Ihomeangel A04482 Wall Light Instruction Manual
- June 4, 2024
- Ihomeangel
Table of Contents
A04482 Wall Light
Instruction Manual
Item Number: A04482
WARNING (To reduce the risk of fire, electric shock, or personal injury):
-
We suggest installation by a licensed electrician.
-
Please read the instruction carefully and save them as you may need them at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides.
Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required. -
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
-
Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
-
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
-
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
-
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS INCLUDING:
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Backplate (1)
(F) Knob nut (2)
(G) Arm (1)
(H) Socket (3)
(I) Glass shade (3)
(J) Socket ring (3)
ACCESSORIES ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. -
Make assembly
Step A1: Unscrew knob nuts (F) from the back plate (E), then set them
aside for later installation.
Step A2: Carefully pass the supply wires from the outlet box through the
mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3: Make wire connections Connect wires as the below wires
connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER
CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Connect Black or
Red Supply Wire to:| Connect
White Supply Wire to:
---|---
Black| White
Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
Clear, Brown, Gold, or Black without tracer| Clear, Brown, Gold, or Black with
tracer
Insulated wire ( other than green ) with copper conductor| Insulated wire (
other than green ) with silver conductor
*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.)|
Twist wires together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in the back plate (E) with the preassembled mounting
screws, then attach the back plate (E) to the mounting plate (D) with the
previously removed knob nuts (F). Hand tightens until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of preassembled
mounting screws on mounting plate assembly (D) by unscrewing the pre
assembled hex nuts and then screwing the preassembled mounting screws in or
out of mounting plate (D) until the secure length is achieved.
Tighten the preassembled hex nuts and back to Step A4.
Step A5: 1) Unscrew socket rings (J) from sockets (H).
Place glass shades (I) on sockets (H) and secure them with socket rings (J).
2) Install bulbs (Not included) (Please do not exceed the maximum wattage
recommended on the socket.)
4. Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
+1 850 296 2377
Working hours: Mon Fri 9:00 a.m. 16:00 p.m. EST
homecustomercare@outlook.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>