BON PERGOLA 202310 Wall Mount 13x19ft Villa Pergola Instruction Manual
- June 17, 2024
- BON PERGOLA
Table of Contents
User Instructions
Villa Pergola motorized operation
Size: 13’x19’ Double Bay
( 400 x 600cm )
Please visit www.bonpergola.com for the
latest instruction under Q&A section
202310 Wall Mount 13x19ft Villa Pergola
Attention:
Read this instruction manual carefully and completely before mounting and
usage.
Keep this manual for future reference.
Dear Customer,
Congratulations and welcome to our Villa Pergola family. To enjoy your Villa
Pergola for its lifetime and for you and other’s safety, please follow the
assembly instructions.
Before you start the assembly process and using the Pergola, we suggest you
are best to get familiar with this product. Make sure all parts listed up in
below packing lists are delivered and intact. If you find that there are parts
missing or damaged please do not
install the pergola but contact us immediately. Do not start the assembly
process if parts are missing or defective.
Tools and man force
Recommended: 2 or 3 people Additional tools :
- Ladder
- M10/13 open wrench supplied
- Rubber mallet
- Tape measure
- 5mm hexagon wrench supplied
- Pencil
- Spirit level
- Electric drill
Parts List
Please check all parts against the parts list before commencing construction of pergola.
SIZE:13’x19’ or 400X600CM PARTS LIST:
SIZE:13’x19’ or 400X600CM PARTS LIST:
Please check all parts against the parts list before commencing construction of pergola.
Product Description:
Make the most of your outdoor living area with your pergola.
Relax and enjoy the outdoors while being protected from sun.
The coated aluminum frame pergola is perfect for shading your garden, deck,
courtyard and swimming pool.
Important Safety Instructions:
Warning: For the safety of you and other persons it is important to follow
below instructions and obey warnings.
Symbol explanation
This warning triangle calls attention to hazards that that can lead to death
or to severe injuries or which are important for the functioning of the
Pergola.
This sign identifies important notes.
Safety instructions
To install this pergola technical knowledge is necessary.
Do not mount this pergola yourself but contact a professional workman for help
if
- you are unsure if the pergola can be mounted on the place you chose for installation.
- you do not understand the instruction manual or parts of it.
- you do not have necessary tools available.
- you do not have necessary technical knowledge
A minimum of three healthy adults are required to move and install the
pergolaas the product is big and heavy. Do not try to install the pergola
alone. If the pergola falls, it could cause serious injuries and damages!
Contact an authorized assembler for help.
Do not install the pergola when you find damage parts are that parts are
missing.
Contact your dealer.
Keep children and pets out of the working area during assembly and
adjustments.
This product and its fixing parts are only suitable for installation on a
plain cement wall or stable brickwork. If the wall/brickwork shows cracks you
have to consult a professional.
Nobody is allowed to change the products’ design and structure without the
permission of manufacture or authorized deputy.
Please make sure that your hands are clean at the time of the assembly;
otherwise you may soil frame.
Nobody is allowed to climb onto the Pergola. Hanging anything on the Pergola
is forbidden.
Sheeting was used to protect the paint. This must be removed afterwards.
This structure is a non-permanent structure and the warranty does not cover
damage incurred under extreme weather conditions including heavy rain, high
winds or if exposed to high heat from heaters or BBQs.
Safety precautions should always be followed when assembling and using this
product to reduce the risk of personal injury and damage to equipment. Please
read all instructions before assembly and use. Never leave children unattended
around/under this pergola.
Do not attempt to assemble or use the pergola in moderate or heavy wind
conditions.
Always keep the pergola louver open and secure it during heavy winds or
extreme weather conditions to avoid damage to the pergola or personal injury.
Step 1
Attach base plate ③x2 to the bottom of posts ( D1 x1, D2 x1 ,and ),use bolts ①
x8 to attach with hex key or electric drill D1 D2 posts should be installed
diagonally as below
***NOTE: If you will need to cover the anchor with footing plate cover, put them on before attach base plate to post
Step 2
According the height of C2 to measure the height of 15 ,use anchor to fasten
Step 3
Use bolts 12 x6 to fasten beam B1 & beam B2
Step 4
Connect A2 / B2 with 13 ,fasten the screws,and insert the middle beam C3 Lock
the screws.
Connect the B1 and B2 , insert C1 into D3 , fasten the screws.
Step 5
Insert the A1 / C1 into D1 ,then connect B1 with 13 ,fasten the screws.
Step 6
Cover the post with 4 x 2,fasten the screws.
Cover the beam on both sides with ,fasten the screws14
Step 7
Placed all gutter E1 , E2 , F1 , F2 in proper position as picture
Step 8
- Fasten ⑩ x2 gutter connector
- If motor wire is running downward through the post, use ② to connect with ⑩ as shown below to not allow water drain through this post.
Step 9
Fasten motor ⑨ x2 with its screws as shown below.
Step 10
Connect the female and male plugs for the LED lighting (DC24V to DC24V) and
motor (DC24V to DC24V) and Plug the power cable into local socket.
***Note: You can test your motor at this stage. Plug in and use its
remote.
Step 11
Place center louver H into 16th slot, lining up with the holes Using M10 nut ⑤
x2, secure the louver in place
Place Steering louvers I x2 in line with 7th slot on the beam A1 and A2
Fit all common louvers G x58 into the remaining slots in the beams
Step 12
Fix J x 4 (flat L-shaped aluminum profile).
One for each other of the slats is required.
Use bolt ⑥ x124, plastic spacer ⑦ x124 and nut ⑧ x124 to tighten for 600X400cm
size.
Secure the louvers at each end.
***NOTE:
- Do not over tighten. If over tighten, louver will not move and possibly damage the louver driver component. Please test the louvers are rotatable by hands smooth and easy to confirm it’s not over tighten.
- Please make sure the Nylon Washer is in between the J and Louver End Cap.
Step 13
- Check for diagonal distance in between the posts L1~L4 and K1~K4 are equal.
- Please note, this step is very important to ensure the pergola are in a rectangle shape in any angle.
It’s extremely important if you are installing a screen before anchor the pergola down or afterward.
Step 14
Mark holes for Wedge Anchor/Bolt 17 x12 for each post Note the drill size
should be 12 mm.
Insert the bolts. Use a hammer drill if necessary. Place the posts over the
bolts. Tighten the nuts.
Once installed, make sure any remaining plastic is removed and silicone is
used along all corners and gutters to be waterproof.
IMPORTANT NOTE:
If you order the screens, please anchor down the pergola to the ground AFTER
installing the screens onto the pergola as it might require minor adjustment
to make screens fit perfectly.
WARNING:
Make Sure louvers are open during periods of mild to strong winds to avoid
damage overtime
Motor set up
Operating Instructions for Remote Controller with Light Control
Function and Features
※ 86mm*86mm, in accordance with international installation standard;
※ The electric structure is partial conformity with the standard fire
protection requirement of the electrician;
※ Industrial grade microcomputer chip is used to improve product quality and
reliability greatly;
※ Use shock-proof current relay;
※ Components using precision SMT industry, surface moisture-proof treatment;
※ Power supply has safety protection, power supply time is 5 minutes;
※ It is used with various emiters and tubular motors.
HC-PM03F\D-T1
① Motor: Up button
② Motor: Stop button
③ Motor: Down button
④ Light bulb: turn on/off button
HC-PM03\D-T1
⑤ Motor: Up button
⑥ Motor: Stop button
⑦ Motor: Down button
⑧ Light bulb: turn on/off button
Product Parameters
Product name | Remote controller with light control |
---|---|
Product model | HC-PM03F\D-T1 |
Receiving/ transmitting frequency | 433.92MHz |
Working temperature | -20℃~+85℃ |
Receiving sensitivity | -110dBm |
Allowed number of transmitters | ≤8pcs |
Operating Instruction
Dismounting
If you want to disassemble the Pergola, please follow the following process.
Attention! At least two people are needed for this step.
- Keep the Pergola louvers open before you begin with dismounting. Bind the Louvers of the Pergola together to avoid unintended unfolding. This might cause damage and injury. You can use the protection band that was fixed on the Pergola when purchasing it.
- Follow the mounting instructions in reversed order to dismount the Pergola.
- Make sure that drilling holes in the wall will be sealed professional.
- Attention! Safety hints and instructions have to be followed for dismounting as well.
Storage
When you do not want to use the Pergola for a longer period of time it is
recommended to take the Pergola out of the brackets and store it.
- Make sure that the frame is dry completely before storing.
- Store the Pergola at a dry and safe place that is not reachable for children.
Disposal
Do not dispose this Pergola with other household wastes. To prevent possible
harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material resources.
To return your used device, please use the return and collection systems or
contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling. Dispose packing
materials according to local guidelines.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>