BON PERGOLA 13×13 Free Standing Pergola Instruction Manual
- June 17, 2024
- BON PERGOLA
Table of Contents
BON PERGOLA 13×13 Free Standing Pergola
DIMENSION
Villa Pergola for motorized operation
Size: 10’x10’(300x300cm) 10’x13’(300x400cm) 13’x13’(400x400cm)
Please visit www.bonpergola.com for the latest instruction under Q&A section
IMPORTANT INFORMATION
Attention:
Read this instruction manual carefully and completely before mounting and
usage. Keep this manual for future reference.
Dear Customer,
Congratulations and welcome to our Villa Pergola family. To enjoy your Villa
Pergola for its lifetime and for you and other’s safety, please follow the
assembly instructions. Before you start the assembly process and using the
Pergola, we suggest you are best to get familiar with this product. Make sure
all parts listed up in below packing lists are delivered and intact. If you
find that there are parts missing or damaged please do not install the pergola
but contact us immediately. Do not start the assembly process if parts are
missing or defective.
Tools and man force
Recommended: 2 or 3 people Additional tools :
- Ladder
- M10/13 open wrench supplied
- Rubber mallet
- Tape measure
- 5mm hexagon wrench supplied
- Pencil
- Spirit level
- Electric drill
Parts List
Please check all parts against the parts list before commencing construction of pergola.
SIZE:10’x10’ or 300X300CM PARTS LIST:
-
M8x20 countersunk screw
-
50 to 40 connector
-
Base plate
-
Upright cover
-
M10 screw cap
-
M8x20 Hexagon bolt
-
Plastic Space
-
Locking nut
-
Motor with motor bracket
-
M8X100 expansion bolt
-
Gutter connector
-
Footing plate cover
A. Beam with slots
B. Beam with motor direction & slots
C. Beam
D1. Post + post connector
D2. Post + post connector
E. Gutter
F. Gutter
G. Common louver
H. Centre louver
I. Driving louver
J. Control rod
Please check all parts against the parts list before commencing construction of pergola.
SIZE: 13’x13’ or 400X400CM PARTS LIST:
-
M8x20 countersunk screw
-
50 to 40 connector
-
Base plate
-
Upright cover
-
M10 screw cap
-
M8x20 Hexagon bolt
-
Plastic Spacer
-
Locking nut
-
Motor with motor bracket
-
M8X100 expansion bolt
-
Gutter connector
-
Footing plate cover
A. Beam with slots
B. Beam with motor direction & slots
C. Beam
D1. Post + post connector
D2. Post + post connector
E. Gutter
F. Gutter
G. Common louver
H. Centre louver
I. Driving louver
J. Control rod
Product Description:
Make the most of your outdoor living area with your pergola. Relax and
enjoy the outdoors while being protected from sun. The coated aluminum frame
pergola is perfect for shading your garden, deck, courtyard and swimming pool.
Important Safety Instructions:
Warning: For the safety of you and other persons it is important to
follow below instructions and obey warnings.
Symbol explanation
This warning triangle calls attention to hazards that that can lead to death
or to severe injuries or which are important for the functioning of the
Pergola.
This sign identifies important notes.
Safety instructions
To install this pergola technical knowledge is necessary. Do not mount this pergola yourself but contact a professional workman for help if
- you are unsure if the pergola can be mounted on the place you chose for installation.
- you do not understand the instruction manual or parts of it.
- you do not have necessary tools available.
- you do not have necessary technical knowledge
A minimum of three healthy adults are required to move and install the
pergolas the product is big and heavy. Do not try to install the pergola
alone. If the pergola falls, it could cause serious injuries and damages!
Contact an authorized assembler for help.
Do not install the pergola when you find damage parts are that parts are
missing. Contact your dealer.
Keep children and pets out of the working area during assembly and
adjustments.
This product and its fixing parts are only suitable for installation on a
plain cement wall or stable brickwork. If the wall/brickwork shows cracks you
have to consult a professional.
Nobody is allowed to change the products’ design and structure without the
permission of manufacture or authorized deputy.
Please make sure that your hands are clean at the time of the assembly;
otherwise you may soil frame.
Nobody is allowed to climb onto the Pergola. Hanging anything on the Pergola
is forbidden. Sheeting was used to protect the paint. This must be removed
afterwards.
This structure is a non-permanent structure and the warranty does not cover
damage incurred under extreme weather conditions including heavy rain, high
winds or if exposed to high heat from heaters or BBQs.
Safety precautions should always be followed when assembling and using this
product to reduce the risk of personal injury and damage to equipment. Please
read all instructions before assembly and use. Never leave children unattended
around/under this pergola. Do not attempt to assemble or use the pergola in
moderate or heavy wind conditions. Always keep the pergola louver open and
secure it during heavy winds or extreme weather conditions to avoid damage to
the pergola or personal injury.
Step 1
Attach base plate ③ x4 to the bottom of posts ( D1 x2, D2 x2 ,and ),use
bolts ① x16 to attach with hex key or electric drill.
D2 posts should be installed diagonally as below
***NOTE: If you will need to cover the anchor with footing plate cover, put them on before attach base plate to post
Step 2
Attach beam A x1 B x1 and C beam x1,use bolts ⑥ to fasten
Step 3
Attach beam C x1, use bolts ⑥ x12 to fasten
Step 4
Attach upright cover ④ x4,use bolts ⑥ x8 to fasten
Step 5
- Slide the ⑨ motor into F gutter before hooking onto the beam in the direction as shown below.
- Attach all four gutters ( E x2 and F x2 )by hooking inside the A , B , C beams
Step 6
Fasten motor ⑨ x1 with its screws as shown below.
Step 7
- Fasten⑪x4 gutter connector
- If motor wire is running downward through the post, use ② to connect with ⑪ as shown below to not allow water drain through this post.
Step 8
Connect the female and male plugs for the LED lighting (DC24V to DC24V) and
motor (DC24V to DC24V) and Plug the power cable into local socket.
***Note: You can test your motor at this stage. Plug in and use its
remote.
Step 9
Located holes in center of beams ( A and B )
-
Place Center Louver on the slot where it is align with the hole visible. For 10’x10’ (300x300cm):
Place Cen t er Louver H into 12th slot, lining up with the open holes. For 10’x13’ (300x400cm) and 13’x13’ (400x400cm):
Place Center Louver H into 16th slot, lining up with the holes for 10’x13’ (300x400cm) and 13’x13’ (400x400cm) size. -
Using M10 nut ⑤ x2, secure the Center Louver in place.
-
Place Driving Louver I in line with 6th slot if you have a 19-3/4” long motor and 7th slot if you have a 21-1/2” long motor on the beam A and B .
-
Place all Common Louvers G x21 for 10’x10’ (300x300cm) and G x30 for both 10’x13’ (300x400cm) and 13’x13’ (400x400cm) size into the remaining slots in the beams.
Step 10
Fix J x 2 (flat L-shaped aluminum profile). One for each other of the slats is
required.
Use bolt ⑥ x46, plastic spacer ⑦ x46 and nut ⑧ x46 to tighten for 300×300 cm and 400x400cm size.
*Use bolt ⑥ x64, plastic spacer ⑦ x64 and nut ⑧ x64 to tighten for 300×400 cm and 400x400cm size.
Secure the louvers at each end.
***NOTE: Do not over tighten. Over tightening will prevent louvers from
moving/rotating.
Step 11
Mark holes for Wedge Anchor/Bolt x16 for each post Note the drill size should
be 12 mm.
Insert the bolts. Use a hammer drill if necessary. Place the posts over the
bolts. Tighten the nuts.
Once installed, make sure any remaining plastic is removed and silicone is
used along all corners and gutters to be waterproof.
IMPORTANT NOTE:
If you order the screens, please anchor down the pergola to the ground AFTER
installing the screens onto the pergola as it might require minor adjustment
to make screens fit perfectly.
WARNING:
Make Sure louvers are open during periods of mild to strong winds to avoid
damage overtime.
Motor set up
-
Function and Features
- 86mm”86mm, in accordance with international installation standard;
- The electric structure is partla1 conformity with the standard fire protection requirement of the electrician;
- Industrial grade microcomputer chip is used to improve product quality and reliability greatly:
- Use shock-proof current relay;
- Components using precision SMT industry, surface moisture-proof treatment;
- Power supply has safety protection, power supply time is 5 minutes;
- It is used with various emiters and tubular motors.
-
Product Parameters
Produ ct name| Remote controller with light control
---|---
Product model| HC-PM03\O-T1
Rece1v1ng / tran sm,tting frequency| 433 . 92MHz
Work ing temperature| -20°C- +8s·c
Receiv i ng sensitivity| -110dBm
Allowed number of transmitters| ~ap es
Product name| Remote controller with light control
---|---
Product model| HC-PM03F\O-T1
Receiv1ng /transmIlti ng frequency| 433.92MHz
Working temperature| -20°C- +85″C
Receiving sens1hvlty| -11 OdBm
Allowed number of
transmitters
| ap es
3. Operating Instruction
Dismounting
If you want to disassemble the Pergola, please follow the following process.
Attention! At least two people are needed for this step.
- Keep the Pergola louvers open before you begin with dismounting. Bind the Louvers of the Pergola together to avoid unintended unfolding. This might cause damage and injury. You can use the protection band that was fixed on the Pergola when purchasing it.
- Follow the mounting instructions in reversed order to dismount the Pergola.
- Make sure that drilling holes in the wall will be sealed professional.
- Attention! Safety hints and instructions have to be followed for dismounting as well.
Storage
When you do not want to use the Pergola for a longer period of time it is recommended to take the Pergola out of the brackets and store it.
- Make sure that the frame is dry completely before storing.
- Store the Pergola at a dry and safe place that is not reachable for children.
Disposal
Do not dispose this Pergola with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. Dispose packing materials according to local guidelines.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>