Annecy 7.5Ft Pre Lit Flocked Pencil Christmas Tree Instruction Manual

Annecy 7.5Ft Pre Lit Flocked Pencil Christmas Tree

Warning

• The tree base MUST be placed on a flat rigid surface.
• This product is not intended for children to climb. Please keep your children from climbing this product.
• Do not place the product near the fire or heat sources! Caution Fire Hazard!
• Do not use corrosive cleaners for cleaning!
• Be careful of your hands when setting up! We recommend wearing protective gloves for assembly.
• Wires may come wrapped around frame pieces. Locate and unwrap wires before assembly.
• Disconnect from the mains supply while not in use. Please do not connect the chain to the supply while it is in the packing.
• Please check the number and condition of the parts according to the parts list. Please don’t hesitate to contact us if any parts are damaged or missing.
• We recommend checking the tightness of all connections between parts every six months.
• Risk of electric shock if lamps are broken or missing. Do not use.

The warning, cautions, and instructions listed in this manual may not cover all possible situations that may arise when using the product. Please contact us via e-mail contact@annecydesign.com if you need further information or help.

Article of decoration

All the diagrams are given for illustrative purposes only. According to the height of the Christmas tree you purchased. There may be variations from one model to another.

Warning

There are useless plastic caps on the end of each pole. Please make sure to remove them before assembling them.
If the caps were broken or missing, please don’t worry.

Assembly Instructions

step 1

1. Open the stand to a 90-degree angle until the hole on the tube matches (Fig 1).
   

2. Insert each eyebolt and begin threading clockwise for a couple of rotations only. Leave enough room for the tree pole to be inserted into the stand (Fig 2).
   

3. Place the tree stand in the desired location. Once the tree is fully assembled, it may be too difficult to move.

step 2

1. Locate the bottom section of the tree, which is marked “A”.
2. Remove the protective plastic cap from the end of the pole and place that end into the tree stand. Ensure the pole’s end reaches the bottom of the stand. (Fig 1)
3. Tighten the 3 eyebolts on the tree stand into the holes until the pole is secure. (Fig 2)
   

step 3

1. Locate the tree labeled “B” .Insert section “A”.
2. Locate the tree labeled “C” .Insert section “B”.
   

Note:
According to the height of the Christmas tree you purchased, our tree trunk may consist of two parts (A and B); or three parts (A, B, C).
We will mark each trunk section from the bottom to the top using “A-B-C” alphabetically. You will continue to build and connect each tree section upward using coaxial connectors or extension cords.

step 4

1. Please identify the corresponding connection points on each section of the tree trunk (A/B/C) where the light strings can be plugged in.
2. Align the flat ends of both connectors as shown and connect them together. Slide the screw cover from the “male” connector over the “female” connector and tighten.
3. Locate the corresponding connector on the light string controller harness and connect it to the transformer.
   

step 5

1. Open all the branches and leaves.
   To make the tree look full and natural, you can shape the branches row by row, starting from the inner tips and working outward. Take your time to manually expand the branches and fill the gaps between them for the desired effect.

2. Connect the power supply.

3. Press the light string control switch to access and explore various lighting modes and choose your favorite one.
   

DISASSEMBLY & STORAGE OF THE TREE

1. Unplug the ON/OFF foot pedal from the wall outlet.
2. To disconnect the sections, locate the connection-labeled light strings, unscrew the cap, and gently pull apart the light strings. There will be two or three connections depending on the size of your tree.
3. Lift each section straight up as you remove it from the section below. Gently fold the branches toward the center and place them in the storage container.
4. To close the tree stand for storage, unscrew all eyebolts and remove them from the stand. The tree stand will then fold together.
5. Keep the tree in a cool, dry location away from sunlight.

Attention! This package contains fragile items. Please handle this with care to avoid damage.
Caution! This product is unsuitable for children under the age of 3 due to small parts that can cause choking.
Warning! Not a toy. Watch out for pets or kids swallowing it.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>