GEPOW A03411 Semi Flush Mount Ceiling Light Fixture Instruction Manual

GEPOW A03411 Semi Flush Mount Ceiling Light Fixture

Product Information

Specifications

• Mounting plate assembly (C): 1 unit
• Green ground screw (D): 1 unit
• Canopy (E): 1 unit
• Ball knob (F): 2 units
• Upper frame (G): 1 unit
• Tube (H): 1 unit
• Stem (I): 3 units
• Screw (J): 6 units
• Fixture loop assembly (K): 1 unit
• Lower frame (L): 1 unit
• Plastic Wire Connector (A): 3 units
• Mounting screw (B): 2 units

Product Usage Instructions

Assembly & Installation Instructions

1. Carefully remove all parts from the packaging and ensure everything is included.
2. Turn off the power supply before starting any work.
3. Switch off the main power switch in the OFF position at the fuse box or circuit breaker.
4. Turn off the wall switch.
5. Attach the canopy (E) and fixture loop assembly (K) to the tube (H) and tighten it securely.
6. Connect the upper frame (G) and lower frame (L) using the stems (I) and screws (J).
7. Remove the ball knobs (F) from the mounting plate assembly (C).
8. Pass outlet box wires through the centre of the mounting plate assembly (C) and secure it with mounting screws (B).
9. Connect wires according to the provided chart, ensuring the ground wire is connected properly.
10. Position the canopy (E) over the outlet box.
11. Install bulbs (not included) without exceeding the recommended wattage.
12. Ensure everything is properly installed before turning on the light.

Cleaning Instructions
To clean, wipe the fixture with a soft cloth. Avoid abrasive materials like scouring pads, steel wool, or abrasive paper.

Ordering Parts
Keep the instruction sheet for future reference when ordering replacement parts. Parts can be ordered from the place of purchase using the exact wording from the illustration.

FAQ

• Q: Can I install this fixture without a licensed electrician?
  A: It is recommended to have a licensed electrician installed to reduce risks.

• Q: Are bulbs included with the fixture?
  A: No, bulbs are not included. Please purchase bulbs separately and ensure they do not exceed the recommended wattage.

Safety Instruction

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B) Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, with a max of 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (C) Mounting plate assembly (1)

• (D) Green ground screw (1)

• (E) Canopy (1)

• (F) Ball knob (2)

• (G) Upper frame (1)

• (H) Tube (1)

• (I) Stem (3)

• (J) Screw (6)

• (K) Fixture loop assembly (1)

• (L) Lower frame (1)
  ACCESSORIES & QTY ENCLOSED:

• (A) Plastic Wire Connector (3)

• (B) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • B) Place the wall switch in the “OFF” position.

3. Attach the canopy (E) and the fixture loop assembly (K) with a tube (H). Tighten till snug.

4. Connect the upper frame (G) and the lower frame (L) with the stems (I) and fix them onto the stems (I) with screws (J).

5. Unscrew the ball knobs (F) from the mounting plate assembly (C).

6. Carefully pass outlet box wires through the centre of the mounting plate assembly (C). Secure mounting plate (C) to outlet box with mounting screws (B).

7. Make wire connections
   Connect wires as below wires connecting shown below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Twist wires together with plastic wire connector until tightly joined, and wrap each connector with approved electrical tape and be sure that no wire strands are exposed, then carefully tuck all wires into the outlet box.

8. Position the canopy (E) over the outlet box. Align the holes in the canopy (E) with the pre-assembled threaded nipples, then attach the canopy (E) using the previously removed ball knobs (F). Hand tighten until snug.
   Note: The canopy (E) should be snug against the ceiling and the knob balls (F). If not, adjust the length of the pre-assembled threaded nipples on the mounting plate assembly (C) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled threaded nipples in or out of the mounting plate until the length is achieved. Tighten the hex nuts and back to step 8.

9. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

10. Check everything already is installed properly, then you could turn on the light. Enjoy!

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>