marked with the manufacturer’s specified maximum flow rate and either the manufacturer’s specified minimum flow rate or the statement “For use with automatic compensating valves rated at xxx
• L/min (my gpm) or less”, where xxx L/min (my gpm) is the manufacturer’s specified minimum flow rate.
• Packaging for kitchen, lavatory, and metering faucets shall be marked with the manufacturer’s specified maximum flow rate, in L/min and gpm or L/cycle and gpc.

Characteristics

• Fittings may include lavatory, sink, bath & shower, lawn and sediment faucets. Plumbing fixture fittings to be installed under the manufacturer’s instructions and the requirements of the latest edition of the Uniform Plumbing Code and National Plumbing Code of Canada.
• Products listed on this certificate have been tested by an lAPMO R&T-recognized laboratory. This recognition has been granted based on the laboratory’s compliance to the applicable requirements of ISO/EC 17025.

Package list

WARNING: Choking hazard. Please keep all small parts and plastic bags out of the reach of children.

INSTALL SHOWER VALVE

Step 1: Measure valve installation dimensions.

Step 2: Determine the position of the valve.

Step 3: Drill, hammer in anchors, and fasten valve body to the wall(This step is for masonry application.)

Step 4: Check for level on the valve body.

Step 5: Connect the water pipe. (Pipe clean and free of impurities)
Be suitable for Pex pipe, Copper pipe and PVC pipe

• 1/2 inch male NPT fitting connection to be made with pipe thread sealant, do not over-tighten.

Step 6: Test for Leaks Before Installing Wall Board

1. Check the valve connector for leaks;
2. Open the valve and test the hot and cold water left and right;
3. Checking the Water diverter knob can correctly switch between the showerhead and handheld.

Step 7: Tile

Important Note

Wall Mounted Installation Before Tiling

• After tiling, the distance from the tile surface to the brass fittings (recessed the wall) is I: The shower bracket (and bathtub faucet) is 0.4 inches. 2: The shower arm is 0.2 inches.

INSTALL SHOWER BRACKET

INSATLL HANDHELD SHOWER HEAD AND SHOWER HOSE.

INSTALL SHOWER ARM AND RAIN SHOWER HEAD

WARRANTY

1. If the above contents are not complete, the warranty will be considered void, please confirm the above contents when you purchase.
2. The complimentary repairs are limited to instances mentioned on the warranty card only.
3. Within the warranty period, if any technical faults occur, the customer should present this warranty card along with the invoice to the retailer/assembly fitter.

Guarantee Repairs Claims

1. Within the warranty period, SR SUNRISE SANITARY is responsible for repairing any defective product free of charge.
2. Please contact the seller via email with this warranty card and invoice if repairs are needed during the warranty period.
3. SR SUNRISE SANITARY will not be responsible for any claims listed below:
   • The damage and/or malfunction caused by improper use and/or repairs; or any unauthorized reconstruction; including any damage caused by abuse (i.e. fall, throw… etc.)
   • Please engage the services of a professional plumber. SR SUNRISE SANITARY will not be responsible for any damage and/or malfunction caused by wrongful installation.
   • The damage and/or malfunction caused by removing after installation or other factors.
   • The damage and/or malfunction caused by application beyond the scope of usage.
   • The damage and/or malfunction caused by sand, dirt and other impurities.
   • The damage and/or malfunction caused by improper/insufficient maintenance; rust on finishing etc…
   • The damage and/or malfunction caused by fir, earthquakes, floods, lightning and other natural disasters, pollution, harmful gas, salts, abnormal voltage and other factors.
   • On occasions when the warranty card or invoice is not presented.
4. The recommended water temperature of the hand shower and rain shower is <42°C; the water pressure is 0.1-0.3 Mpa. The highest temperature should not reach beyond 70°C and water pressure should not exceed the limits of 0.05-0.5 Mpa. Please keep any shower products away from the heating devices to avoid potential risks.
5. This limited warranty applies only to the original end-user or business. It expressly excludes labour charges, removal charges, installation, or other incidental or consequential costs. Any inappropriate application will void the warranty.
6. This warranty cannot be replaced if missed, please keep safe.

Clean and maintain product

How to clean shower head nozzles

1. Just rub the nozzles with your finger or a toothbrush to loosen any deposits, and then run hot water for a few minutes
2. Put the showerhead into a pot. Consider using a smaller container that just about fits the showerhead; this way, you will use less vinegar. You can also use a small bucket or plastic bin.

• Fill the pot with enough white vinegar to cover the showerhead.
• The acids in the vinegar will help dissolve the white mineral deposits on the showerhead.
• Let the showerhead soak in the vinegar for 30 minutes The more soiled the showerhead is, the longer you will have to leave it in the vinegar.

Maintain Chrome and Brushed nickel finished product

1. To clean the products all you need is a high-quality microfiber cloth.
2. Apply a high-quality chrome cleaner to a clean cotton cloth, and wipe over the chrome. Leave as per product instructions, and then rinse with warm water. Gently remove any product residue using a dry chamois or paper towel.
3. How to Clean Chrome: Homemade Solutions In addition to professional products, homespun solutions also have their place when breathing new life into dull chrome. Try this shortcut to achieving chrome cleaning nirvana:

Detergent and warm water! Submerge chrome-plated objects including pots and pans in a sink full of warm water. Add a half-cup of a high-quality washing-up detergent (Persil washing-up liquid is good) and rub gently with a soft cotton cloth to avoid scratching the chrome. Use a scented detergent to leave kitchenware smelling fresh, as well as spotless.

CONTACT

• 5001 E. Philadelphia Street, Ontario, CA 91761
• Phone 909-472-4100
• Fax 909-472-4244
• www.iapmort.org.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>