OppsDecor OPX496 8 In 1 650lbs Weight Adjustable Workout Bench Set

FEATURES

Flip up the bench back pad to transform into an incline bench and secure with part # 1 7 pin.

Flip out the bench leg to transform into an decline bench with # 16 pin.
The leg exercise bar should put in the other side of the bench.

Fold bench to store. Flip up bench and bench leg and secure with #16 and #17 pins.

The_ Specifications of this product may vary from this photo,subject to change without notice.

• Please retain these instructions for future reference.
• Please do not exceed the weight limitations of this item.
• Maximum Weight for users: 600lbs / 272kgs.
• Do not stand on or use any part of this item as a step ladder.
• Firmly secure all bolts, screws, and knobs before use.
• Fasten screws loosely during initial assembly. Do not firmly tighten the screws until the item is completely assembled.
• Be aware that some parts are heavy and have sharp edges.
• If any parts are missing, broken, damaged, or wrong, stop using this product until repairs are made and/ or factory replacement parts are installed.
• Do not use this item in a way inconsistent with the manufacturer’s instructions as this could void the product warranty.

PRODUCT ASSEMBLY

Step 1 : Attach part H bench support to part D bench leg with two #7 Bolt two # 14 nuts. In this step there are two holes on the Bench leg must upward.

Step 2 : Attach Part J handrail to part Kupper side frame with two #6 screw and #10 washers.

Step3 : Attach Part B side frame to the part C side leg with four pieces

2 carriage bolt and four pieces #9 washers and four pieces #13 nuts.

Attach Part K upper side frame to part B with #3 knob and make sure the knob must insert from both side into the middle.

Step 4 : Assemble the main structure. First, attach part F round support to part B side frame with two #6 screws and two #10 washers. Second, attach part E square support to part B side frame with 4 pieces of# 1 Bolt and #9 washers and # 13 nuts.

Step 5: Attach Part H Bench support to Part A Bench with #5 bolt and #10 washer and #14 nut. Use #16 Pin to secure the bench support angle.
Assemble two #23 plastic knob thumb on each side of Bench.

Step 6 : Assemble bench to main structure, attached A bench to F round support with two #4 bolt and two # 10 washers and two #14 nuts.

Step 7 : Assemble part L dumbbell support with two #6 screw and two # 10 washers.
Assemble part G bracket with two # 15 Pin.

Step 8 : Attach the part N leg holder to the Part I leg exercise bar with

8 screw and #11 washer and #12 nut. Put on the part O roller foam on part N

leg holder.
Put on the #23 plastic knob thumb on part I leg exercise bar.

HARDWARE

1. M10*65mm BOLT 4PCS

| 2. Ml0*65mm CARRIAGE BOLT 4PCS

| 3. Ml0*55mm KNOB 2PCS

| 4. M8*60mm BOLT 2PCS

5. M8*55mm BOLT lPC

| 6. M8*20mm SCREW 6PCS

| 7. M8*60mm CARRIAGE BOLT 2PCS

| 8. M6*45mm SCREW lPC
9. MlO WASHER 8PCS

| 10. MS WASHER 9PCS

| 11. M6 WASHER lPC
12. M6 NUT lPC| 13. MlO NUT 8PCS

14. M8 NUT 5PCS

| 15. 010*80mm PIN 2PCS

| 16. 0868mm PIN lPC
17. 0880mm PIN lPC| 18. 025 CLAMP 2PCS

19. 10-13 OPEN WRENCH !PC
20. 13-17 OPEN WRENCH !PC| 21. #6 ALLEN WRENCH !PC
22. #8 ALLEN WRENCH !PC| 23.PLASTIC KNOB THUMB 3PCS

Step 9: Attach the I leg exercise bar to the bench.
Put parts P rope on part D bench leg.

PARTS

A. BENCH lPC
| B. SIDE FRAME 2PCS
| C. SIDE LEG 2PCS

D. BENCH LEG lPC
| E. SQUARE SUPPORT lPC| F. ROUND SUPPORT lPC

G. BRACKET 2PCS
| H. BENCH SUPPORT lPC
| LEG EXERCISE BAR lPC

J. HANDRAIL 2PCS
| K. UPPER SIDE FRAME 2PCS
| L. DUMBBELL HOLDER 2PCS

M. T FRAME lPC
| N. LEG HOLDER lPC
| 0. FOAM ROLLER 2PCS

P. ROPE 2PCS
| |

Step 10 : Attach the part MT-frame on part I leg exercise bar. Put on the

18 clamp on the part L dumbbell holder.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>