BEJOAN 7.06.07.461-01 Z1 Bidet Toilet Seat Instructions

BEJOAN 7.06.07.461-01 Z1 Bidet Toilet Seat

Specifications

• Product Type: Smart Bidet Toilet Seat
• Product Model : SBTS-2000
• Product Name : ComfortClean Bidet
• Rated Power: 1200W
• Maximum Power: 1400W
• Rated Voltage: 120V
• Rated Frequency: 60Hz
• Range Of Inlet Water Pressure: 0.07-0.75MPa
• Waterproof Grade: IPX4
• Warm Water Temperature: 34-40°C
• Warm Air Temperature: 32-40°C
• Seat Temperature: Adjustable, 34-40°C

Important safeguards

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING

DANGER- To reduce the risk of electrocution:

1. Do not use it while bathing.
2. Do not place or store the product where it can fall or be pulled into a tub or sink.
3. Do not place in or drop into water or other liquid.
4. Do not reach for a product that has fallen into the water. Unplug immediately.

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use it while sleeping or drowsy.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

DANGER – Improper use of the grounding plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.

This product is for use on a nominal 120 V circuit and has a grounding plug that looks like the plug illustrated in sketch A in Figure 75.1. A temporary adapter, which looks like the adapter illustrated in sketches Band C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by the screw.

If it is necessary to use an extension cord, use only a three-wire extension cord that has a three-blade grounding plug, and a three-slot receptacle that will accept the plug on the product. Replace or repair a damaged cord.

Grounding methods

Installation announcements

Do not plug or unplug the power plug with wet hands.

• Doing so may cause electrical shock.
• Do not get any water or cleaning products on the main unit or power plug.
• Doing so may cause a fire, electrical shock, heat, or a short.
• Doing so can cause the product to crack resulting in injury or water damage.
• Never disassemble, repair, or alter.
• Doing so may cause a fire, electrical shock, heat, or a short.
• Do not install the Washlet on moving vehicles such as RVs or boats.
• Doing so could cause a fire, electric shock, or a short, or malfunction.
• The toilet seat, lid, main unit, or other part might come loose and fall apart, resulting in injury.
• Do not use the Washlet if a malfunction occurs.

In the following cases, unplug the plug from the outlet and close the water supply valve.

• Possible malfunctions

  • Water is leaking from a pipe or the main unit
  • The product is cracked or broken.
  • The product makes a strange noise or emits a strange odor.
  • The product emits smoke.
  • The product is abnormally hot.
  • The toilet seat cushion is out of place.

• Continued use after malfunction could cause a fire, electrical shock, heat, short, injury, or water

• Only use tap water or potable well water (underground water). Do not use seawater.

• Doing so may irritate the skin and malfunction.

• Do not touch the power plug during thunderstorms.

• Doing so may cause electrical shock.

• Do not allow the water supply hose to touch the power plug or outlet.

• Doing so may cause condensation resulting in a fire, electrical shock, heat, or a short.

• Do not do anything that could damage the power cord, power plug or toilet seat cord.

• Do not strike, yank, twist, excessively bend, damage, alter, or heat the electrical cords. Also, do not place anything heavy, bind, or pinch the electrical cords.

• Using a damaged electrical cord may result in a fire, electrical shock, heat, or shor

• Do not use a loose or faulty electrical outlet.

• Doing so could cause a fire or a short.

• Do not use any outlet or wiring equipment beyond its specified rating

• Plugging too many plugs into the same outlet, for example, using outlet splitters can cause fire due to heat.

• Do not use any power supply other than the one specified.

• AC 120 V, 60Hz

• Doing so could cause a fire or excessive heat.

• Do not stick a finger or anything else into the warm air outlet.

• Do not place anything on the warm air outlet or drape clothes over it.

• Beware of low-grade burns

• Improper use of heated toilet seats could cause a low-grade burn.

• When sitting for a long time on the toilet seat, switch the toilet seat temperature adjustment to “OFF”.

• When any of the following persons use a heated seat or warm air drying, someone should switch the toilet seat temperature adjustment to “OFF” and switch the drying air temperature to “Low”.

  • Young children, the aged, and other users unable to set the temperature appropriately themselves
  • The ill, physically disabled, and others who do not have freedom of movement
  • Those using any medicines that cause drowsiness (sleeping medicine or cold medicine), those who have been drinking heavily, anyone severely fatigued, and anyone else liable to fall asleep

• Always connect the Washlet to the cold water supply.

• Connecting to a hot water supply may result in burns and equipment damage.

• Make sure that a properly grounded (3-prong) outlet has been installed.

• Failure to install a grounded outlet could cause electrical shock in the event of a malfunction or short circuit.

• Do not unplug by pulling the cord.

• To unplug, hold the plug, not the cord.

• Pulling on the cord may cause damage and result in fire or heat.

• This is an electrical product. Do not install it anywhere water is likely to get on the product or anywhere with humidity high enough that water is likely to form on the surface of this product. When using the product in a bathroom, install a fan or ventilation port and ensure good airflow through the bathroom.

• Failure to do so could cause a fire or electrical shock.

• If the electric cord is damaged, avoid danger by having the manufacturer’s repair department or equivalent specialist replace it.

• Insert the power plug securely into the outlet.

  • Failure to do so could cause a fire, heat, or a short.

• Periodically remove dust and dirt from the electrical plug and make sure it is securely plugged into the wall outlet.

• Failure to do so could cause a fire, heat, or a short.

• Pull the plug out from the outlet and wipe clean with a dry cloth.

• Always unplug the plug from the outlet before cleaning or maintenance.

• Failure to do so may cause electrical shock.

• Except when using “Wand cleaning”

• Always unplug the plug from the outlet before removing the main unit.

• Failure to do so could cause a fire or electrical shock.

  • Keep cigarettes and other open flames away from this product.

• Failure to do so could cause a fire.

  • When cleaning or maintaining the plastic parts (main unit etc.) or the water supply hose, use a kitchen cleaner diluted with water. Do not use any of the following.
    Toilet cleaner, household cleaner, benzene, paint thinner, powdered cleanser or nylon scrubbing pads.

• These items could damage or crack the plastic and cause injury or malfunction.

• These items could damage the water supply hose and cause a water leak.

  • Do not apply strong force, or mechanical shock, step on or stand on the toilet seat, toilet lid or main unit. Also do not place any heavy objects on the toilet seat, toilet lid or main unit.

• Doing so could cause cracking or cause the main unit to come loose and fall resulting in injury.

• Doing so could damage the product and cause injury or water damage.

  • Do not lift up this product by the toilet seat or lid.
  • Do not raise the toilet seat or lid while objects are resting on top of the toilet.

• Doing so could cause the main unit to come loose and fall resulting in injury.

• Do not fold or crush the water supply hose.

  • Doing so could cause water leaks.

• To prevent a sudden water leak, do not remove the water filter drain valve when the water supply valve is open.

• Doing so will cause water to spurt out.
  Refer to Page 37 for instructions on cleaning the water filter drain valve. Do not install the base plate, which is not attached, to the Washlet.

• Doing so could cause a fire or damage.

• Do not use the product if the main unit is unstable.
  If a water leak should occur, always close the water supply valve. Preventing damage to pipes and hoses due to freezing

• Frozen water pipes could cause the main unit and the pipes to break, resulting in a water leak. Regulate the room temperature to prevent the pipes and hoses from freezing during cold months. When not using the Washlet over an extended period, drain the waterout of the Washlet and the water supply hose, and pull the electrical plug from the outlet.

• When using the product again, allow the product to refill with water first.

• Otherwise, the water in the tank might become contaminated and cause skin inflammation or other problems.

• Leaving the power ON might cause a fire or heat.

• When installing the water filter drain valve, make sure that it is securely tightened in its proper position.

• Failure to securely tighten it might cause water leaks.

• Push the main unit securely onto the base plate.

• After pushing the main unit until a click sound is heard, pull it slightly toward you to make sure that the product does not detach.

• Failure to do so could cause the main unit to come loose and fall resulting in injury.

Packing list

Installation method(Main body installation)

Installation of the intelligent toilet and ceramic body

1. Press and hold the disassembly button, pull down the machine mounting plate, and take out the machine mounting plate from the machine;
2. Screw the cross cup head machine screw M6*45 out of the rubber fixing sleeve, and then put the rubber fixing sleeve into the whole mounting plate on the ceramic body;
3. Place the machine mounting plate, mounting bracket, and cross cup head machine screw 6*45 above the mounting hole of the ceramic body;
4. Screw the cross cup head machine screw M6*45 into the rubber fixing sleeve, fix the mounting bracket and the whole mounting plate on the ceramic body;
5. Align the bottom of the toilet with the direction of the machine mounting plate, lift the back of the body upwards, and then slide it toward the machine mounting plate until you hear a “click” sound.

Installation method(Main body installation)

Water Supply Hose and intelligent toilet body installation

Noma! installation:
Water supply hose and water diversion valve installation:

1. Close the water supply valve and remove the water supply hose connected to the ceramic;
2. Install gaskets at both ends of the water diversion valve;
3. Install the water diversion valve on the water supply valve;
4. Install the ceramic-connected inlet pipe on the water diversion valve.

Note: Be sure to tighten it during installation, otherwise it may cause water leakage.

Adapter installation required

Water supply hose and water diversion valve installation:

1. Close the water supply valve and remove the water supply hose connected to the ceramic;
2. Install adapters&gaskets at both ends of the water diversion valve;
3. I nsta II the water diversion vavle on the water supply vavle;
4. Install the ceramic-connected inlet pipe on the water diversion valve.

Note: Be sure to tighten it during installation, otherwise it may cause water leakage.

Installation method{Main body installation)

Water Supply Hose and intelligent toilet body installation

• Make sure that the 0-ring part of the water supply hose is not attached to dust, and insert it straight into the connection part on the body side.
  Note:

  • Make sure that the front of the water supply hose is equipped with a 0-ring.
  • Do not cut the water supply hose.
  • Do not use the old water supply hose, otherwise it will leak due to aging.
  • Do not allow the water supply hose to be scratched by sharps.
  • The water supply hose must be inserted straight to avoid the 0-ring being engaged by the body connection.
  • Insert the metal snap into the connection between the water supply hose and the body connector. (until hearing a “bang” sound).
  • When holding the water supply hose, turn the metal snap slightly, and make sure that there is no obstacle when turning.
  • If there is obstacle when turning, it is indicated that the installation is not correct.

Water Supply Hose and intelligent toilet body installation

• Confirm whether the metal snap is firmly fixed. Slightly pull the water supply hose and confirm that the water supply hose will not be separated from the main body.
• Confirm that all the interfaces have been connected, please turn on the water supply valve.

The Water supply valve should be prepared by the customer.

Prompt: If the toilet is narrow, and after installing the body, if it is difficult to install the water supply hose, the water supply hose can be installed into the body, and then the body is installed to the ceramic.

Acceptance of inspection items after installation completed

After the installation is completed, it must be commissioned and checked one by one according to the inspection items.

• Whether it can connect to a power outlet that can provide 120V to 60Hz and 15A safety ground or not.
• Whether the power plug is loose.
• Whether the main water supply valve of the water pipe is open.
• Whether each joint is tightened and fixed.
• Whether the power indicator lights up.
• Whether the functions of the product are normal:Whether the rear and bidet
• (including water pressure adjustment), dryer (including warm air intensity adjustment), water temperature and seat temperature adjustment, nozzle self-cleansing, automatic deodorization are normal.

Periodic spot inspection (please check once a month)

• Press the “Test” key to confirm that the indicator light goes out and confirm that the product will stop working.
• If there is no problem with the above content, press the “Reset” key and the product will restart.

Appearance in kind prevail

Note

1. Installed in cold weather, keep the product in a warm room for 2 hours before installation.
2. The company shall be not responsible for any accident or injury as it is installed not according to the method stipulated in installation instructions or the specified part is not used.

Failure analysis and processing

Fail To Work

• Please confirm: Whether a cloth cover cushion or other item is used on the sensing area of the seat ring. Solution: Remove the cloth cover or cushion or other items. Please confirm: Whether there is a power cut.
• Solution: Wait till the power is restored.
• Please confir m: Whether the plug is loose or in bad contact.
• Solution : Connect well the plug to ensure a good supply of power.
• Please confirm: Whether the power button is pressed. Solution: Press the power button of the toilet.

Washed Without Water

• Please confirm: Whether the water supply is cut off.
• Solution: Wait till the water supply is restored. Please confirm: Whether the inlet valve is open.
• Solution: Open the inlet valve.
• Please confirm: Whether the filter is blocked by dirt.
• Solution: Clean the filter.
• Please confirm : Whether the inlet hose is blocked due to bending.
• Solution: Restore the bending of the inlet hose.

Insufficient Cleaning Water

• Please confirm: Whether the water pressure is set at Low gear.
• Solution: Re-adjust the water pressure.
• Please confirm: Whether the filter is blocked by dirt. Solution: Clean the filter. Please confirm: Whether the water nozzle is blocked by dirt.
• Solution: Clean the nozzle.

Failure analysis and processing

Water Cut-off While Washing

• Please confirm: The machine will stop automatically in 4 minutes after pressing the Rear or Bidet button.
• Solution: Re-press the Rear or Bidet button.
• Please confirm : Whether left the seat while washing.
• Solution: Re-press Rear or Bidet button.

Water Temperature Is Not Hot Enough

• Please confirm : Whether the water temperature is set at Low or Normal Temp.
• Solution: Reset the water temperature.

Warm-air Temperature Is Not Hot

• Please confirm: Whether the air temp. is set at low gear or off status.
• Solution: Reset air temp. following the Remote-Con trol Instructions.

Air Cut-off While Dryer

• Please confirm: The machine will stop automatically in 4 minutes after pressing the Dryer button.
• Solution: Re-press the Dryer button.
• Please confirm: Whether left the seat while dryer.
• Solution: Re-press the Dryer button.

Seat Ring Temperature Is Not Hot

• Please confirm: Whether the seat ring Temp is set a Low gear or Turn-off status. Solution: Reset seat ring Temp following the
• Remote-Cotrol Instructions.
• Please confirm: Whether it is set at Economy status.
• Solution: Press the Economy button on the Control to exit the status.
• Please confirm: Whether there is a blackout.
• Solution: Wait till the power is restored.

Operation panel instructions

Stop

• It is used to stop the running function of the whole machine;
• Press and hold the “stop” key for more than 5 seconds when the seat is not in place to turn on/ off the power of the whole machine.

Rear/Move

• When sitting, press this key to start the function of “rear”;
• The cleaning time of this function is 4 minutes;
• When the cleaning function is on:
• Press the “rear” key again to turn on/ off the “reciprocating cleaning” function;
• Press the “position/\ V” key to adjust the cleaning position;
• Press the “water temp” key to adjust the water temperature;
• Press the “water pressure+/-” key to adjust the water pressure.

Bidet/Move

• When sitting, press this key to start the function of “bidet”;
• The cleaning time of this function is 4 minutes;
• When the cleaning function is on:
• Press the “bidet” again to turn on/ off the “reciprocating cleaning” function;
• Press the “position<>” key to adjust the cleaning position;
• Press the “water temp” key to adjust the water temperature;
• Press the “water pressure+/-” key to adjust the water pressure.

Dryer

• When sitting, press this key to start the “dryer” function;
• The dryer function is 4 minutes;
• When the dryer function is on:
• Press the “air temp” key to adjust the air temperature.

Water pressure
In the cleaning mode, press the “water pressure+/-” key to adjust the water pressure .The range of water preesure adjustment is 1-3.

Position
In the cleaning mode, press the “position< >” key to adjust the cleaning position. The pipe position adjustment range is 1-3 gears. It can be adjusted according to its body feeling. This function is only applicable to rear&bidet.

Air temp
In the dryer mode, press the “air temp” key to adjust the air temperature. The range of air temperature adjustment is 0-3 (0 is normal temperature). When the indicator lights are all off, the gear 0 is not heated.

Water temp
Used to adjust the temperature of water;
In the cleaning mode, press the “water temp” key to adjust the water temperature. The range of water temperature adjustment is 0-3 (when the water temperature is 0, it is not heated). When the indicator lights are all off, the gear 0 is not heated.

Seat temp
Used to adjust the temperature of the seat ring;
Press the “seat temp” key to adjust the seat temperature. The seat temperature adjustment range is 0-3 (when the seat temperature is 0, it is not heated). When the indicator lights are all off, the gear 0 is not heated.

Energy Saver /Night Light

• Energy Saver: Used to turn energy saving mode on / off. When on, the energy-saving indicator light on the machine is on.
  When it is turned on, the energy-saving mode will be automatically released when sitting, and it will be automatically restored to the energy-saving
  mode 10 minutes after leaving the seat.

• Night Light: Long press the “Energy Saver/Night Light” key for 3 seconds to turn on / off the night light function; when it is turned on, the white soft light at the bottom of the product will be on;Turn on for 10 minutes and then turn on or off automatically according to the brightness of the room.

Nozzle cleaning

• When you are not sitting, Press the “Bidet/Move+Stop” keys at the same time for more than 3 seconds to start the “nozzle cleaning” function.
• It is used for cleaning and maintenance of the cleaning pipe.
• After opening, the cleaning pipe stretches out. At this time, the cleaning pipe can be cleaned with a soft wet towel or a soft brush.

Function list

Note: “O” represents the configuration of this function. The function is based on the actual machine.

Basic Parameters

Note: test conditions: keep the ambient temperature at 20 °C, water inlet temperature within 14 – 16 °C, water inlet dynamic pressure at 0.2MPa, seat ring temperature at (high grade 3) , the water temperature at (high grade 3) , female cleaning water pressure at (high grade 3) , and an integral power of cleaning water from female cleaning mouth to the end (the above test conditions do not enter the hydraulic massage mode.)
Test method: set the seat temperature and water temperature to the non- heating mode, clean the water passage with a water temperature of 14-16 °C for 4 minutes, and then test the integral power according to the test conditions.
test conditions: water inlet temperature within 5 °C, water inlet dynamic pressure at 0.2MPa, seat ring temperature at (high grade 3) , the water temperature at (high grade 3) , female cleaning water pressure at (high grade 3), and an integral power of cleaning water from female cleaning mouth to the end .(the above test conditions do not enter the hydraulic massage mode.)
Test method: set the seat temperature and water temperature to the non- heating mode, clean the water passage with a water temperature of 5°C for 4 minutes, and then test the integral power according to the test conditions.

Maintenance instructions

Daily maintenance methods

Please remove the removable attachment before maintenance to make it more convenient for maintenance.
Precautions before maintenance:
CD Make sure that the power is in off state.

1. Do not allow water to enter the interior of the product during maintenance.
2. Make sure that the cleaned detergent is scrubbed to prevent it from sticking between the body of the product and the gap of the toilet.

Product surface maintenance

• Please unscrew the soft cloth after the soaking and use it again.
• If the surface of the product is dirty, use a neutral detergent for the bathroom. After dilution, wipe the product with a small amount of soft cloth, and immediately remove the residual detergent from the surface with a clean damp cloth.

When not used for a long time

1. The water supply valve to stop the inlet.
2. Then use a wet towel to seat the seat on the sensor, and then press the [rear key] or [bidet key] on the operation panel or the remote control repeatedly to use up the water in the internal waterway of the machine.
3. Disconnect the power.

Zhejiang Xingxing BianjieBao Co.,LTD.

• Address: Building A7, Hongjiaxingxing Electronic Industrial Park, Jiaojiang District, Taizhou City, Zhejiang Province, China
• Hotline: 400-601-7098

FAQ

Frequently Asked Questions

• Q: Can I adjust the water temperature on the bidet seat?
  • A: Yes, the bidet seat allows you to adjust the warm water temperature according to your preference.
• Q: Is the bidet seat easy to install?
  • A: The bidet seat comes with an installation guide that makes it easy to set up. If you encounter any difficulties, please refer to the manual or contact customer support.
• Q: How do I clean the bidet seat?
  • A: Use a mild detergent and soft cloth to clean the bidet seat. Avoid abrasive materials or harsh chemicals that may damage the surface.

Copyfish

OCR Result(Auto-Detect)

N/A

Translated(English)

N/A

Redo OCR Recapture Re-Translate Copy to clipboard

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>