HYDROMEISTER Rotatable Pull Out Bathroom Faucet Installation Guide
- June 17, 2024
- HYDROMEISTER
Table of Contents
Rotatable Pull Out Bathroom Faucet
“`html
Screw two mounting posts into another
two holes in the bottom of faucet body
Product Information:
Specifications:
- Material: Metal
- Finish: Chrome
- Installation: Deck-mounted
- Features: Pull-out hose, soap dispenser
Product Usage Instructions:
Installation Process:
-
Screw two water supply lines into faucet inlet holes in the
bottom of the faucet body. -
Screw two mounting posts into another two holes in the bottom
of the faucet body. -
Place an O-ring over the water supply lines and mounting posts
into the groove on the faucet base. -
From above, insert mounting posts and water supply lines
through the hole on the sink. -
From underneath the sink, secure the faucet body by placing a
plastic washer, metal washer, and mounting nut onto the mounting
post. -
Firmly tighten the mounting nut until the faucet is firmly
secured to the sink. -
Screw the mounting shank into the faucet base.
-
Attach weight to the pull-out hose using screws at the lowest
point on the pull-out hose. -
Ensure that the soap dispenser is attached to the sink by
mounting it with a mounting nut.
Using the Faucet:
-
To switch between natural state and pressing state, operate the
lever accordingly. -
To detach the pull-out hose, press the button of the quick
connector with fingers and pull down the hose.
Maintenance:
-
To remove the handle, unscrew the set screw from the handle and
detach it from the valve body. -
Connect the valve body with the water pipe and ensure it is
flush with the finished wall surface. -
Insert the shower arm through the flange and screw it into the
pipe elbow inside the wall.
FAQ:
How do I detach the pull-out hose?
To detach the pull-out hose, keep pressing the button of the
quick connector with fingers and pull down the hose.
How to limit the highest temperature of the pressure balance
valve?
The factory has fixed the highest temperature. No manual
adjustments are needed for this feature.
“`
Screw two water supply lines into faucet inlet holes in the bottom of faucet bodly.
Screw two mounting posts into another two holes in the bottom of faucet body.
Place a O-ring over water supply lines and mounting posts into the groove on the faucet base. From above insert mounting posts and water supply lines through hole on sink.
From underneath sink, secure faucet body by placing plastic washer, metal washer and mounting nut onto mounting post.
Firmly lightien mounting nut until faucet is firmly secured to sink.
Screw mounting shank into faucet base.
Screw two water supply lines into faucet intel holes in the bottom of faucet
body.
From above insert mounting shank and water supply lines through hole on sink.
From underneath, feed the plastic washer and mounting nut over the water
supply lines. Thread the mounting nut on to t he mounting shank. Tighten the
mounting nut to the underside of the sink.
Tighten the mounting nut retaining screw until faucet is firmly secured to
sink.
Attach weight to the pull-out hose using screws at the lowest point on the pull-out hose.
Attaching the pull-out hose.
Screw two water supply lines into faucet inlet tubes
Insert the faucet supply inlet tubes, water supply lines and mounting shank t hrough the hole in sink.
From underneath sink, feed the plastic washer, metal washer and mounting nut over the water supply lines, faucet inlet tubes, pul-out hose and mounting shank. Thread the mounting nut to the underside of the sink. Tighten the mounting nut retaining screws until faucet is firmly secured to sink.
Screw two water supply lines into faucet inlet tubes
natural state
pressing state
NOTE How to take off the pull-out hose: Keep pressing the button of quick connector with fingers. At the same time. Pull down the pull-out hose.
Keep pressing the button of quick connector with fingers. At the same time. Push the End of pull-out hose upward into the quick connector, until unable to push any futher. Pull the down the pull-out hose to ensure they connect well.
Ensure the soap dispenser to sink by mounting sink and mounting nut.
Ensure that plastic putty plate is pressed onto deck plate. Install the deck
plate over the holes in sink.
Insert the faucet supply inlet tubes, water supply lines and mounting shank
through the hole in the deck plate.
From underneath sink, feed the plastic washer, metal washer and mounting nut over the water supply lines, faucet inlet tubes, pul-out hose and mounting shank. Thread the mounting nut to the underside of the sink. Tighten the mounting nut to the underside of the sink.
Take off the red/blue button on the handle. Unscrew the set screw from. The handle. Take off the handle from the valve body.
Conect the value body with water pipe. Put them into wall so that front of the plasterguard is flush with the finished wall surface. Put plasterguard and Rubber ring onto value body.
Put the handle onto value body and tighten set screw. Insert the shower arm through the flange. Screw shower arm into pipe elbow inside the wall. Put the flange onto the finished wall surface. Thread shpwer head pntp shpwer arm.
There is a temperature adjust component can limit the highest temperature of
the pressure balance value. This factory had already fixed the highest
temperature to be <43.05 C. Due to water temperature & pressure devotions the
actual temperature must be checked by using a thermometer, please be carefully
to avoid scalding. T he highest temperature is 90. The lowest temperature is
3.9.
The temperature fall from ‘+’ to’-‘(Clockwise) We can adjust the maximum
temperature by this adjustment gear. The arrow on adjustment gear point the
maximum temperature desired. Determine maximum temperature desired and replace
the gear so that the slem can not move beyonf this point.
Make sure all inlets or outlets pipe were well connected, and the valve is closed Take off the red/green button on the handle. Unscrew the set screw from the handle. Take off the handle from the valve body. When the cartridge nut is in the valve body. the notch is hidden.
Then take off the temperature adjust component, please notice there is no need to remove the valve body. but by using a tool (such as a “-” screwdirect) to pry up the temperature adjust component directly.
Determine maximum temperature desired. Let the arrow on adjustment gear point the notch of maximum temperature desired on cartridge. Press down the adjustment gear onto cartridge.
1.Screw the handle body to the right until the handle off.
2.Screw the screw cover to the right until it off
Recommended component locations
Insert the shower arm through the flange. Screw shower arm into pipe elbow inside the wall Put the flange onto the finished wall surface. Thread shower head onto shower arm.
3.From underneath, get the valve body through the countertop
4.put the screw cover back and screw to the left until firmly secured, then firmly lighten the screw to the right by screwer.
Keep the handle pole static
The left-most
Screw the tub spout into pipe elbow inside the wall.
Pull this button upward dripping from tub spout
Pull this button upward dripping from shower head.
6.Screw the arrow part (show in picture to the left-most Put the left handle
in the same direction as the picture show, keep the handle pole static
meantime rotate the handle body to the right until firmly secured
Keep the handle pole static The right-most
Press this button down, dripping from shower head.
Pull this button down dripping from tub spout
6.Screw the arrow part (show in picture to the right-most Put the right handle in the same direction as the picture show, keep the handle pole static meantime rotate the handle body to the right until firmly secured
5.Install the left and right handles Please refer to the detail instruction in the page of The installation of spit-handle”
Pressing State
Keep pressing this button of quick connector with fingers. At the same time,
Push the End of pull-out hose upward into the quick connector, until unable to
push any further. Pull down the pull-out hose to ensure they connect well.
6.Connect the flexible hoses: the side with nut connect to TEE the other side to the valve body.
1.Confirm the O-ring is underneath the faucet. If you bought drain together with the faucet, plesse put the pop-up pole through the hole which in at back of the faucet.
Rubber washer Stainless Steel washer
2.From underneath feed the washers and mounting nut. If you also bought drain,please also gel the pop-up pole through the washers before Screwing the mounting nut.
7.The installation reference image for the faucet without drain
Tighten the screw to Connect the Pop-up pole with the fully-installed drain.
Install the drain as the picture shows
The installation reference image for the faucet with drain.
3.Screw the mounting nut to right until it is firmly secured 4.Screw the nut of the TEE joint to right until the TEE is Armly secured.
Floor standing faucet installation instructions
1.confirm the O-ring is underneath the faucet
Rubber washer Stainless steel washer
3.Screw the mounting nut to right until it is firemly secured
4. Install the left and right handles Please refer to the detail instruction
in the page of “The installation of spilt
1.Get the hose of shower head through the shower bracket and locate them on the countertop. From undemeath Saed the washers and mounting that Screw the mounting nut to fight until this firmly secured.
(1)Before installation, ensure there’s one (2)install the faucet with inlet
hoses and fixing hole (@32-040mm) in the basin, remove screw into the basin
hole, make the focation the faucet bottom’s fixation part, put the parts
connect with the foxing screw from basin O-ring washer to the bottom of the
faucet. bottom, screw down the nut, and fix the faucet
on the basin.
(1) Before installation, ensure there’s one hole (032-040mm) in the basin. Put the O-ring washer under the bottom of the faucet body.
(2) Install the faucet body with (3) Connect the two hoses with
inlet hoses and screw bolts
cold and hot water angle valve
into the basin hole, make the separately.
fixation parts connect with the
screw bolts, screw down the
nuts.
(4) Turn on the water supply, check all connect points if leakage. If leaking, tighten it. (5) Now the faucet is ready for using.
This installation steps is applied to one hole bathroom faucet with two screw bolt, for example:
Conector Tighten 3 screws in the mounting nut by screwers une the shower bracket is firmly secured Then connect another site of the shower hose to the valve body.
(3) Use wrench to screw down the nut, than use cross screwdriver to screw down the two screw to strengthen the fixed dynamics.
(4) Connect the two hoses with cold and hot water angle valve separately
Step 1:Connect the brass adapter provided to water supply line. Step 2:Adjust
lever and distance to fit faucet body. Step 3: Turn water valve on for a while
to let the dust and impurities out. Step4: Assemble the shower set. Step
5:Place pre-assembled shower in the wall to find proper position and then mark
the mounting hole need to be drilled.
Step 6:Drill a hole for the upper part shower bar bracket, screw it. Step
7:Place the decoration cover to the brass adapters. Step 8:Install the pre-
assembled shower to the connections. Step 9:Connect shower hose, handheld
shower and rain shower head.
7.Connect the flexible fuses as the picture shows.
1. Put up the faucet handle to the right side, then cold water out more, to the left side, the hot water out more. 2. The exchange switch is between faucet and hand shower to the left is for hand shower water out, and to the right is for the faucet water out. 3. Put 3 to 4 4. Fix 5to 4. 5. Tighten 6 to 7. 6. Lock 4 to 7. 7. Connect inlet water pipe to water soutle, the left connect hot water, the rightconnect cold water. 8. Fix the floor standing faucet to the floor with bolt 9. Connect the hand shower and hose.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>