HOTWHEELS HTP15-MA70 Monster Trucks Instructions

: June 17, 2024
: HOTWHEELS

Table of Contents

HOTWHEELS HTP15-MA70 Monster Trucks
Product Information
Product Usage Instructions
CONTENTS
FEATURES
INSTALLATION SET UP
HOW TO DRIVE
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HOTWHEELS HTP15-MA70 Monster Trucks

HOTWHEELS-HTP15-MA70-Monster-Trucks-PRODUCT

Product Information

Specifications
- Model: HTP15-MA70_I/S_21A
- Size: 27.5 x 18
- Required Flyer Sheets: 24S_RC_HTP15-MA71_21A_IS (or later), 24S_RC_R0000-MA70_21A_Battery_Flyer_G3 (or later)
- Age Recommendation: 4+

Product Usage Instructions

Changing Batteries in Remote Controller:
- Unscrew the battery cover using a Phillips head screwdriver (not included).
- Install 2 AAA (LR03) 1.5V alkaline batteries (not included) with polarity (+/-) as indicated inside the battery compartment.
- Replace the battery cover and tighten the screw.
- If the LED on the remote controller does not light up during play or if the vehicle does not respond well after recharging, replace the batteries.
Charging Instructions for Vehicle:
- The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery and must be fully charged before first use.
- Slide the power switch to OFF (0/).
- Open the charge cord cover.
- Connect the charge cord to a 5V/2A USB power adapter (not included).
- Charging will begin when the cord is connected. A red LED on the vehicle will indicate that charging is in progress.
- The LED will turn green but remain on for a while when the vehicle is fully charged.
Frequently Asked Questions:
- Q: What type of batteries does the remote controller use?
- A: The remote controller uses 2 AAA (LR03) 1.5V alkaline batteries.
- Q: How can I tell if the vehicle is fully charged?
- A: The LED on the vehicle will turn green and remain on for a while when the vehicle is fully charged.

FEATURES

$HOTWHEELS-HTP15-MA70-Monster-Trucks-FIG-1 $2$$

BOTTOM VIEW

$HOTWHEELS-HTP15-MA70-Monster-Trucks-FIG-1 $3$$

A. LED INDICATOR
B. DRIVING CONTROLS
C. BATTERY BOX
D. STEERING ALIGNMENT
E. CHARGE CORD COVER
F. POWER SWITCH
G. LED INDICATOR
H. CHARGE CORD

INSTALLATION SET UP

A. REMOTE CONTROLLER BATTERY INSTALLATION

Unscrew the battery cover with a Phillips head screwdriver (not included).
Install 2 AAA (LR03) 1.5V alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries.
Replace the battery cover and tighten the screw.
Replace batteries in the remote controller if the LED on the remote controller does not go on during playing or if the vehicle does not respond well after a recharge.

B. CHARGING THE VEHICLE

The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged before first use.

Slide the power switch to OFF (0/ ).
Open the charge cord cover.
Connect the charge cord to a 5V/2A USB power adapter (not included).
Charging will begin when the cord is connected. A red LED on the vehicle will be on as the vehicle is charging.
The LED will turn green but remain on for a while when the vehicle is fully charged. Unplug the charge cord when charging is complete. A full charge will usually take approximately 120 minutes. Charging time may vary.
Close the charge cord cover.
Recharge the vehicle if the vehicle begins to run slowly or does not respond.
- NOTE: The power switch must be in the OFF (0/ ) position when charging the vehicle. $HOTWHEELS-HTP15-MA70-Monster-Trucks-FIG-1 $6$$
- Red
- Vehicle is charging
- Green
- The vehicle is fully charged

TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before recharging the vehicle.

C. PAIRING THE REMOTE CONTROLLER AND VEHICLE

Slide the power switch to ON (I) on the vehicle.
Push the remote controller’s driving control joystick forward/backward after switching on the vehicle.
Pairing is complete when the LED changes from flashing red to solid red on the remote controller.
- NOTE: If the vehicle does not respond to the remote controller after pairing, switch the vehicle off and then back on to try pairing again or replace the batteries in the remote controller if the batteries are drained.
- Pairing
- Pairing is complete

TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To resume normal play, slide the vehicle’s power switch to OFF then ON again, and then push the remote controller’s driving control joystick forward/backward to pair the vehicle and remote controller.

D. STEERING ALIGNMENT

Check the vehicle’s steering alignment before playing by driving it forward to see if it is driving straight.
If the vehicle automatically steers toward the right/left, turn the steering adjuster dial to the opposite direction and adjust until it runs in a straight line.

HOW TO DRIVE

CHECKLIST

Is the vehicle fully charged?
Is the remote controller equipped with fresh batteries?
Is the remote controller paired with the vehicle?
Has the vehicle’s steering been aligned?

CONTROLS

$HOTWHEELS-HTP15-MA70-Monster-Trucks-FIG-1 $11$$

SKILL CHECK! Remember, steering directions are flipped on the remote controller when you are driving backward!

NOTE: The operating range of the remote controller is up to 30 m (98 ft).

WHEELIE ACTION

Set up a wheelie! $HOTWHEELS-HTP15-MA70-Monster-Trucks-FIG-1 $12$$

GLOW-IN-THE-DARK

Place the vehicle near a light.
Glows in the dark!
- Place the vehicle approximately 152 cm (5 feet) away from a light source for approximately 30 seconds.
- Placing the vehicle closer will not intensify the “glow-in-the-dark” feature.
- The glow-in-the-dark feature will last longer if you do not expose this product to intense heat or direct sunlight for prolonged periods.

STORAGE

Store the remote controller under the vehicle.

Adult supervision is recommended when the vehicle is being operated. Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle. HOTWHEELS.COM.