Servis S8351B Washing Machine Instruction Manual

: June 17, 2024
: Servis

Table of Contents

INSTALLATION INSTRUCTION
Installation
Adjusting the feet
Preparation
Operating the product
Programme and consumption table

Servis S8351B Washing Machine Instruction Manual

INSTALLATION INSTRUCTION

Important instructions for safety and environment

This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty.

General safety

This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product.Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children of less than 3 years should be kept away unless continuously supervised.
Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent. There is the risk of electric shock!
This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see “Cancelling the programme” section.
Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect tohave the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.
The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.
Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.
Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get damaged.
Unplug the product when not in use.
Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!
Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug.
Use detergents, softeners and supplements suitable for automatic washing machines only.
Follow the instructions on the textile tags and on the detergent package.
The product must be unplugged during installation, maintenance, cleaning and repai- ring procedures.
Always have the repairing procedures carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designa- ted by the importer in order to avoid possible risks.
Place the product on a rigid, flat and level surface.
Do not place it on a long-pile rug or similar surfaces.
Do not place the product on a high platform or near the edge on a cascaded surface.
Do not place the product on the power cable.
Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces.
The water supply pressure required to run the product is between 1 to 10 bars (0.1 1MPa)
Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.
Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.
1.2 Intended use
This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.
The product must only be used for washing and rinsing of laundry that are marked accordingly. • The manufacturer waives any responsibility arisen from incorrect usage or transporta- tion.
The service life of your product is 10 years. During this period, original spare parts will be available to operate the appliance properly.
This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices and other working environments;
- farm houses; by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- areas for communal use in blocks of flats or in launderettes.
Children’s safety
Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.
Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product.
Do not forget to close the loading door when leaving the room where the product is located.
Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.

While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the washing operation is in progress.

Package information

Packaging materials of the product are manufactured from recyclable materials in ac- cordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

Disposing of the waste product

This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resources by recycling used products. For children’s safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product.

Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its service life. Take it to the collection center for the recycling of electrical and electronic equipment. Please consult your local authorities to learn about these collection centers.

Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

C| Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer’s responsibility.
---|---
Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.
| Warning: Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.
| Warning: Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.
Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!
Do not place the product on the power cable.
Do not install the product at places where temperature may fall below 0ºC.
Place the product at least 1 cm away from the edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

Removing the transportation locks

| Warning: Do not remove the transportation locks before taking out the packaging reinforcement.
---|---
WARNiNG : Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

Loosen all the bolts with a suitable spanner until they rotate freely (C).
Remove transportation safety bolts by turning them gently.
Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

| Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.
---|---
Never move the product without the transportation safety bolts properly fixed in place!

Connecting water supply

The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.
warning: Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.
warning: Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry

. Tighten all hose nuts by hand. Never use a tool when tightening the nuts.
Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

Connecting to the drain

The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

warning: Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.

The hose should be attached to a height of at least 40 cm, and 100 cm at most.
In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure.
To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.
The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.
If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

Adjusting the feet

warning: In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from it.

Loosen the lock nuts on the feet by hand.
Adjust the feet until the product stands level and balanced.
Tighten all lock nuts again by hand.

warning: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged

Preparation

Sorting the laundry

Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature.
Always obey the instructions given on the garment tags.

Preparing laundry for washing

Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case.
Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.
Put small size clothes such as infant’s socks and nylon stockings in a laundry bag or pillow case.
Place curtains in without compressing them. Remove curtain attachment items.
Fasten zippers,sew loose buttons and mend rips and tears.
Wash “machine washable” or “hand washable” labeled products only with an appropriate programme.
Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately.
Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the instructions on the package.
Wash trousers and delicate laundry turned inside out.
Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling.
Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage.

Things to be done for energy saving
Following information will help you use the product in an ecological and energy-efficient manner.

Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, “Programme and consumption table”.
Always follow the instructions on the detergent packaging.
Wash slightly soiled laundry at low temperatures.
Use faster programmes for small quantities of lightly soiled laundry.
Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
If you plan to dry your laundry in a dryer,select the highest spin speed recommended during washing process.
Do not use detergent in excess of the amount recommended on the detergent package.

Initial use
Before starting to use the product, make sure that all preparations are made in accordance with the instructions in sections“ Important safety instructions” and “Installation”. To prepare the product for washing laundry, perform first operation in Drum Cleaning programmed. If your product is not equipped with Drum Cleaning programmed, perform the Initial Use procedure in accordance with the methods described under “5.2 Cleaning the loading door and the drum”section of the user manual.

Use an anti-limescale suitable for the washing machines. Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product.

Correct load capacity
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. The machine automatically adjusts the amount of water according to the weight of the loaded laundry.

warning: Follow the information in the “Programme and consumption table”.When overloaded, machine’s washing performance will drop. Moreover, noise and vibration problems may occur.

Loading the laundry

Open the loading door.
Place laundry items loosely into the machine.
Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.

The loading door is locked while a programme is running. The door can only be opened a while after the programme comes to an end.

warning : In case of misplacing the laundry, noise and vibration problems may occur in the machine.

Using detergent and softener

When using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer’s instructions on the package carefully and follow the suggested dosage values. Use measuring cup if available.

Detergent Drawer
The detergent drawer is composed of three compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener compartment

Detergent, softener and other cleaning agents

Add detergent and softener before starting the washing programme.
Never leave the detergent drawer open while the washing programme is running!
When using a programme without prewash, do not put any detergent into the prewash compartment (compartment nr. “1”).
In a programme with prewash, do not put liquid detergent into the prewash compartment (compartment nr. “1”).
Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the machine.
If you are using liquid detergent, do not forget to place the liquid detergent cup into the main wash compartment (compartment nr. “2”).

Choosing the detergent type
The type of detergent to be used depends on the type and colour of the fabric.

Use different detergents for coloured and white laundry.
Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.) used solely for delicate clothes.
When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
Wash woolens with special detergent made specifically for woolens.

WARNING: Use only detergents manufactured specifically for washing machines.
WARNING: Do not use soap powder.

Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.
Use lesser detergent for small amounts or lightly soiled clothes.

Using softeners
Pour the softener into the softener compartment of the detergent drawer.

Do not exceed the (>max<) level marking in the softener compartment.
If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.

Using liquid detergents If the product contains a liquid detergent cup:

Make sure that you have placed the liquid detergent cup in compartment nr. “2”.
If the liquid detergent has lost its fluidity, dilute it with water before putting in the detergent cup.

If the product is equipped with a liquid detergent part:

When you want to use liquid detergent, pull the apparatus towards yourself. The part that falls down will serve as a barrier for the liquid detergent. If required, clean the apparatus with water when it is in place or by removing it. If you will use powder detergent, the apparatus must be secured at top position.

If the product does not contain a liquid detergent cup:

Do not use liquid detergent for the prewash in a programme with prewash.
Liquid detergent stains your clothes when used with Delayed Start function. If you are going to use the Delayed Start function, do not use liquid detergent.

Using gel and tablet detergent
Apply the following instructions when using tablet, gel and similar detergents.

If the gel detergent thickness is fluidal and your machine does not contain a special liquid detergent cup, put the gel detergent into the main wash detergent compartment during first water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before starting the programme.
If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly into the drum before washing.
Put tablet detergents into the main wash compartment (compartment nr. “2”) or directly into the drum before washing.

Tablet detergents may leave residues in the detergent compartment. If you encounter such a case, place the tablet detergent between the laundry, close to the lower part of the drum in future washings.
Use the tablet or gel detergent without selecting the prewash function.

Using starch

Add liquid starch, powder starch or the fabric dye into the softener compartment.
Do not use softener and starch together in a washing cycle.
Wipe the inside of the machine with a damp and clean cloth after using starch.

Using bleaches

Select a programme with prewash and add the bleaching agent at the beginning of the prewash. Do not put detergent in the prewash compartment. As an alternative application, select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step.
Do not use bleaching agent and detergent by mixing them.
Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes skin irritation. Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes.
When using oxygen based bleaches, select a programme that washes at a lower temperature.
Oxygen based bleaches can be used together with detergents; however, if its thickness is not the same with the detergent, put the detergent first into the compartment nr. “2” in the detergent drawer and wait until the detergent flows while the machine is taking in water. Add the bleaching agent fromthe same compartment while the machine is still taking in water.

Using limescale remover

When required, use limescale removers manufactured specifically for washing machines only.

Tips for efficient washing

| Clothes
---|---

(Recommended temperature range based on soiling level: 40-90 °C)
Soiling Level| (difficult stains such as grass, coffee, fruits and blood.)| It may be necessary to pre-treat the stains or perform prewash. Powder and liquid detergents recommended for whites can be used at dosages recommended for heavily soiled clothes. It is recommended to use powder detergents to clean clay and soil stains and the stains that are sensitive to bleaches.
Normally(For example, stains caused by body on collars and cuffs)| Powder and liquid detergents recommended for whites can be used at dosages recommended for normally soiled clothes.
**** (No visible stains exist.)| Powder and liquid detergents recommended for whites can be used at dosages recommended for lightly soiled clothes.

Detergent Recommendation

Recommended washing detergent| Wash cycles| Washing temp.| Type of laundry and textile
---|---|---|---
Heavy-duty| Cotton、| |
detergent with| Mix、| |
bleaching agents and optical brighteners| Bedding、 Stain、 20℃、ECO40-60| 30/40/60| White laundry made fromboil-proof cotton or linen
Colour| Cotton、 Mix、Underwear、 Bedding、 20℃、Quick 15’、Steam| |
detergent| |
without bleaching| | Coloured laundry
agent and optical brighteners| 20/30/40| madefrom cotton or linen
Color or mild| Mix、Down wear、Steam、 Quick 15’、 Underwear| | Coloured laundry
detergent withoutoptical| Cold/20/ 30/40| madefrom easy care fibres or
brighteners| | synthetic materials
Mild washing detergent| Silk、Down wear、 Underwear| Cold/20/30| Delicate textiles, silk, viscose
Special wool detergent| woolen| 20/30/40| **** Wool

Agglomerating or ropy detergent or additive can be diluted in some water detergent dispenser, to avoid its inlet to get blocked before pouring it into the and thus cause a water overflow.
Please choose the suitable type of detergent to get a maximum of washing performance and a minimum of water and energy consumption
To achieve the best cleaning result a proper detergent dosing is important.
Use a reduced detergent amount if the drum is not filled completely.
Always adjust the amount of detergent to the water hardness, if your tap water is soft, use less detergent.
Dose according to how dirty your laundry is, less dirty clothes require less detergent.
Highly concentrated (compact detergent) requires particularly accurate dosing.

Following symptoms are a sign of detergent overdosing:

heavy foam formation
poor washing and rinsing result

Following symptoms are a sign of detergent underdosing:

laundry turns grey
built-up of limescale deposits on the drum, the heating element and/or the laundry

Operating the product

Control panel

Programme Selection knob (Uppermost position On / Off)
Display
Smart button
Programme Follow-up indicator
Start / Pause button
Auxiliary Function buttons
Spin Speed Adjustment button
Temperature Adjustment button

Preparing the machine

Make sure that the hoses are connected tightly. Plug in your machine. Turn the tap on completely. Place the laundry in the machine. Add detergent and fabric softener.

P rogramme selection

Select the programme suitable for the type, quantity and soiling degree of the laundry in accordance with the “Programme and consumption table” and the temperature table below.
90°C| Heavily soiled white cottons and linens. (coffee table covers, tableclothes, towels, bed sheets, etc.)
---|---
60°C| Normally soiled, coloured, fade proof linens, cottons or synthetic clothes (shirt, nightgown, pajamas, etc.) and lightly soiled white linens (underwear, etc.)
40°C- 30°C- 20°C- Cold| Blended laundry including delicate textile (veil curtains, etc.), synthetics and woolens.
Select the desired programme with the Programme Selection button.
| appropriate for that particular type of fabric.
---|---
When selecting a programme, always consider the type of fabric, colour, degree of soiling and permissible water temperature.
Always select the lowest required temperature. Higher temperature means higher power consumption.

Program introduction
Depending on the type of fabric, use the following main programmes. • Cotton Use this programme for your cotton laundry (such as bed sheets, duvet and pillowcase sets, towels, bathrobes, underwear, etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle.
Down
Wear The process of down wear is specially designed for washing down jacket. The material of down jacket is light, difficult to rinse, poor anti washing ability, and difficult to absorb water. Therefore, it is necessary to extend the soaking time in the washing process, and reduce the rotation speed during dehydration.
Woolen
Use this programme to wash your woolen clothes. Select the appropriate temperature complying with the tags of your clothes. Use appropriate detergents for woolens.
Bedding
The main washing objects of the propiam ae bed sheets, quilt cover, curtains, overcoats and tablecloths and so on. In the mosheng process, the muzking time and washing time of the knd are verersed is improve the washing effect.
Drum Clean
Periodically (every 1-2 month use this program to clean the drum for necessary sanitation deaning Let the am thing machine sun the programme without any laundry. For better results, add powdend limescale cleannig ant to the detergent box. After the program, inve the hont door aur and let the inside of the machine try
Stain
For the clothes with more suitors stains the washing effect can be amproved by longer washing time and strong wasting thytten
Underwear
Linderuar program is it special program for washing underwear and other close fitting clothers. The washing him is weak. At the same time, in onter to ensure the naty performance and prevent detergent restitue, the mang
Sitk
You can choose this programmed to wash delicate fabrics such silk. The wash is very genthe, and the spin step is not done right away. This programmed is best if the laundry requires a
Stram
Steam washing process is to proze shaam in the washang process, improve the wasting effect and at the same time steam in the clothes to present wrinkles
Quick 15
Quick wash 15 na hatt washing program for a small amount of man dirty clities. Its planai washing tempmature range in now and the womum speed of dehydration is lo
Mix
Use this programme to wash your cuttion and synthette clothes together without sorting the
20 C
New European stanttani special program veed to wish some mid clothes, the temperature can only be selected at 210 C, to protect the cinthes
ECO 40-60
For washing cotton garments that pre nonmally stable 40°C or 60°C, ale wasting at the same cycle. The cycle is used to assess compliance with Election nepabons.

Programme and consumption table

EN| Auxiliaryfunctions|
---|---|---
**** Programme| Max.load(kg)| Rinse+| Wash+| Delay| **** Selectable temperature range °C
Mix| 30| 5| •| •| •| Cold-60
Quick 15′| 0| 1.5| •| •| •| Cold-30
Silk| 0| 2.5| •| •| •| Cold-40
Bedding| 30| 5| •| •| •| Cold-60
Underear| 40| 3| •| •| •| Cold-90
Rinse Spin| –| Max.| •| | •| –
Spin| –| Max.| | | •| –
ECO 40-60| 40| Max.| | | •| 40
Stain| 60| 5| •| •| •| 40-60
Cotton| 40| Max.| •| •| •| Cold-90
Down Wear| 30| 3| •| •| •| Cold-40
Woolen| 30| 2.5| •| •| •| Cold-40
Steam| 90| 5| •| •| •| 90
20℃| 20| Max.| •| •| •| 20
Drum Clean| 90| 0| | | | 90
Smart| AUTO| Max.| •| | | AUTO

Auxiliary function selection
Select the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme without pressing the Start / Pause button when the machine is operating. For this, the machine must be in a step before the auxiliary function you are going to select or cancel.If the auxiliary function cannot be selected or canceled, light of the relevant auxiliary function will blink 3 times to warn the user. C Additional laundry may be loaded during the delayed start period.
Wash+
In the standby mode, press the enhanced washing function setting button,the Strengthen washing function indicator will be on, and the Strengthen washing function will be added in the washing process. After selecting the Strengthen washing function, the washing time in the main washing stage will be increased by 10 minutes, and the time after adding the Strengthen washing function will be displayed in the remaining time window. If you press it again, the Strengthen washing function will be cancelled.
Rinse+
Press the rinse Plus button in standby mode, and the rinse plus function indicator will be on. At the same time, add a rinse process in the washing process, and the time after adding the function will be displayed in the remaining time window. The rinse function will cancelled when it is pressed again, if it does not run to the rinse stage during operation, press the pause button, The rinsing button can be added or cancelled, and the rinsing function cannot be selected or cancelled during operation.
Smart Start
The smart start program is an intelligent program, whichcan be entered and run automatically in the standby and power off states. Under the smart start program, the washing temperature, water level and washing time are automatically set according to the weighing results, and the washing parameters do not need to be set by the user.
Delay
With the Delayed Start function the startup of the programme may be delayed up to hours. Delayed start time can be increased by increments of 1 hour. To activate the Child Lock: Press and hold 3st and 4nd Auxiliary Function buttons for 3 s Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes.Open the loading door, place the laundry and put detergent, etc. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions. Set the desired time by pressing the Delay button. Press Start / Pause button. The delayed start time you have set is displayed. Delayed start countdown starts. The‘:’ in the display time blinks once every second, and the time gradually decreases.

Additional laundry may be loaded during the delayed start period.

At the end of the countdown, duration of the selected programmed will be displayed. ‘:’symbol will disappear and the selected programmed will start.

Canceling the Delayed Start function
If you want to cancel the delayed start countdown and start the programmed immediately: Set the Delayed Start period to zero or turn the Programme Selection knob to any programme. Thus, Delayed Start function will be canceled. The End/Cancel light flashes continuously. Then, select the programme you want to run again. Press Start / Pause button to start the programmer.

Starting the programmed
Press Start / Pause button to start the programme. Programme follow-up light showing the startup of the programmed will turn on.

Child Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid any changes in a running programmed.

If the Programmed Selection knob is turned when the Child Lock is active, “ ” appears on the display. The Child Lock does not allow any change in the programmes and the selected temperature, speed and auxiliary functions.
Even if another programme is selected with the Programmed Selection knob while the Child Lock is active, preeviously selected programme will continue running.

To activate the Child Lock:
Press and hold 3st and 4nd Auxiliary Function buttons for 3 seconds while any programme is running. The Child Lock is activated. If you press any button or turn the Programme Selection knob when the Child Lock is active, “CL” will appear on the display and blink 3 times.

To deactivate the Child Lock:
e rP ssand hold 3st and 4nd auxiliary function buttons for3 seconds while any programme is running. The Child Lock is deactivated.

In addition to the above way, to remove the child lock, there are two ways:

The program is automatically removed after running.
The alarm will be automatically lifted.

Child Lock is not deactivated after power failures or when the machine is unplugged.

Progress of programme

Progress of a running programme can be followed from the Programme Follow-up indicator. At the beginning of every programme step, the relevant indicator light will turn on and the indicator light that completes the step will be on. You can change the auxiliary functions, speed and temperature settings. You need to stop the program flow before changing the auxiliary functions, speed, and emperature settings while the programme is running. To do this, the change you are going to make must be in a step after the running programme step.

If the change is not compatible,press the relevant key sound prompt tone. i If the machine does not pass to the spinning step, Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine

Loading door lock
There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable. Loading door light will start flashing when the machine is switched to Pause mode. Machine checks the level of the water inside. If the level is suitable, Loading Door light illuminates steadily within 1-2 minutes and the loading door can be opened.

If the level is unsuitable, Loading Door light turns off and the loading door cannot be opened. If you are obliged to open the Loading Door while the Loading Door light is off, you have to cancel the current programme; see “Canceling the programme”.

Changing the selections after
programme has started Switching the machine to pause mode
Press the Start / Pause button to switch the machine to pause mode while a programme is running. The light of the step which the machine is in starts flashing in the Programme Follow-up indicator to show that the machine has been switched to the pause mode. Also, when the loading door is ready to be opened, procedure step light is steady on, door lock light is off.

Changing the speed and temperature settings for
auxiliary functions
Depending on the step the programme has reached, you may cancel or activate the auxiliary functions; see, “Auxiliary function selection”. You may also change the speed and temperature settings; see, “Spin speed selection” and “Temperature selection”.

C If no change is allowed, the indicator light will be on.

Adding or taking out laundry
Press the Start / Pause button to switch the machine to pause mode. The programme follow-up light of the relevant step during which the machine was switched into the pause mode will flash. Wait until the Loading Door can be opened. Open the Loading Door and add or take out the laundry. Close the Loading Door. Make changes in auxiliary functions, temperature and speed settings if necessary. Press Start / Pause button to start the machine.

Canceling the programme
To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be canceled. End / Cancel light will flash continuously to notify that the programme has been canceled. Pump function is activated for 1-2 minutes regardless of the programme step, and whether there is water in the machine or not. After this period, your machine will be ready to start with the first step of the new programme.

Depending on the step where the programme was canceled in, you may have to put detergent and softener again for the programme you have selected anew.

End of programme
“End” appears on the display at the end of the programme. Wait until the loading door light illuminates steadily. Press On / Off button to switch off the machine. Take out your laundry and close the loading door. Your machine is ready for the next washing cycle.

Maintenance and cleaning

Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time.

If more than normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.

Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.
If more than normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.
Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning.
Insert the drawer back into its place after cleaning and make sure that it is seated well.
If your detergent drawer is the one indicated in the following figure:

Use an anti-limescale suitable for the washing machines.

After every washing make sure that no foreign substance is left in the drum

If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick.

Foreign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool or wire wool.
warning: Never use sponge or scrub materials. These will damage the painted and plastic surfaces.

Cleaning the body and control panel
Wipe the body of the machine with soapy water or noncorrosive mild gel detergents as necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.

Cleaning the water intake filters
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters should be cleaned as they do get dirty
Close the taps.

Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.
Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.
Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.

Draining remaining water and cleaning the pump filter
The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained off first to clean the pump filter.
In addition, prior to transporting the machine (e.g., when moving to another house) and in case of freezing of the water, water may have to be drained completely.

WARNING : Foreign substances left in the pump filter may damage your machine or may cause noise problem

In order to clean the dirty filter and discharge the water: 1. Unplug the machine to cut off the supply power.
WARNING : Temperature of the water inside the machine may rise up to 90 ºC. To avoid burning risk, filter must be cleaned after the water in the machine cools down.

Some of our products have emergency draining hose and some does not have. Follow the steps below to discharge the water.

Discharging the water when the product does not have an emergency draining hose

a Place a large container in front of the filter to catch water from the filter.
b. Loosen pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any spilled water.
c. When the water inside the machine is finished, take out the filter completely by turning it.
Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.
Install the filter.
If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat the tabs in the lower part into their places first, and then press the upper part to close.

Regular cleaning
Clean the interior of the pump hosing, removing any debris or foreign objects.periodic cleaning, including optimal frequency, and limescale prevention and procedure. If the appliance water supply slows or stops completely, the water inlet strainer may be blocked. Cleaning is recommended every 6 months in any event to reduce chances of valve blockage in areas using hard water.

Programmes

S351210KW

Cycle| Nominal capacity in kg| Temperature Setting| Cycle duration in hours and minutes| Energy consumption in kWh/operalling cycle| Highest temperature ature ℃| Residual motisure in%/spin speed
Quick 15| 1.5| Cold| 0:15| 0.046| Cold| 80.5%/800
20℃| MAX.| 20| 0:50| 0.162| 20| 76.5%/800
Cotton40℃| MAX.| 40| 0:58| 0.804| 40| 76.5%800
Mix| 5.0| 30| 0:52| 0.552| 30| 76.5%800
Bedding| 5.0| 30| 1:15| 0.648| 30| 76.5%800
Woolen| 2.5| 30| 1:00| 0.536| 30| 90.5%/400
**** ECO40-60| 2.5| –| 3:00| 0.270| 25| 62.9%/1200
5.0| –| 3:00| 0.625| 35| 62.9%/1200
MAX.| –| 3:59| 1.050| 39| 62.9%/1200

The above data is for reference only, and the data may change due to different actual use conditions.
The valves given for programmes other than the ECO 40-60 programme are indicative only

Troubleshooting

Program does not start after closing the door.

Start / Pause / Cancel button was not pressed. >>> *Press the Start / Pause / Cancel button.

Programme cannot be started or selected.

Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> To cancel the programme, turn the Programme Selection knob to select another programme. Previous programme will be cancelled. (See “Canceling the programme”)

Water in the machine.

Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the machine.

Machine vibrates or makes noise.

Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
A hard substance might have entered into the pump filter. >>> Clean the pump filter.
Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine.
Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.

Machine stopped shortly after the programme started.

Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level.

Programme time does not countdown. (On models with display)

Timer may stop during water intake. >>> Timer indicator will not countdown until the machine takes in adequate amount of water. The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water. Timer indicator will resume countdown after this.
Timer may stop during heating step. >>> Timer indicator will not countdown until the machine reaches the selected temperature.
Timer may stop during spinning step. >>> Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum.
Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.

Foam is overflowing from the detergent drawer.

Too much detergent is used. >>> Mix 1 tablespoonful softener and ½ l water and pour into the main wash compartment of the detergent drawer.
Put detergent into the machine suitable for the programmes and maximum loads indicated in the “Programme and consumption table”.
When you use additional chemicals (stain removers, bleachs and etc), reduce the amount of detergent.

Laundry remains wet at the end of the programme

Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage.

Use recommended amount of detergent.
Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and to its surrounding environment. Laundry should be rearranged and re-spun.