PUET B0BQC3K3MF Automatic Pet Feeder User Guide
- June 17, 2024
- PUET
Table of Contents
B0BQC3K3MF Automatic Pet Feeder
Automatic Pet Feeder
Video Type
Operation Guide
Please Read the Manual Carefully
Before Using the Product
Safety Instruction
-
Children must be accompanied by adults to use it.
-
Do not use the feeder for pets which cannot reach the food tray or have physical disabilities.
-
Do not immerse the base part in water, which will damage electronic components such as control panel.
-
Do not put any foreign objects into the pet feeder.
-
Do not put canned or wet food into the feeder.
-
Do not disassemble the equipment by yourself.
-
Do not modify the pet feeder.
-
lf the equipment can not work or have damaged accessories, do not try to repair the pet
feeder by yourself. Contact the seller immediately and solve it. -
Please make sure the the feeder is unplug and power off when not using or cleaning it.
-
If the plug is damp, please turn off the socket rather than trying to unplug the power.
Notice
-
Please purchase hard plastic protector from hardware store to protect plugs and power cord
then prevent your pet from damaging the accessories. -
Do not put the pet feeder in an high temperature place.The temperature should be within the
range of – 10 ℃~40 ℃. -
Please use alkaline Size D battery for power supply. Do not use rechargeable batteries.
-
Check the battery regularly. Please replace the battery before having a trip.
-
Do not lift the pet feeder directly with the cover, food bucket and food tray. Hold the base
with both hands to lift and carry, while keeping the device in an upright position. -
Only applicable to dry food with a diameter of 2-12mm. Larger food may get stuck or block
the food outlet. -
Please read all the notices on the packing and manuals carefully.
Product Image
Front view
1.Food Tank Lid
2.Food Tank
3.Control Panel
4.Camera
5.Food Outlet
6.Body
7.Food Bowl
Bottom View
8.Speaker
9.Battery Compartment
10.Type-C Interface
Button Description
Recording button: Press and hold for this button until you hear “di” and
start recording.The
recording time does not exceed 10 seconds, After you release your hand, you
will hear “didi” to
indicate that it has been saved.
Delete recording: Press and hold for this button until you hear“di”, then
release your hand, you
will hear “didi” to indicate that it has ended recording. (It is actually used
blank recording to
cover the old recording)
Lock/unlock: Long press this button for 6 seconds and the red indicator
light flashes twice
to lock the machine, then long press again for 6 seconds and the red indicator
light flashes
twice to unlock the machine.
In locked or unlocked state, long press the SET button to restore the factory
settings.
Manual feeding: Short press the FEED button to serve 1 portion, and the
recording will be
played once.
Reset: Press and hold the SET button for 6 seconds until you hear beep
voice to indicate
that it has restored the factory settings. The pet feeder reset automatically
restarts.
Indicator light (blue light)
1. Slow flashing: flash once every 2 seconds, QR code distribution network
and AP hotspot
distribution network mode
2. Steady on: The network connection is successful
3. Power on, WiFi quick connection/AP mode switch: always on for 6 seconds
Indicator light (red light)
1. Flashing: abnormal detection of limit switch (motor does not rotate)
2. Lock/unlock: flash twice
3.When the battery power is enough, the red light is always on; when the
battery is low, it
flashes slowly and cycles
Cleaning and Maintenance
Please clean the feeder regularly to keep your pet’s health.
When it starts to get dirty and a lot of loose food in the food trough, you
can remove the food
cover to clean it.
Please clean the feeder base and the control panel with a soft, damp cloth. Do
not put these
parts into water.
Do not put the product in the dishwasher, otherwise it will be permanently
damaged!
Packing list
After opening the product package, please confirm whether the machine is in
good condition.
Please check the list to confirm whether the accessories are complete.
The Feeder ×1
The power adapter ×1
Power Cord ×1
Product Manual ×1
Specification
Food Tank Capacity:3L
Power supply: DC 5V/1A power adapter; 3pcs alkaline D Size batteries
Power adapter: AC110-240V input, DC5V output
N.G: 1.31KG
Size: 18.5×18.7×31.4cm
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two
conditions : (1) this device may not cause harmful interference, (2) and this
device must accept
any interference received,inc luding interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible
for compliance
could void the user’s authority to operate the equipment.
NOTE:This equipment has been tested and found to comply with the limits for a
Class B digital
device, pursuant to Part l5 of the FCC Rules. These limits are designed to
provide reasonable
protection against harmful interference in a residential installation. This
equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this
equipment does cause harmful interference to radio or televis ion reception,
which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technic ian for help.
To maintain compliance with FCC’s RF Exposure guidelines,This equipment should
be installed
and operated with minimum distance between 20cm the radiator your body: Use
only the
supplied antenna.
Instructions
01 丨 Installation
◎ Remove the feeder from the box.
◎ Place the feeder in the suitable location.
◎ Combine the food tray with the base of the feeder.
02 丨 Connect the power supply
◎ Plug the 5V/1A power adapter into
the wall socket and connect the
device.
◎ The bottom of the equipment is a
rocker switch, which can cut off or
open the power supply.
◎ Open the battery compartment at
the bottom of the feeder and install 3
pcs D size batteries (not necessary) to
prevent power failure
◎ The LED light is turn on to indicate
that the feeder is powered on.
Note:
Does not include battery
Please make sure all parts are clean
and completely dry before turning on
power.
03 丨 Put pet food into food tank
◎Fill the food tank with dry pet food. Close the lid and it
will snap into place due to gravity.
Note:
Do not place canned or wet pet food.
The recommended pet food size range is 2-12 mm.
04 丨 Recording
◎ Press and hold for this button until you hear “di” and start recording.The
recording time does
not exceed 10 seconds, After you release your hand, you will hear “didi” to
indicate that it has
been saved.If you are not satisfied , you can repeat this step to replace the
previous recording.
note:
1)Recording will be played by pressing this button when there is a recording
2)Recording will be played once when feeding
5 丨 Lock/unlock button
◎ under unlock state,Long press for 6 seconds and the red indicator light
flashes twice to lock
the machine, then long press again for 6 seconds and the red indicator light
flashes 2 times to
unlock.
◎ In the locked state, you can press and hold the SET button to restore the
factory settings
Note:
In the locked state, press the feeding button and recording button does not
work,it must
unlock the machine then can use normally.
The APP operation is not affected in the locked state.
6 丨 Feeding
◎ Manual feeding: short press the FEED button to serve 1 portion.And the
recording will be
played once when there is a recording.
Note:
The feeding plan will not be affected
07 丨 Reset
◎ Press and hold this button for 6 seconds until you hear beep voice to
indicate that it has
restored the factory settings.The pet feeder reset automatically restarts.
Smart Life APP specific operations
Simple Troubleshooting
Q:Cannot be configured
A:1) WiFi name and password do not use Chinese, not more than 12 digits,
please use a
combination of numbers and letters, do not support 5G WiFi signal, please use
2.4G WiFi
signal.
2)Some software conflicts in the mobile phone will also cause the network
connection fail.
Please restart the mobile phone, close the non-system software which will
automatically work
when you turn on the phone, then turn on the mobile phone’s bluetooth and
position, and then
try to reconnect.
Q: The feeder is feeding inaccurately or can not work
A: Please check whether there is too much food on the food tray or the food
outlet is blocked;
Please clean the food outlet and food channel usually; when using battery
power, please check
the battery whether is dead or leaking power.
Q:The feeder displays offline
A: Please check whether the distance between the feeder and the router more
than 10 meters
(effective distance is 10 meters);Please keep the feeder and router without
any obstructions.
According to the WiFi characteristics, the WiFi signal will drop sharply if
there have the
obstructions then the connection will unstable which will cause the offline.
Q: No response when turn on the feeder
A: Please check that the feeder is plugged in and the switch is on first. If
both of them are
ready, please check whether the power adapter and power cord are damaged, and
contact
customer service for handling.
Hotspot distribution network (optional)
The specific steps are as follows:
Open the Smart Life APP, select Add Device – Small Home Appliances – Pet
Feeder with Camera
(Wi-Fi) – Click QR Code on the upper right corner- Change to Wi-Fi Mode-Click
AP mode-
Enter the WiFi Password – then go to connect SmartLife -XXXX WiFi signal- Back
to APP
waiting to connect.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>