KETELES K800 Mountain Electric Bike User Manual

: June 17, 2024
: KETELES

Table of Contents

KETELES K800 Mountain Electric Bike
Assembly Instructions
FAQS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

KETELES K800 Mountain Electric Bike

KETELES-K800-Mountain-Electric-Bike-PRODUCT

ATTENTION

Please read this manual carefully before using the lancelets elec-tric bicycle.
If you do not understand this information, or if you do not cover the issues covered in this manual, please contact the dealer.
FULLY CHARGE BATTERIES BEFORE FIRST USE- Batteries should be fully charged immediately when they are received and immediately after each use for the recommended charge times (see below) LI-Ion (Lithium Ion) batteries 4-6 hours (2-3 hours for Via Urbano)
We recommend that you consult a bicycle specialist if you have doubts or concerns as to your experience or ability to properly assemble, repair, or maintain your bicycle.
Additional warning/cautions are in the assembly section of this manual
With proper care and maintenance, your Currie Technologies@ Hybrid Electric Bicycle will provide ease of use and be fun to ride.
Below are points that will help you to maximize the enjoyment you get from your new hybrid electric bicycle

FACTORS TO MAXIMIZE THE RANGE OF YOUR HYBRID ELECTRIC BICYCLE

Ride R input – the more the rider pedals the further the distance traveled. Continuous riding, as opposed to frequent stopping and starting. will yield the greatest range of possible
elevation gain – the flatter the road the further the distance traveled
Weather R- cold weather can adversely affect the battery capacity
Wind – traveling with a tailwind will increase the distance traveled, traveling into a headwind will decrease the distance traveled
Terrain – the smoother the terrain (roadways vs. fireroads, etc.) the further the distance traveled
Ride R WeiGht -the lighter the rider, resulting in less drain on the batteries, the further distance traveled
Bicycle Maintenance- a properly maintained bicycle will yield the greatest range possible
tiRe pRessuRe – properly inflated tires have less rolling resistance and will be easier to pedal
Batteries- properly charged and maintained batteries will yield the greatest range possible. Batteries stored in cold areas (below 50 degrees Fahrenheit/ 10 degrees Celsius) will show a reduced range.
Batteries that have not been kept in optimum condition will show reduced range and run time.

HELMETS SAVE LIVES

ALWAYS WEAR A PROPERLY FITTED HELMET WHEN YOU RIDE YOUR BICYCLE.
DO NOT RIDE AT NIGHT.
CPSC RECORDS SHOW THAT ABOUT 35% OF BICYCLE-RELATED DEATHS OCCUR AFTER DARK.
AVOID RIDING IN WET CONDITIONS.
CPSC RECORDS SHOW THAT ABOUT 65% OF INIURIES HAPPEN TO CHILDREN UNDER 15 YEARS OF AGE.
RIDE ONLY WITH ADULT SUPERVISION
CORRE CTFITT- MAKE SURE YOUR HELME” COVERS’OURFOREHEAD.
INCORRECT FITTING. THE FOREHEAD IS EXPOSED AND VULNERABLE TO SERIOUS INJURY.

Assembly Instructions

The Carton of the E-bike.
Open the Carton
Take the bike and accessories out
Remove the packing EPE pearl cotton
Turn the stem forward. Do not turn the whole fork.
The fork brace should be facing forward.
Remove the 4 bolts
Fit the stem and handlebar together
Tighten the 4 bolts that hold the handlebar
Tighten the bolts on the other side
Handlebar installation completed
The Seat Post Clamp
Open the lever and turn the nut to the loose seat post clamp
Insert the seat post into the seat tube.
Lock the clamp lever tightly
Saddle installation completed
Turn the bike upside down
The fork spacer and brake caliper spacer
Remove the fork spacer. ( it is not a part of the bike )
Put the front wheel on the fork.
The axle of the motor goes into the grooves of the fork.
Put the washers in the right places.
Tighten the nuts on both sides
Connect the inline connectors of the front motor cable
Front-wheel installation completed
The pedal with the letter L should be fixed on the left
Turn the spanner counter-clockwise to fix the pedal L
The pedal with the letter R should be fixed on the right
Turn the spanner clockwise to fix the pedal R
Fix Headlight and fender to the fork brace
Fix rear fender and rear rack to the frame
Tighten the two upper bolts on both sides
Tighten the two lower bolts on both sides
Fenders and Rear Rack installation completed
Ready to install the battery
Push the battery downward and lock it
Assembly job completed
Side view of the completed e-bike
The charging port and the battery ON-OFF switch
Turn on the battery first and then press this button for 3 seconds to turn on the display
The Red switch can turn on or turn off the front motor
Pressing the button + or – can change the speed grade.
The multifunctional color LCD

FAQS

Question 1: What does the display error code mean? What is the reason for it?

Answer: Except for communication errors which are actively reported by the display, all other error codes on the display are reported to the display by the controller, and the display shows them.
The communication error is because the display cannot detect a controller data reply within 10 seconds, Possible reasons:
The communication wire harness between the display and controller is not connected correctly or the wire harness is broken ;
The protocol between the controller and the display does not match ;
The communication wire of the display is burned;
Possible reasons for Hall sensor failure: ① The motor Hall sensor is damaged; ② The Hall sensor wire is connected incorrectly or not properly;
Possible causes of throttle failure: ① The throttle is not in place; ② The throttle is not connected properly; ③ The throttle is damaged;
The motor phase position loss. Possible reasons: ① The motor phase position wire is not connected properly or correctly; ② The motor phase position wire is short-circuited;
Possible reasons for brake failure: ① Brake is not in place ② Brake is damaged or not connected.
A possible reason for controller failure: the controller is damaged or MOS failure.
The possible reason for the abnormal current: the controller is damaged or MOS failure.

YL-01 , YL-02 error code

failure

The power-assisted mode matches with the gear shift to achieve the riding experience of labor-saving and power-saving.
In the setting of power assist riding, on few slopes and good road conditions, it is recommended to match with variable gears, 7-6 high-speed gears, with the best power-saving effect and speed ratio.
In case of large slope road conditions, gear 4-7 is adopted, which can easily and effortlessly climb the slope.
Riding with power-assisted mode, if using speed shifting & climbing mode on flat road will waste electric power and be accompanied by the feeling of empty treading.

5 PAS Grades	Labor power	Motor power	Effect
PASO	100%	0	Cycling for exercise
PAS 1 – PAS2	70%-80%	20%-30%	A slight power assist makes exercise easier
PAS3	50%	50%	Use power assist to ride faster and farther
PAS4- PAS5	20%-30%	70%-80%	Fast cycling, labor-saving

Maintenance and use skills of electric bicycle

The maintenance methods of electric bicycles under different use conditions mainly include the following points.

Influence of temperature.

Temperature has an impact on the use of lithium batteries. Generally speaking, the impact on the use of lithium batteries at room temperature is not significant, but when the temperature is higher than 40 ° C or lower than – 1 O ° C, the discharge capacity of lithium batteries will change.
For example, if the temperature is below O ° C in winter, the effect will be affected. When the battery is fully charged, the driving mileage will be shortened, because, under this condition, the battery capacity can only be released by 60% – 70%.
Therefore, the driving mileage when the battery is fully charged in winter will be much less than in summer.

Maintenance method

A ,When the temperature is low in winter, the battery should be placed indoors, and the charging should also be carried out indoors. After the battery is fully charged, the charging time should be extended for another two hours.
B , In summer, avoid the sun exposure of batteries. Avoid charging the battery at high temperatures. Avoid charging the battery immediately after use in high temperatures. Do not charge for too long. The battery needs to be charged for another one or two hours after the red indicator turns green.
Use on different road conditions E-bike is not suitable for driving on roads with bad or steep conditions. If there are many uphill on the way, we will find that the mileage of charging once will be much less than that on the flat road. When starting, uphill, loading, or driving against the wind, please use the motor drive combined with a human pedal to ensure the working life of your battery and motor is longer.
Avoid exposure to the sun and rain. Although the electric bicycle has good waterproof performance, it can still ride in rainy and snowy weather, but when passing through water puddles and ponding and other roads, pay attention to the wading height, which should not be higher than the motor, to prevent the motor from damage caused by water inflow. Do not use a high-pressure water gun to wash the electric bicycle, to avoid damage caused by water entering the electronic parts and accessories.
Frequent braking is bound to be accompanied by frequent start-up, which will lead to frequent large current discharge and power cut-off of the battery, which has a certain impact on its life. Countermeasures: pay attention to safety when driving, drive at a proper speed, and try to avoid frequent braking.
BENFUTO TRADING CO., LTD
French Office Add:50 BD STALINGRAD 06300 NICE FR
What’s APP 1: +86 13632624062
What’s APP 2: +44 07355779889
WWW.KETELES.US