havit HV1107MR16T Tivah 5W 12V DC Fixed LED Wall Pillar Light Instruction Manual

: June 4, 2024
: havit

Table of Contents

Product Specifications
Important Safety Issues
Steps for Installation
Steps for Changing Globe
Must be installed by a licensed electrician
Read User Manual Online (PDF format)
Download This Manual (PDF format)

havit HV1107MR16T Tivah 5W 12V DC Fixed LED Wall Pillar Light

Product Specifications

Model No.| HV1107MR16T| HV1117MR16T| HV1127MR16T| HV1137MR16T| HV1147MR16T| HV1177MR16T| HV1187MR16T| HV1197MR16T
---|---|---|---|---|---|---|---|---
Name| Tivah
Material| 316 Stainless Steel| Solid Copper| Aluminium| Aluminium| Aluminium| Solid Brass| Aluminium| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Graphite| Titanium| Antique Brass
IP Rating| IP65
Input Voltage| 12v DC (Requires external power supply)
Lamp Base| MR16
Lamp Wattage| 1x 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 270lm, 285lm, 300lm
CRI| > 80
Dimmable| No (not with globes supplied)
Warranty| 3 Years Replacement*

Important Safety Issues

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globes:: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
Aluminium and 304SS fittings must not be installed within 5km of any salt water environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements. Please visit website for most current installation instructions.

Steps for Installation

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen allen screws on side of base and separate mounting bracket from fitting.
Install the backing plate securely using appropriate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void warranty.
Connect the cable – Connect live and neutral wire to a suitable 12v DC LED Driver – when connceting more than 1 fitting, Wiring must be done in Parralel
(DO NOT CONNECT DIRECTLY TO 240V POWER)
Affix the fitting to the mounting bracket and tighten allen screws, making sure these are tight to avoid any water penetration.
Apply silicon seal around the whole base plate to avoid any water getting into electrical connections.
Colour temperature and wattage is preset to 3000k, to change remove cover from fitting by twisting anti clockwise and set aside. Remove globe and select desired colour temperature by moving switches on side of globe and reinsert globe into lampholders.
Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globe

Remove the cover by twisting anti-clockwise and set aside, remove globe by holding on the outer rim of the globe and gently pull.
Re-insert the appropriate globe by inserting the 2 pins into the lampholder and gently push down.
(Make sure not to exceed max wattage, see product label for correct info)
Reattach cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.