KMDES W7 Digital Microscope with Screen User Manual

KMDES W7 Digital Microscope with Screen User Manual

Product Overview

1. Thank you for purchasing the digital microscope device. Before using it, please read this user manual carefully.
2. This device complies with Part 15 of the FCC Rules.
3. This equipment will not cause harmful interference
4. This equiment must accept any interference received, including interference that may cause unitended operation.

Operation is subject to the following two conditions:

FCC Radiation Exposure Statement:
This equipment complies with the FCC rediation exposure limits established for uncontrolled environments.

Important Notes

1. Please fully charge the product before first use. Please do not charge directly through the PC, but choose a 5V-2A adapter.
2. This product is not a biological microscope and is not suitable for cell biology research.
3. This product cannot be accurately read microscope magnification, it is a combination of digital and optical magnification microscope, the specific magnification effect is subject to the actual picture taken.
4. When the battery is low, both the storage mode and camera mode cannot be used normally. This is not a product failure.
5. Please protect the lens carefully and make sure to cover the lens with the cap after use to prevent dust or foreign objects from entering.
6. Please pay attention to the placement of specimens or other objects to be observed, and try to place them in the center of the lens directly below.. This will avoid unclear observations and ensure a good user experience.
7. Do not disassemble the product or component struture by yourself to avoid abnormal equipment use

Accessories and tools

Hex key x1| | Screws x 4| | Remote control x1| | Data cable x1| | Fill light x2|
---|---|---|---|---|---|---|---|---|---
HDMI cable x1| | Column x 1| | Base x 1| | Screen x1| | |

How to assemble

Microscope components

1. Connect the both by the connectors as illustrated
   

2. Align the column with the groove and insert it
   

3. Insert four screws into the base to fix the column.

4. Insert the fill light into the USB port.

5. The Type-C on the top of the column is connected to the host as illustrated .
   

6. Insert the latch at the back of the host into the dovetail slot on the column.
   

7. Insert the memory card and remove the lens cap.
   

8. Adjust the height of the host to a suitable level by using the height adjustment knob
   

Function Introduction

Interface usage instructions

Please refer to page 26 for instructions on how to operate after connecting the device to the computer using Type-C.

Button Functions

Function Introduction **

**

1. Power button
   Press and hold for 3 seconds to switch on/off the device.

2. Reset button
   Reset to the original factory defaults.

3. Left button
   Move up/Zoom in/Page up

4. Right button
   Move down/Zoom out/Page down

5. Photo button
   Take a photo

6. Video button
   Start recording/End recording

7. Menu button
   Open the menu/Exit the menu

8. OK button
   Confirm selection/Play/Pause

9. Status indicator light
   Steady on after power on Goes off after power off

10. Infrared sensor
    Receiving infrared remote control signals

11. Fill light adjustment knob
    Left for bright Right for dim

12. Focus ring
    Magnification adjustment Microscope optical focus adjustment

13. Lens light adjustment knob
    Left for dim Right for bringt

14. Height adjustment knob
    Adjust the host to the appropriate height.

15. TF card slot
    Support expansion 0-64G TF card

Supports connection to HDMI display

HDMI output for larger view
Connect the microscope to the screen via an HDMI cable, then turn on the device, and you can watch it simultaneously on the large screen.

Remote Control

• OK button
  Confirm selection/Play/Pause

• Back button

• Photo button
  Take a photo

• Move up/Zoom in/Page up

• Menu button

• Move down/Zoom out/ Page down

• Video button
  Start recording/End recording

• Contains a Battery, Battery Model: CR2050

• Before use, please remove the transparent film from the side of the remote control.

Overall Parameters of Microscope

including class 10
Other| Material| Aluminum Alloy+ABS+PC
---|---|---
Otuprerating tempera-| -10℃ ~45℃
Camera temperature| -10℃ ~45℃
Light source| 8 high brightness LEDs 2 LED fill light
Operating systems| Windows 7and aboveMacOS 11.0 and above
Languages| SEchiminpelsifie/eEdnCghliisnhe/sFera/Tnrçaadisit/ioDneaultscah- nsepseañol/Italiano/Português/ Jap

System Interface Guide

Settings Interface Functions

1. Setting: After powering on, the device defaults to the observation mode. Click , button and then click the button to select settings , click button to enter the settings page, as shown in pictures (1) and (2): “ ” “ ” “ ” “ ”
   

2. Date/Time: Click button to select and then click button to enter the settings page. Click button once to switch between year/month/day, and click button to adjust the digits, as shown in pictures (3):
   
   

Photo Resolution
]Adjust the size of the output image resolution, the higher the resolution, the clearer the image, but the more memory it occupies. The image resolution is divided into：2M、3M、5M、8M、 10M、12M、16M、20M、 24M、36M、 48M。
Exposure Compensation
Exposure compensation is a method ofexposure control, with a range of about ±3-3EV. If the ambient light is dim, you can increase the exposure value (such as adjusting to +1EV, +2EV) to highlight the clarity of the image.
Video Resolution
Change the output video resolution, the higher the resolution, the clearer the image, but the more memory it occupies. The video resolution is divided into720P/1080P/1440P
Date Tags
Turn on/off the display of date label.

Settings Interface Functions

Auto shutdown
Set the automatic shutdown time for the device, you can choose to automatically shut down or turn off the function after 5-60minutes.
Language Settings
Switch device language（Simplified Chinese/Traditional chinese/English/- Français/ Deutsch Español/Italiano/Português/ Japanese）
Line Support
Turn on/off the line assistance function.
Formatting
Initialize the TF card.
Screen brightness
Adjust the device screen brightness (10%-100%) according to the observation needs.
Date/Time
Set the date and time
Light source frequency
Select 60-50Hz in the frequency of the light source
Default Settings
Restore system default settings.
Versions
Device system version.

System Interface Guide

• If the device has sufficient battery power, you can use it directly. The following are the operating instructions without charging.
• If you want to use the device while charging, please refer to the settings on page 26.

1. Take a photo / Record a video: After powering on, the device defaults to the observation mode. Click ” “button for taking a photo or click” “button once for ending the record. “button for recording and click
   

2. Photo Preview: Click ” “, click ” “button to enter menu mode, click “ “button to select “button to enter the photo browsing page, as shown in pictures
   

3. Video Playback: Click ” “button to enter menu mode, click ” “button to select “, click ” ” button to enter the video browsing page, as shown in pictures (2).

4. When browsing page, click” screen” – “, as shown in pictures (3): button 1-2 times to locate at the top left corner of the
   a. Page switching: Click” click” “button to flip the page. “button to select “Previous Page/Next Page” and
   b. Delete file: click” button to select Sela, click” “button to select, click” ” button to locate to Select as shown in pictures (4), and then click” to select Delete, click” “button to delete.
   

5. When viewing photos in full-screen mode click botton for page turning . “ ”“ ”

6. When video playback, click button to rewind, click button to fast forward,

7. click button to pause/start. As shown :
   

Usage Instructions on computer

Different systems require different software. Please choose and download the corresponding software based on your system.
Download for Windows system (Supports Windows 7/8/9/10/11 or higher versions)

1. When using Windows 7 and above,download the application“UniLab ” Download link ：http://[www.weetool.net](http://www.weetool.net)
   Select UniLab for Windows or amcap v3.0.9 for loading，as shown：
   
   

2. When using Windows 10 and higher versions, search for the software in
   the Microsoft Store“UniLab” or use the pre-installed software on yo computer called“ Camera ”

Software “unilab”page, as shown:

Software “Camera”page, as shown:

Note: To switch the camera, click button located at the top right corner of the screen. If the image still cannot be captured, please adjust the privacy settings of your camera.
For Apple systems (Supports macOS X 11.0 or higher versions):

3. Using the pre-installed software on your Apple computer called “Photo Booth”
   Software “Photo Booth”page, as shown:
   
   

Usage Instructions on computer

1. Connect the Type-C cable that comes with the original packaging to USB port of the computer.
   

2. After powering on ，click button to select as shown in pictures(1), click , button as shown in pictures (2), You can watch by opening the software on your computer. (Please refer to pages 22-25 for the software startup page.)

3. Note: At this time, the microscope screen does not display images, and the button functions cannot be used. This is a normal phenomenon. (The brightness adjustment button, focus ring, and power button can be used normally.)

4. After powering on， click button to select as shown in pictures(1), click , button as shown in pictures (3), You can read, write, and format on the computer side. “ ” “ ” Memory

5. After powering on， click button to select as shown in pictures(1), click  button as shown in pictures (4), At this time, the microscope directly displays the observed object.

Usage Instructions on computer

1. 
2. 

3. 4. Problem description	Causes	Solutions
      Dcheavricgedc.annot be	①②secTNuhreplcyhpalruggingoegdpioner.tsis not
      ted.③ Deovicoewmeraslfuunrcctioin.connec	①② RCeo-

      npnluecgttthheeinptoewrfearcseufiprpmlyly. .
      tDoecvoicme pcauntenrostocfotwnnareect side.| Lccaobbolseee, coornnnoetcutsioinng, daacmonangecdtidoantaaalityl.  with data transfer function-①The object is not directly below| Rwdaet-aplcuagbtatlhee,raoinr tuesrefaaced,arteapclabcelethetoitrhecdoannetctnasnmdius seo.n function① Check the placement       the
      Tcahuesiemdabgyetbhleurlerinnse.ss Product cannot be| t②heT camfoecraal llennsg.th is not adjusted c③toTthe oligphtitminagl ipsonsoittiobne.ing used4oTrrheectlleyn. s is fogged up| ③bAjedcjut.st the lightin②g pRreofpoecurlsy..4 sWtabitilfiozre.thUeseteimt apgeariantuarfteetrothefog has dissipated for a while.
      aturernuendreosffponbsiuvtet.ons| Crash| Prelestaasret.perform a reset and

Operating Environment

Storage Environment

• Store in a cool, dry place away from direct sunlight for daily use

• Avoid storing the microscope in places where there is a risk of falling. Falling may cause deviation of the internal lenses or damage to other components, as well as other irreparable damage issues.
  You can charge the microscope using a regular phone charger, computer, or power bank.
  
  Please do not exceed 12 hours of charging time to avoid affecting the battery’s lifespan.

• During the charging process, it is normal for the microscope shell and battery to have slight heating, please use it with confidence.

Please use it in an environment between -10℃ and 45℃

Please avoid themicroscope being splashed with water, drinks, or corrosive liquids.

Please avoid placing the microscope near heat sources, open flames, and flammable or explosive gases or liquids.

Please avoid impacting and violently shaking the microscope.

References

• 我的网站

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>