DECKED DG6 Truck Bed Storage System Instruction Manual

June 17, 2024
DECKED

DECKED-Original-Logo

DECKED DG6 Truck Bed Storage System

Product Specifications

  • Model: DG6/DG7/DGB
  • Version: v.10
  • Drawer Handle Type: Grab your bag
  • Installation Method: Clevis Pin

Installing the Drawer Handle

  1. Ensure each spring arm is pointing inward, with the straight tails facing you and pointing down.
  2. Hold the spring in the cavity with a clevis pin, hooking the notch under the spring arm.
  3. Install a clevis pin through each outside drawer hole and through the spring.
  4. With the DECKED logo facing outward, insert the handle ends behind the spring arms.
  5. Hook the spring arms into the handle notches and rotate the arms of the handle toward the clevis pins to pull the spring arm downward.
  6. Align the handle hole to the clevis pin and push the pin through the handle hole and inside drawer hole. Repeat on the other side of the handle.

Installation Instructions

DG6/DG7/DGB
CHEVY SILVERADO/GMC SIERRA
*NEW BODY STYLE ONLY**
5’9″, 6’6″, 6’9″ BED LENGTHS
1500: (2019-CURRENT) SHORT &STANDARD BEDS
2500 & 3500: (2020-CURRENT) STANDARD BEDS ONLY

IMPORTANT: If installing a CargoGlide on top of this drawer system, DO NOT install the drawer system into your truck yet – SEE INSTRUCTIONS.

TOOLS REQUIRED

  • 3/8″ socket
  • 7/16″ open wrench
  • 1/8″ hex wrench
  • 7/16″ socket
  • 7/32″ hex wrench
  • 1/2″ drill bit
  • Wire cutters
  • Cold beverages

DECKED -6Truck-Bed-Storage-System-1 DECKED
-6Truck-Bed-Storage-System-2IMPORTANT: If installing a CargoGlide along with this drawer system, DO NOT install the drawer system into your truck yet – SEE INSTRUCTIONS.
THEY! TORQUE BOY: READ BEFORE YOU INSTALL THE DECKED DRAWER SYSTEM

  • DON’T go rogue on us, please read the instructions.
  • Start all bolts with your fingers to avoid cross-threading -you don’t want to spin out any inserts.
  • DON’T over-tighten bolts, get em’ hand-tight…or you will spin out the inserts.
  • DON’T use power tools.
  • If you don’t follow directions and do use power tools, please set the clutch at a very low setting.
  • Over-torquing or using an impact wrench will spin outthe inserts -we’re warning you!
  • If you blow it, you can screw the inserts back in from the opposite side with a slotted screwdriver.
  • If you really blow it, we’ve included some repair inserts in the PREP-EXTRA bag-install with a 7/32″ hex wrench. Call us if you need more.
  • You’ll need a buddy for exactly two steps.
  • Torque ratings are suggestions for all fasteners until snug.
  • Prevent expletive-filled language, watch our detailed installation video or give us a call. We’re happy to help!

AMMO CAN DRAIN HOLES

(TO DRILL OR NOTTO DRILL)

  • Do you use a tonneau or shell over your DECKED system?
    There is no need to drill holes, unless you leave your tonneau open in a deluge.

  • Does your DECKED system live outside?
    The ammo cans will get water in them. You’ll need to drill holes in the ammo cans.
    There are two dimples in the bottom of each ammo can. Drill a 1/2″ hole at each dimple.
    A smaller hole will get clogged. Depending on the system, we may have drilled these for you already.

DECKED -6Truck-Bed-Storage-System-3 IMPORTANT!
THE NEXT STEP (BRACKET INSTALL) IS DEPENDENT ON TRUCK BED LENGTH:

  • DG6 – 5’9” BED LENGTH: GO TD PAGE 5
  • DG7 – 6’6” BED LENGTH: GO TD PAGE 5
  • DGB – 6’9” BED LENGTH: GO TD PAGE 6

DG & & DG7 PREP BED: BRACKET INSTALL
STOP Double-check that you have a Silverado/Sierra with a 5’9″ bed [DG61 or a 6. 6’6″ bed [DG71.

DECKED -6Truck-Bed-Storage-System-4 DECKED
-6Truck-Bed-Storage-System-5 DECKED -6Truck-Bed-Storage-
System-6 DECKED -6Truck-Bed-Storage-
System-7

GET THE REST OF YOUR DECK ON

  1. Seat the driver side panel on the ammo cans and center vert.

  2. Attach the panel to both ammo cans, repeating steps 4and 5 from the previous page.

  3. Do not attach the driver side panel to the center vert. Do I have to repeat myself?

  4.  Now you can tighten the eight (8) C-CHNL to ammo can bolts. Don’t forget unless you like rattles.
    DECKED -6Truck-Bed-Storage-System-13
    If you will be installing a CargoGlide onto the DECKED drawer system, now is the time to grab your CargoGlide instructions. Do not put the drawer system in your truck.

  5. Gently remove the driver side assembly from the vert and put aside. If you attached the driver side panel to the vert, see tt3 above, smack your hand and carefully remove the bolts.

  6. Find a friend to help you lift and place the passenger side assembly into the bed of your truck. Nicely ask the same friend to lift and place the driver side assembly into the bed and seat the panel onto the center vert.

  7. Install the driver side panel to the center vert using the remaining plain BOLTS L bolts. 27 in-lb.

DRAWERS: BRACKETS+ WHEELS
(EASIER THAN FALLING OFF A LOG)

Brab your bag:ORAWER I/DRAWER 3/WHEELS

  • Each drawer has a left and a right wheel bracket. Place the brackets into the drawers as shown.
  • Install two 3/4″ bolts into the bottom two bracket holes. Secure with nuts. Leave loose for now. DETAIL A.
  • Install the 2″ bolt into the back mounting hole where shown. Secure with a nut. 27 in-lb. DETAIL A.
  • Tighten bottom two bolts. 27 in-lb.
  • Use two 3/4″ bolts to install the tube brace. 27 in-lb. DETAIL B.
  • Install the wheels with a 7 /32″ hex wrench. 90 in-lb. DETAIL C.

DECKED -6Truck-Bed-Storage-System-14 DECKED
-6Truck-Bed-Storage-System-15

INSTALL: DRAWER HANDLE

Orab your bag: HANDLE

  • DK, Sparky, one drawer handle assembly needs to be installed by you. We did the other one. Save yourself the headache, watch this short installation video: How to Install DECKED Drawer Handle

  • From the front face of the drawer, place the springs up and into the cavities on either side of the handle slots, red spring=right spring.
    DECKED -6Truck-Bed-Storage-System-17NOTE: Each spring arm should point inward, with the straight tails facing you and pointing down.
    DECKED -6Truck-Bed-Storage-System-18

  • Install a clevis pin through each outside drawer hole and through, the spring.

  • With the DECKED logo facing outward, insert the handle ends behind the spring arms. Hook the spring arms into the handle.
    notch and rotate the arms of the handle toward the clevis which will pull the spring arm downward.

  • When the handle hole is aligned to the clevis pin, push the pin through the handle hole and through the inside drawer hole. Repeat on the other side of the handle.
    Install a hairpin through the clevis pin.

  • Save yourself the headache, watch this short installation video: How to Install DECKED Drawers and Tailgate Drawer Wheels

  • Install the drawer by sliding wheels into their two channels (C-channel and center vert), and slide drawer all the way forward until closed.

  • Install the remaining tailgate side wheels onto their axles. 90 in-lb. Install the weatherstrips AFTER you install the wheels.
    NOTE: Placing a spacer under the drawer to raise it Into position makes this easier (ammo can lids work well, or a small piece of 2×2 or 2×4).

  • Install the weather strips on the tailgate side drawer edge: With the weatherstrip wiper facing cab side, line up one end with the side of the drawer and place on the top drawer edge, firmly pressing down on the weatherstrip as you move along the drawer edge.
    NOTE: Facing the weather stripping the wrong way will funnel water Into drawer: BAD!
    DECKED -6Truck-Bed-Storage-System-22

  1. Slide torsion brace under center vert and tailgate ammo cans. The side without the holes slides UNDER the center vert and tailgate ammo cans. Place bottle opener on the outside of the torsion brace.
  2. Loosely install (start with your fingers to avoid cross-threading):
    • Two 1/2″ black bolts through the upper holes in the bottle opener into the center vert -leave loose.
    • Two l” black bolts through the bottom bottle opener holes and torsion brace into the center vert inserts -leave loose.
    • Two l” black bolts through the end holes in torsion brace into the tailgate ammo can inserts-leave loose.
  3. Align bottle opener to edges of center vert and tighten the four bottle opener bolts.
  4. Tighten end bolts into tailgate ammo cans.
  5. Install lock core plugs into the drawer lock holes or install locks if purchased. (Instructions included with locks)
  6.  Align the ruler plate on the tailgate end of the panels. Use an 1/8″ hex wrench to install the six ruler screws into the panel inserts- do not overtighten these.

DECKED -6Truck-Bed-Storage-System-23 THE NEXT STEPS ARE DEPENDENT ON TRUCK BED LENGTH

  • 5’9″ BED LENGTH • DG6: PAGES 14 AND 15 6’6″ BED LENGTH –
  • DG7: PAGES 14 AND 15 6’9″
  • BED LENGTH – DGB: GO TD PAGE 16

STOP: Double check that you have a Silverado/Sierra with a 5’9″ bed [0661 or a 6’6″ bed [0671.

DG & + DG7 INSTAll: CABS I DE J-HOOKS 

CABSIDE AMMO CAN J-HOOK INSTALL

  • Insert the J-hook through the tailgate hole on the passenger side cabside ammo can and loop J-hook through tie down or mounting bracket in bed.
  • Screw on the winged-spherical nut-washer, round side down, on the J-hook and fasten until finger tight. Don’t tighten yet.
  • IMPORTANT: Leave all J-hook nuts LOOSE until all J-hooks are installed. If you tighten the J-hooks, you won’t be able to center the system properly.
  • Repeat with J-hooks and ammo cans on drivers side.

DECKED -6Truck-Bed-Storage-System-24

STOP• • Double check that you have a Silverado/Sierra with a 5’9″ bed [0661 or a 6’6″ bed [067].

  • Insert the J-hook through center hole on the passenger side tailgate ammo can and loop J-hook through tie down or mounting bracket in bed.
  • Screw on the winged-spherical nut-washer, round side down, on the J-hook and fasten until finger tight. Don’t tighten yet.
  • IMPORTANT: Leave all hook nuts LOOSE until all J-hooks are installed. If you tighten the J-hooks, you won’t be able to center the system properly.
  • Repeat with J-hooks and ammo cans on drivers side.

DECKED -6Truck-Bed-Storage-System-25

STOP : Double check that you have a 2500/3500 Silverado/Sierra with a 6’9″ bed [0681. If you

  • Insert the J-hook through the tailgate hole on the passenger side cabside ammo can and loop J-hook through tie down or mounting bracket in bed.

  • Screw on the winged-spherical nut-washer, round side down, on the J-hook and fasten until finger tight; BAG J5. Don’t tighten yet.
    IMPORTANT: leave all J-hook nuts LOOSE until entire deck is in place. If you tighten the J-hooks, you won’t be able to center the system properly.

  • Repeat with J-hooks and ammo cans on drivers side. DECKED -6Truck-Bed-Storage-System-26

TAILGATE AMMO CAN J-HOOK INSTALL: grab your bag:11

  • Insert the J-hook through tailgate hole on the passenger side tailgate ammo can and loop J-hook through tie down or mounting bracket in bed.

  • Screw on the winged-spherical nut-washer, round side down, on the J-hook and fasten until finger tight. Don’t tighten yet.
    IMPORTANT: leave all J-hook nuts LOOSE until entire deck is in place.

  • Repeat with J-hooks a?ammo cans on drivers side. DECKED -6Truck-Bed-Storage-System-27

TIGHTEN: J-HOOKS/INSTALL AMMO CAN WINDOWS ANO LIDS

  • Finally, tighten the J-hooks, gradually and alternately.

  • DO NOT OVER TIGHTEN. DETAIL A.
    IMPORTANT: Make sure to center the bottle opener on the vert in the center of your bed. Don’t worry about side gaps, cell/er !he ver! Oil !he ce!l!er rib or valley of !he bed.

  • Install thread bolt protectors on J-hook ends.

  • Orient the “O” on the ammo can window as shown – DETAIL B. Engage the bottom tab into the ammo can window and push the top tab into place.

  • Install the ammo can lids. DETAIL C.

  • Nice job. Your mother and I are very proud of you.

  • If your tailgate does not lay flat and the drawers rubon the tailgate, please install the GM TAILGATE BOLTS in your hardware kit. Instructions are in the bolt bag.

IMPORTANT: Grab your favorite beverage, crack ‘er open in the bonle opener and make a toast to your truck. You did it. Immediately post a photo of your significant other, child or canine Un no order of significance- please someone show us your pet alligator) appreciating your accomplishment. Add hashtag

OECKEDUSA I @DECKEOUSA.

INSTALLATION INSTRUCTIONS: GM TAILGATE CABLE BOLTS
Does your tailgate slope upwards when open? No problem, read below:
If your drawers rub, substitute the factory-supplied tailgate cable mounting bolts with included DECKED cable bolts. Our bolts have smaller diameter shoulders allowing the tailgate to sit flatter. DECKED has utilized an independent testing lab to physically test the tailgate cable assembly with the modified bolts to ensure tailgate load capacity has not been diminished.
You’ll need a 13mm and 15mm socket, or a crescent wrench.

  • Open tailgate and rest the underside of the tailgate on a protected support surface.
  • Using a 13mm socket, remove the shoulder screw securing the driver side cable attachment to the tailgate, DETAIL A.
  • Referencing the image below, remove the push nut fastener that retains the shoulder screw and locating washer to the cable. Easiest to just snip the push nut with wire cutters to remove, they are not needed for reuse.
  • Replace the factory supplied shoulder bolt with the silver shoulder bolt supplied in your kit, ensuring you reassemble the locating washer in the same orientation as when you removed it. Reference installed views below for locating washer orientation.
  • loosely assemble the tailgate end of the cable to the tailgate, orienting the locating washer tab into the rectangular hole in the tailgate.
  • Using a 15mm socket, tighten bolt to 11 ft-lb.
  • Repeat steps 1-5 for the tailgate end of passenger side cable.
  • Repeat steps 1-5 for the driver and passenger side vehicle cables, DH All 8.

DECKED -6Truck-Bed-Storage-System-30
DECKED Products – Limited Lifetime Warranty
(Valid on DECKED Products purchased on or after 8/1/2021)
DECKEO LLC, (the “Manufacturer”) warrants the original purchaser only that DECKED Truck and Van Products (The “DECKED” Product) will be free from defects in material and workmanship from the date of purchase and continuing for the expected lifetime of the DECKED Product. The DECKED Product must be registered by the original purchaser with DECKEO. LLC via its website at, www.decked.com/register, and a copy of the original sales receipt must be supplied to the Manufacturer at the time a warranty claim is made. This warranty terminates if the original purchaser transfers the DECKED Product to any other person or vehicle.

WHAT IS COVERED
All DECKED Products identified above on or after August 1, 2021
DECKED’s limited lifetime Warranty applies to us and Canadian customers only, International shipments are covered by DECKED’s 3 Year limited Warranty.

WHAT WE WILL DO TO CORECT PROBLEMS
Subject to the limitations and exclusions described in this limited warranty, the Manufacturer will remedy defects in workmanship or materials by providing one of the following remedies at ns option and without charge to the original purchaser for parts:

  • (a) repairing the defective portion of the DECKED Product, or
  • (b) replacing the entire DECKED Product.

In addition, the Manufacturer may elect at its option not to repair or replace the DECKED Product, but rather issue to the original purchaser a refund equal to the purchase price paid for the DEC KEO Product or a credit to be used towards the purchase of a new DECKED Product.

WHAT IS NOT COVER
This limited warranty expressly excludes:

  • Damage or defects caused by normal wear and tear, cosmetic rust, scratches, accidents, unlawful vehicle operation, installation in a non-­supported vehicle or installed in a vehicle which does not match the DECKED
  • Product’s SKU-intended fitment or use, or modification of the product. or any types of repair of a DECKED Product other than those authorized or provided by the Manufacturer.
  • Damage or defects resulting from conditions beyond the Manufacturer’s control and specifications including, but nor limited to modification, misuse, overloading, or failure to assemble, install or use the DECKED
  • Product in accordance with the Manufacturer’s written instructions or guidelines included with the DECKED Product or separate? made available to the original purchaser.
  • Damage to the contents of the DECKED Product or vehicle.
  • TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR ANY INCIDENTAL, SPECIAL INOIRECT, OR CONSEQUENTIAL DAMAGES, INCLUOING ECONOMIC
  • LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE, OR INABILITY TO USE THE DECKED PRODUCT OR THE MANUFACTURER’S NEGLIGENCE.

ND OTHER EXPRESS WARRANTY APPLIES
This Limned Lifetime Warranty is the sole and exclusive warranty for DEC KEO Products. No employee, agent, dealer, or other person is authorized to after this warranty or make any other warranty on behalf of DECKED LLC.

NOTIFICATION PROCEDURES
If the DECKED Product does not conform with the terms of this limited warranty, the original purchaser must prompt? notify the Manufacturer in writing upon discovery of the nonconformity. In order to receive remedies under this limited warranty, a warranty claim must have been registered with DECKED UC by the original purchaser, must describe the nature of the products nonconformity, include a copy of the original sales receipt, invoice, or other proof of purchase and be accompanied with photos or video. Repairs or modifications made to the DECKED Product by other than the Manufacturer or its authorized agent will nullify this limited warranty. Coverage under this limited warranty is conditioned at all times upon the owner’s compliance with these required registration, notification, and repair procedures.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

DECKED User Manuals

Related Manuals