iCleaningo DC01 Bidet Toilet Seat User Manual
- June 17, 2024
- iCleaningo
Table of Contents
DC01 Bidet Manual
Please read this product manual in detail before installation and use.
Parts Names
Remarks: the appearance and function of the product shall prevail
in kind.
Packing List
※Please check if all items are included in the package. If anything is
missing, please contact customer service.
※The pictures of the above items are for reference only and are subject to the
real thing.
Installation Instructions
Water Pressure Check
- Minimum required water pressure : 11.6 PSI (0.08 MPa)
- Maximum water pressure : 108.78 PSI (0.75 MPa)
Failure to meet minimum water pressure prevents optimal cleaning results
Mounting Dimension Check
Bdet Installation as shown below:
Make sure there is enough space in the bathroom.
Installation Steps
-
Installation Nuts
Insert nuts into the mounting holes. -
Installation Mounting Plate
Slide the mounting bolts over the adjustable bracket and screw in the nuts. (Note: Anti-skid blocks face up)
Caution
“When the nut cannot be installed into the mounting hole on the ceramic
toilet, you can use a wing nut for installation.”
3.Installation Bidet
Push the bidet flat into place and the catch will lock automatically. If you
find that the bidet seat does not match the position of the ceramic toilet,
you can solve the problem by adjusting the mounting plate position. Just press
and hold the removal button on the side to pull out the main unit, loosen the
mounting bolt to adjust the position and then lock it again.
Installation Water Hose Fittings
- Install the T-Valve to the toilet tank and connect the shutoff valve to the T-Valve through the toilet water supply hose.
- Connect the bidet to the T-valve via the Inlet hose.
Water supply testing
- Turn the shutoff valve counterclockwise to open it to the maximum.
- Make sure there is no water leakage from each connection part.
※If there is water leakage, please re-tighten the nut class for re- installation.
WARNING
To avoid product leakage and other phenomena, please follow the correct
installation method.
If the house has not been used for a long time or has been newly renovated,
please drain the sewage from the pipes before connecting the water supply
fittings to avoid damage to the parts.
Power supply testing
- Insert the power plug into an AC 120 volt socket.
- Confirm whether the power is connected
(1) Make sure the blue light on the control panel is on.
When the machine is powered on, the blue light blinks to indicate that the seat is heating up.
Various Operations
STOP
- Short press to stop all washing and drying functions currently running.
- When the bidet seat/lid is fully erected, press briefly to close the seat, press again to close the lid.
FRONT
- When seated, short press initiates front-to-back oscillate ing cleaning. Pressing again will stop the oscillation.
- The cleaning cycle lasts for 3 minutes. During the cleaning process, adjustments can be made to the cleaning intensity, nozzle position, water temperature (cold or hot) using the corresponding buttons.
REAR
- When seated, short press initiates front-to-back oscillating cleaning. Pressing again will stop the oscillation.
- The cleaning cycle lasts for 3 minutes. During the cleaning process, adjustments can be made to the cleaning intensity, nozzle position, water temperature (cold or hot) using the corresponding buttons.
HANDHELD
- When there is no cleaning action: Briefly press to turn on, press again briefly to turn off.
- The cleaning cycle lasts for 3 minutes.
DRYER
When seated, press briefly to start the warm air drying function. Press again
to switch to high-speed mode, which cycles in the sequence of “Low-High-Low”.
The drying cycle lasts for three minutes. During drying, you can adjust the
air temperature.
RADAR(Auto Open Lid/Seat)
-
Female mode: The bidet lid automatically opens when someone approaches, closes 3 minutes after they leave.
Male Mode: The bidet lid/seat automatically opens when someone approaches, closes 3 minutes after they leave.
Default mode at startup: Female mod.
Press and hold the radar button for 1 second to switch to Male mode. -
Short presses adjust the radar sensitivity. The microwave radar sensitivity can be set to Low, Medium, High, or turned off. When turned off, the microwave module is deactivated. The default setting is Medium.
-
The indicator light corresponds to the sensitivity setting, with a beep sound indicating the setting: Off ‘Dong’, Low ‘Dong’, Medium ‘Dong Dong’, High ‘Dong Dong Dong’. These correspond to the sensitivity levels in sequence.”
PRESSURE
- When cleaning, short press to open, can realize “low – medium – high” 3-stage cleaning intensity cycle adjustment.
- Default medium grade, high grade is pressurized strong cleaning.
H-C/NOZZLE/MUTE
H-C:During cleaning, a short press initiates the alternate cold and hot
cleaning. Pressing again will stop this function.
NOZZLE:Short press to start the nozzle clean function in the off-seat state,
and the cleaning tube is all extended.
MUTE: Long press 1 second to switch to silent mode. Long press again for 1
second to switch to the sound mode.
POSITION
- Short press to open when cleaning, can realize “1-2-3-4-3-2-1” 4 gear position cycle adjustment.
- Default middle gear.
CHILD
- Ignore the state of the seat, long press 1 second to start the child cleaning function, short press again to close the child cleaning or cleaning 60 seconds after the automatic stop.
- In order to ensure safety, children please use this product reasonably under the help and guidance of parents, and it is not recommended to use it for young children under 5 years old.
FLUSH/LIGHTT
- Short press to start the automatic flushing function. (Optional auto-flush kit is required)
- Long press 1 second can cycle switch night light mode, the default mode is microwave sensor night light.
(Sensing people close to the night light will turn on, people leave 30 seconds after the extinction)
●Microwave sensor night light mode – always on mode – off night light mode.
WATER TEMP
- Short press to turn on the cycle adjustment, the default middle gear on the power on.
(low-middle-high-middle-low-off gear) cycle in turn.
Temperature adjustment range: about 91.4-104 °F （33~40°C）。
DRYERTEMP
- Short press to turn on the cycle adjustment, the default middle gear on the power on.
(low-middle-high-middle-low-off gear) cycle in turn.
Temperature adjustment range: about 98.6-140 °F（35~60°C）。
SEAT TEMP
- Short press to turn on the cycle adjustment, the default middle gear on the power on.
(low-middle-high-middle-low-off gear) cycle in turn.
Temperature adjustment range: about 86-104 °F（30~40°C）。
All beeps correspond to: low: “dong”
Medium grade: “dong dong”
High grade: “dong dong dong”
Super high grade: “dong dong dong dong”
The gear light only applies to water temperature, seat temperature and air
temperature：
From L to H: Low-Medium-High.
※Flush function is optional: auto-flush kit is required.
Remote Control Battery Replacement
- Turn counterclockwise to remove the battery cover.
- Remove the silicone waterproof cover.
- Remove the dead battery: push the sheet metal part outward while snapping the battery upward.
- To install a new battery: Insert the battery into the sheet metal part side first, then press down on the plastic sheet side.
Remote Control
- When seated , short press can stop all the current running functions.
2. When no one is seated: short press to open the cycle adjustment, open bidet lid—open bidet seat——closed bidet lid——closed bidet seat automatic flush .
NOTE: The automatic flush function can only be used after the optional flush kit is installed.
Remote Control Pairing
(pairing required for first time use)
Disconnect the toilet seat’s power for 30 seconds. Then, press and hold the
remote control for 5 seconds to restore power to the toilet seat. Upon hearing
a beep, the pairing is successful.
- It is recommended to place the remote control horizontally on the table.
- If you want to place the remote control vertically, peel off the adhesive backing on the bottom of the remote control and stick it on the surface to which it is to be attached.
select a surface that is easy to adhere to. (Wooden products, frosted tiles, etc.)
※Do not pour water on the remote control when cleaning, as it may lead to short-circuiting of the product.
Adjusting the Handheld Bidet Sprayer:
- The shape of the splash is tapered.
- Counterclockwise rotation of the Spray-Head out of the water splash gradually become linear.
※(When adjusting the water splash to a straight line, stop rotating the Spray- Head to prevent water leakage and dropping of the Spray-Head.)
Cleaning & Maintenance
Caution
- Before maintenance, please cut off the power, close the shutoff valve, and stop the water supply. It is strictly prohibited to rinse the product with water during maintenance.
The bidet will automatically drain itself every 48H to ensure clean water inside the product.
Maintenance of filters
When you notice that the cleaning intensity is weakening, clean the filter
promptly. Be sure to turn off the shutoff valve when disassembling the filter,
and when installing the filter, tighten it firmly to avoid water leakage.
※Recommended cleaning once every 1-2 months.
Winter Frost Protection
（Ambient temperature below 39.2 ℉）
In cold winter conditions, after long-distance transportation or extended storage, there might be residual water inside the product that could freeze. To prevent damage caused by freezing, take the following anti-freezing measures:
- Place the product in a warm indoor environment for 30 minutes to allow it to naturally thaw before resuming water and power supply.
- If freezing occurs and the water cannot be sprayed, cover the toilet’s water supply hose or the connection point with a cloth soaked in hot water to assist in thawing.
- For long periods of non-use, please shut off the water supply angle valve.
Caution
- Do not pour hot water or blow hot air on the water supply hose of the Bidet, as this may cause rupture of the water supply hose.
- Do not connect the power supply until the inside of the toilet seat is thawed out, otherwise it may cause electric shock and fire.
Warnings
Do not add water or detergent to the inside of the Bidet.
※Otherwise, there may be a risk of electric shock and fire.
Cleaning and Maintenance of Seat, Seat Cover and Others (Plastic Parts)
- Please wipe the product with a soft, damp cloth.
Failure to promptly clean dirt may make it harder to clean. Please regularly wipe with a soft, damp cloth.”
Nozzle cleaning
In the off-seat state, short press the nozzle button, the cleaner nozzle will
automatically extend. If there is dirt in the nozzle hole, you can gently hold
the cleaner with one hand and clean it with a toothbrush with the other hand,
and then press any key when finished, the cleaner will retract.
※Do not exert too much force or the nozzle will be damaged.
※The maximum time for extending is 3 minutes, after that the nozzle will
retract automatically.
Troubleshooting
Trouble Please Check
Toilet bidet lid/seat won’t open automatically| Is the auto-sensing function
turned off ?| Refer to the manual to adjust radar sensing
---|---|---
The dryer temperature is low| Is the dryer temperature set to low level?|
Refer to the instruction manual to adjust the air temperature
The cleansing water is cold| Is the warm water temperature set to “OFF” or a
low level?| Refer to the instruction manual to adjust the water temperature
When the temperature of the water supply or the bathroom is low, the water
temperature may be low when first sprayed.|
the cleansing water does not come out| Has a water failure occurred?| Press
“Stop” button on the control panel and wait until water service is restored.
Is the shutoff valve closed?| Fully open the shutoff valve
The bidet seat is cold| Is the filter clogged with foreign matter?| Clean the
filter
Is the bidet seat temperature set to “OFF” or a low level?| Refer Temperat
rection manual to adjust the seat
Have you been seated for a long time?| After about 20 minutes of sitting, the
temperature starts going down, and after about 1 hour, the toilet seat heater
is turned “OFF” x Stand up from the seat and then use again
Specifications
| Rated power supply | AC120V 60Hz |
|---|---|
| Rated Power Consumption | 1060W |
| Type of water heater | Instant heat type |
| Power Cord Length | 4.92ft (1.5m) |
| Water protection level | IPX4 |
| Cleansing | Spray |
| Volume | Rear Cleansing |
min)<at 29 PSI (0.20 MPa) water pressure>
Front Cleansing| Approx. 0.08-0.13 gal / min (Approx. 0.3-0.5 L / min)<at 29
PSI (0.20 MPa) water pressure>
Water Temp| Adjustable temperature range : OFF, about 91.4-104 °F (about 33-40
°C)
Heater capacity| 1500W
Safety Device| Temperature Fuse/thermostat
Backflow prevention device| Vacuum breaker, Check valve
Heated seat| Surface temperature| Adjustable temperature range : OFF, about
86-104 °F (about 30-40 °C)
Heater capacity| MAX5OW
Safety Device| Temperature Fuse
Warm air dryer| *Warm air temp| Adjustable temperature range : about 95-140 °F
(about 35-60 °C)
Airflow volume| Approx. 6.36-11.3 ft3 / min (Approx. 0.18-0.32 m3 / min)
Heater capacity| MAX500W
Safety Device| Temperature Fuse
Water supply pressure| Minimum required water pressure : 11.6 PSI (0.08 MPa)
★Temperature around the warm air outlet measured by icleaningo.
Safety Precautions
WARNING
Do not plug or unplug the power plug with wet hands.
-
Doing so may cause electrical shock.
Do not get any water or cleaning solution on the main unit or power plug. -
Doing so may cause fire, electrical shock, heat or short circuit.
-
Doing so may cause the product to crack resulting in injury or water damage.
Never disassemble, repair or alter.
Doing so may cause fire, electrical shock, overheating, short circuit or
breakdown.
Do not install the product on moving vehicles such as wheeled vehicles or
boats.
-
Doing so may cause fire, electric shock, short circuit or malfunction.
-
The toilet seat, toilet lid, main unit, or other parts may come loose and fall off, resulting in injury.
Do not use the product if a malfunction occurs. -
In case of breakdown or other problem, be sure to cut off power by means such as unplugging the power plug.
Close the water shutoff valve to stop water supply.
Possible malfunctions:
-
Water is leaking from a pipe or the main unit.
-
The product is cracked or broken.
-
The product makes a strange noise or emits a strange odor.
-
The product emits smoke.
-
The product is abnormally hot.
-
The toilet seat cushion is out of place.
-
Continued use after malfunction could cause a fire, electric shock, heat, short circuit, injury or water damage.
Do not use other water then allowed by the laws and ordinances of the region of use. Only Use drinking water.
Do not use seawater or recycled water. -
Doing so may cause irritation to the skin and malfunction.
Do not touch the power plug during thunderstorms. -
Doing so may cause electrical shock.
Do not allow the water supply hose to touch the power plug or outlet. -
Doing so may cause condensation resulting in a fire, electrical shock, heat or a short.
Do not do anything that may damage the power cord, power plug.
Do not strike, yank, twist, excessively bend, damage, alter, or heat the power cords.
Also, do not place anything heavy on, bind or pinch the power cords. -
Using a damaged power cord may result in a fire, electrical shock, heat or short.
Do not use a loose or faulty electrical outlet. -
Doing so may cause fire or short circuit.
Do no use any outlet or wiring equipment beyond its specified rating. -
Plugging too many plugs into the same outlet, for example using outlet splitters, can cause fire due to heat.
Do not use any power supply other than the one specified.
AC 120 V, 60 Hz -
Doing so may cause fire or excessive heat.
Do not stick a finger or anything else into the warm air outlet.
Do not place anything on the warm air outlet or drape clothes over it. -
Doing so may cause burns, electrical shock or malfunction.
Keep cigarettes and other open flames away from the product. -
Failure to do so may cause fire.
Refrain from sitting on the seat for long periods. -
It may cause low-temperature burns.
To prevent the following persons from getting a moderate temperature burn during use, other person should turn off the toilet seat heater. -
Young children, the aged and other users unable to set the temperature appropriately themselves.
-
The ill, physically disabled and others who do not have freedom of movement.
-
Those using any medicines that cause drowsiness (sleeping or cold medicine), those who have been drinking heavily, anyone severely fatigued and anyone else liable to fall asleep.
This is an electrical product. Do not install it anywhere water is likely to get on the product or anywhere with humidity high enough that water is likely to form on the surface of this product. When using the product in a bathroom, install a fan or ventilation port and ensure good air flow through the bathroom. -
Failure to do so may cause fire or electrical shock.
Always connect the product to the cold water supply. -
Connecting to hot water supply may result in burns and equipment damage.
Make sure that a properly grounded (3 prong) outlet has been installed. -
Failure to install a grounded outlet could cause electrical shock in the event of a malfunction or short circuit.
Insert the power plug securely into the outlet. -
Failure to do so may cause fire, heat or short circuit.
To unplug, hold the power plug, not the power cord.
Do not unplug by pulling the power cord. -
Pulling on the power cord may cause damage and result in fire or heat.
If the power cord is damaged, avoid danger by having the manufacturer’s repair department or equivalent specialist replace it.
Always unpug the power plug from the outlet before maintenance or inspection. -
Failure to do so may cause electrical shock or malfunction.
Periodically remove dust and dirt from the power plug and make sure it is securely plugged into the wall outlet. -
Failure to do so may cause fire, heat or short circuit.
Pull the power plug out from the outlet and wipe clean with a dry cloth.
Always unplug the power plug from the outlet before removing the main unit. -
Failure to do so may cause fire or electrical shock.
Preliminary studies in females suggest that overuse of continuous spraying can
increase the possibility of vaginal mucosa drying and potential reduction in
desirable microbial organisms.
Although these studies have not been validated, please consult your healthcare
provider for concerns regarding whether these circumstances may apply to you.
More importantly, if you are an individual suffering from any immune
deficiency as a result of disease, chemotherapy, or other medical condition
compromising the immune system you should consult your healthcare provider
before use of this product.
CAUTION
Do not use the product if the main unit is unstable.
-
Doing so may cause the main unit to come loose and fall, resulting in injury.
If the product is damaged, do not touch the damaged section. -
Doing so may cause electrical shock or injury.
-
Replace it immediately.
Do not apply strong force, mechanical shock, step on or stand on the toilet seat, toilet lid or main unit. Also do
not place any heavy object on the toilet seat, toilet lid or main unit. -
Doing so may cause cracking or cause the main unit to come loose and fall, resulting in injury.
-
Doing so may damage the product and cause injury or water damage.
Do not lift up this product by the toilet seat or lid.
Do not raise the toilet seat or lid while objects are resting on top of the unit. -
Doing so may cause the main unit to come loose and fall, resulting in injury.
When maintaining the plastic parts (main unit etc.) or the water supply hose, use a neutral kitchen detergent
diluted with water. Do not use any of the following.
Toilet cleaner, household cleaner, benzene, paint thinner, powdered cleanser or nylon scrubbing brush. -
These items may damage or crack the plastic and cause injury or malfunction.
-
These items could damage the water supply hose and cause a water leak.
To prevent a sudden water leak, do not remove the water filter drain valve when the shutoff valve is open. -
Doing so will cause water to spurt out.
(Refer to Page 34 for instructions on cleaning the water filter drain valve.)
Do not fold or crush the water supply hose; do not damage by cutting with a sharp object. -
Doing so may cause water leaks.
Do not install the base plate, which is not attached. -
Doing so may cause damage
If a water leak should occur, always close the shutoff valve.
When the ambient temperature is likely to drop to 32 °F (0 °C) or lower, prevent damage to the pipes and hoses due to freezing -
Frozen water pipes could cause the main unit and the pipes to break, resulting in a water leak.
-
Regulate the room temperature to prevent the pipes and hoses from freezing during cold months.
-
Drain the water.
When not using the product over an extended period of time, drain the water out of the main unit and the water supply hose after closing the water shutoff valve, and pull the power plug from the outlet. -
When using the product again, allow the product to refill with water first. Otherwise, the water in the tank might become contaminat ed and cause skin inflammation or other problems.
-
Leaving the power on may cause fire or heat When installing the water filter drain valve, make sure that it is securely tightened in its proper position.
-
Failure to securely tighten it may cause a water leak.
Push the main unit securely on to the base plate. -
After pushing the main unit until a click sound is heard, pull it slightly toward you to make sure that the product does not detach.
-
Doing so may cause the main unit to come loose and fall, resulting in injury.
DANGER
To reduce the risk of electrocution：
- Do not use while bathing.
- Do not place or store the product where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- Do not reach for the product when it has fallen into water. Unplug it immediately.
WARING
To reduce the risk of burns, electrocution, fire or injury to persons:
- Close supervision is necessary when this product is used by, on, or near children orinvalids.
- Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, is not working properly, has been dropped or damaged, or has been dropped in water. Return the product to a service center for examination and repair.
- Keep the cord away from heated surfaces.
- Never block the air openings on the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair,and other similar items.
- Never use while sleepy or drowsy.
- Never drop or insert any object into any opening or hose.
- Do not use outdoors. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- Connect this product to a properly grounded outlet only.
- The tank should be filled with water only.
Limited Warranty
-
The product as a whole comes with a 1-year limited warranty, which covers free repairs for any quality issues with the product itself.
Damages resulting from improperimproper installation or misuse are not covered under the free warranty. -
This limited warranty is extended only to the ORIGINAL PURCHASER of the product and is not transferable to any third party, including but not limited to any subsequent purchaser or owner of the product. This warranty applies only to Icleaningo product is purchased and installed in USA.
-
Iclaningo’s obligations under this warranty are limited to repair, replacement or other appropriate adjustment, at Icleaningo’s option of the product or parts found to be defective in normal use, provided that such product was properly installed, used and serviced in accordance with instructions.
This warranty does not apply to the following items:
a) Damage resulting from natural disasters and acts of God, such as fires, earthquakes, floods, lightning, storms, etc.
b) Damage resulting from accidental incidents, improper use, misuse, abuse, negligence, inadequate maintenance, or improper care.
c) Damage caused by sediment or foreign objects in the water supply system or water quality.
d) Damage caused by improper installation or placing the product in harsh and/or hazardous environments.
e) Damage resulting from improper disassembly, repair, or modification of the product.
f ) Loss or damage caused by using wires and plugs not provided by the factory, using loose or faulty power outlets, or using non-GFI (Ground Fault Interrupter) outlets for 120V, 60Hz current.
g) Damage resulting from normal and customary wear and tear.
NOTE : The use of a high concentrate chlorine or chlorine related products can seriously damage the fittings.
To protect your rights, kindly preserve the warranty certificate and use the packaging box for secure product transportation during shipping. We recommend keeping the packaging box for at least 30 days from the date of receipt.
iCleaningo Company Limited
Address ： Changsha, Hunan CHINA
Zip code ：410000 Email
：support@icleaningo.com
Websites ：www.icleaningo.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>