TANUR B0CK3F475M 12 inch Portable Outdoor Propane Oven Instruction Manual
- June 17, 2024
- TANUR
Table of Contents
- TANUR B0CK3F475M 12-inch Portable Outdoor Propane Oven
- GAS CYLINDER WARNING
- Before lighting
- Parts List
- Converting to Fixed Fuel Systems (Large Propane Tank)
- Instructions
- Operating instructions
- Leak testing
- Care and maintenance
- Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TANUR B0CK3F475M 12-inch Portable Outdoor Propane Oven
WARNING
To reduce the risk of fire, burn hazard or other injury, read this safety
manual carefully and completely before using this
WARNING
Before cleaning, make sure the gas supply and control knob is in the OFF
position and the burner and oven have cooled.
DANGER
- Never operate this appliance unattended.
- If a fire should occur, keep away from the appliance and immediately call your fire department. Do not attempt to extinguish an oil or a grease fire with water.
- Failure to follow these instructions could result in fire, explosion or burn hazards which could cause property damage, personal injury or death.
DANGER
If you smell gas
- Shut off the gas to the appliance
- Extinguish any open flame
- If the odour continues, keep away from the appliance and immediately call your gas supplier or your fire department.
- Failure to follow these instructions could result in fire, explosion or burn hazard which could cause property damage, personal injury or death.
WARNING
FOR OUTDOOR USE ONLY
WARNING
the included matchstick holder.
WARNING
- Keep the fuel supply hose away from any heated surface(s).
- The use of alcohol, prescription or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate the appliance.
- Keep children and pets away from the appearance at a. ames.
- Do not move the appliance when in use.
- This appliance is not intended for and should never be used.
WARNING
Spiders and insects can nest inside the burner of the appliance clogged tubes
can lead to a fire beneath the appliance.
WARNING
Gas cylinders must be stored outdoors, out of the reach of children, and
should not be stored in a building, garage, or any other enclosed area.
WARNING
Do not store gas cylinders in a building, garage or any other enclosed area
and keep out of reach of children at all times
WARNING
Check all gas supply fittings for leaks before each use. Do not use the
appliance until all connections have been checked and do note
WARNING
Do not smoke while leak testing. Never leak test with an open
WARNING
When lighting, keep your face and hands as far away from the
WARNING
Minimum clearance from sides of the unit to combustible Minimum clearance from
the back of the unit to the combustible construction is 915mm (36 inches).
WARNING
This manual includes an instruction to clean and inspect the hose before each
use of the appliance. If there is evidence of abrasion, wear, cuts, or leaks,
the hose must be replaced prior to the appliance being put into operation. The
replacement hose assembly shall be specified by the manufacturer.
WARNING
This manual states that on the oven, wyer or broiler shot not cel used on or
under any apartment or condominium balcony or deck.
WARNING
This instruction manual contains important information necessary for the
proper assembly and safe use of the appliance. Read and follow all warnings
and instructions before assembling and using the appliance. Follow all
warnings and instructions when using the appliance. Keep this manual for
future reference.
WARNING
This appliance is not intended to be installed in or on a boat. This appliance
o not intended to be installed in or on al
WARNING
Do not modity the appliance
CAUTION
The burner tube openings must be positioned properly over the valve
orifice,
WARNING
This appliance shall be used only outdoors, and shall not be used in a
duelling garage, or any other enclosed area.
WARNING
The appliance is not intended for commercial use.
WARNING
This manual includes a list of required parts necessary for the safe operation
of the appliance, directions for proper and for assembly of installed parts
and accessories supplied with the appliance, and proper procedures for gas
leak testing.
WARNING
The appliance should not be located or used under overhead unprotected
combustible construction materials or surfaces. For a grill, fryer or broiler,
the minimum clearance shall be at least 10ft (3m) from any structure or
combustible material.
WARNING
Turn off the gas supply at the gas cylinder after use.
WARNING
This appliance must be kept away from flammable materials during use.
GAS CYLINDER WARNING
- Do not store spare liquid propane gas cylinders under or near this appliance
- Never fill the cylinder beyond 80 per cent capacity,
- Liquid propane cylinder must be fitted with an OVERFILL PROTECTION DEVICE (OPD)
- The cylinder supply system must be arranged for vapour Windrawal
- If the information above is not followed exactly, a fire resulting in death or serious injury may occur. local codes or, in the absence of local codes, with the
- National Fuel Gas Code, ANSI 2223.1/NFPA 54, Storage anxious
- Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or
- Natural Gas and Propane Installation Code, CSA B149.1;
- Propane Storage and Handing, CSA B149.2
- The cylinder to be used must be constructed and marked according to the specifications for LP gas cylinders, U.S. Department of Transportation (DOT) or the Standards for Cylinders.
- Spheres and Tubes for the Transportation of Dangerous Goods, CAN/CSA-B339.
WARNING
The appliance will be hot during and after use. Use insulated oven mitts or
gloves for protection from hot surfaces. Connecting the gas hose to your TANüR
Always route the gas hose away from the oven. The hose must not touch the oven
body.
WARNING Hose pipe can be a tripping hazard
Before lighting
Inspect the gas supply hose before turning on the gas. If there is evidence of cut, wear or abrasion, it must be replaced before use. Screw the regulator onto the gas cylinder. Leak check the hose and regulator connections with a soap and water the solution before lighting the appliance. Only the pressure regulator and gas hose assembly supplied with this appliance should be used. If replacement pressure regulators and hose assemblies are required, they should be those specified by the appliance manufacturer, Ooni Limited.
Safety practices to avoid injury
- When properly cared for, your oven will provide safe, reliable service for many years. However, extreme care must be taken as the oven produces intense heat that can increase the risk of accidents.
- When using this oven basic practices must be followed, including but not limited to the following:
- Do not repair or replace any part of the oven unless specifically recommended in this manual. All other services should be referred to a qualified technician.
- Children should not be left alone or unattended in an area where the oven is being used. Do not allow children to sit, stand or play around the oven at any time.
- Never let clothing or other flammables come in contact with or too close to any burner or hot surface until it has cooled. The fabric could ignite, causing serious personal injury.
- For personal safety, wear proper apparel. Loose fittings garments or sleeves should never be worn while using the oven. Some synthetic fabrics are highly flammable and should not be worn while cooking.
- Do not heat unopened food containers as a build-up of pressure may cause the containers to burst. When lighting the burner, always pay close attention to what you are doing.
- When using the oven, do not touch the outer shell, stone baking board or immediate surroundings as these areas become extremely hot and could cause burns.
- Do not use the oven to cook extremely fatty meats or other products that increase flare-up.
- Keep the area surrounding the oven free from combustible material including fluids, trash and vapours such as gasoline or charcoal lighter fluid.
- Do not obstruct the flow of combustion and ventilation air.
- Never use the oven in extremely windy conditions.
- The temperature under the oven is high. Do not place the oven on a table with flammable tablecloths, plastic or any other inflammable materials.
Parts List
- TANÜR oven
- Stone baking board.
Assembly
Before assembly, make sure all parts are present. If any part is missing or
damaged, do not attempt to assemble the appliance. Contact customer service
for replacement parts.
Step 1
Unfold the legs
Step 2
Insert the stone baking board
Step 3
Connect to a gas canister.Regulators will vary depending on the region.
WARNING
- Please always keep the gas bottle in an upright position.
- The size of 20 lbs LP gas cylinder is 12.2 inches in diameter and 17.9 inches tall
- If the appliance is not in use, the gas must be turned off at the supply cylinder.
- The cylinder used must include a collar to protect the cylinder valve
- The minimum distance for the appliance and the 20lb gas tank is 25 inches apart.
QCCi gas regulator
This gas fitting is clockwise. Make sure that the tank is completely switched
off and screw the regulator as far as possible into the gas tank valve
Connecting the liquid propane as a cylinder
- The cylinder valve should be in the OFF position.
- Make sure the burner valve is in the OFF position.
- Inspect the valve connections, port and regulator assembly. Remove debris and inspect the hose for damage.
- When connecting the regulator assembly to the valve, use your hand to tighten the nut clockwise until it stops.
- The use of a wrench could damage the quick coupling nut and result in a hazardous situation.
- Open the cylinder valve fully by turning the valve counter-clockwise.
- Before lighting the oven, use a soap and water solution to check all connections for leaks.
- If a leak is found, turn the cylinder valve OFF, and do not use the oven until a local liquid propane dealer can make repairs.
Disconnecting the liquid propane gas cylinder
- Turn the oven burner valve OFF and make sure the oven is cool.
- Turn the liquid propane cylinder valve OFF by turning clockwise until it stops.
- Detach the regulator assembly from the cylinder valve by turning the quick coupling nut counterclockwise.
- Place a dust cap for the cylinder valve outlet whenever the cylinder is not in use.
- Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane.
Converting to Fixed Fuel Systems (Large Propane Tank)
WARNING
FIRE, EXPLOSION, AND CARBON-MONOXIDE HAZARD If the information in these
instructions is not followed exactly, a fire, explosion, or production of
carbon monoxide may result causing property damage, personal injury, or loss
of life. This conversion kit shall be installed by a qualified agency by the
appliance, manufacturer instructions and all applicable codes and requirements
of the Authority Having Jurisdiction. The qualified agency is responsible for
the proper installation of this kit. The Installation is not proper and
complete until the operation of the converted appliance is checked as
specified in the manufacturer’s instructions supplied with the kit.
NOT INCLUDED
DH22 model hose and quick connectors to Fixed Fuel System
- The appliance and its shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures over 1/2 psi (3.5kPa).
- The appliance must be isolated from the gas supply piping system by closing its manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5kPa).
Instructions
- Caution: Before proceeding with the conversion; shut off the gas supply and ensure the oven is cool to the touch. Remove the baking stone and turn the oven upside down.
- Remove the gas hose using a 19mm wrench.
- Attach the DH22 gas hose using a 19mm wrench.
- Attach quick connectors at the end of the gas hose and connect to the fixed fuel system.
- Perform a leak test to ensure the connection is safe and proper. (p. 10)
Operating instructions
Using the oven
Each burner is rated at 13,300 BTU/Hr.
To begin:
- Make sure the oven has been leak-tested and properly placed.
- Remove any remaining packing material.
- Light the burner using the lighting instructions below Lighting instruction
To light the burner
Read all instructions before lighting
- Make sure the control knob is in the OFF position, and then turn the liquid propane cylinder valve ON by slowly cutting counter clockwise.
- Push in and slowly turn the control knob anticlockwise until you hear a click and the burner ignites.
- Continue to push in the control knob for 5 seconds after ignition and then release.
- If the burner doesn’t light within 5 seconds, turn the knob OFF, wait 5 minutes and repeat the lighting.
To light with a match
- If the burner will not light after several attempts using the control knob, the burner may be lit with a match.
- If you have already attempted to light the burner using the control knob, wait 5 minutes for any gas to dissipate.
- Insert a match into the matchstick holder, ignite the match and insert it through the oven opening to the burner.
- Push and turn the control knob to HI slowly, the burner should ignite immediately.
- Continue to push in the control knob for 5 seconds after ignition and then release.
- If the burner does not light within seconds, turn the control knob OfF and wait 5 minutes and try again.
Leak testing
General
Although the gas connections of the appliance are leak-tested before packing
and shipment, a complete test must be performed at the installation site.
Before each use, check all the gas connections for leak testing using the
procedure listed below. If the smell of gas is detected at any time, you
should immediately stop using it and check the entire system for leaks.
Before testing
Make sure all packing material has been removed from the appliance. Make a
solution of one part liquid detergent and one part water. You will need a
spray bottle, brush or rag to apply the solution to the fittings.
To test
- Turn the burner valve OFF.
- Turn the liquid propane cylinder valve on counter-clockwise to open the valve.
- Apply the soap solution to all gas fittings. Soap bubbles would appear where a leak is present.
- If a leak is present, immediately turn the gas supply OFF and tighten leaky fittings.
- Turn the gas back ON and recheck.
- Should the gas continue to leak from any of the fittings, turn the gas supply OFF and contact customer service.
Care and maintenance
Store TANüR oven out of direct sunlight and indoors where possible and when storing for extended periods of time. TANüR oven should not be exposed to harsh weather conditions such as snow, heavy rain and strong winds.
Wait for the TANüR oven to cool completely before moving
The outer shell of the TANüR oven may fade over time and through use. This
will not affect performance.
Stone baking board
- DO NOT use the stone over an open flame
- Avoid extreme temperature changes to the stone. DO NOT place frozen foods on a hot stone
- The stone is fragile and can break if bumped or dropped
- The stone is very hot during use and stays hot for a long time after use.
- DO NOT cool the stone with water when the stone is hot
- After cleaning the stone with water, please dry the stone before use. This can be done in a conventional oven at 60°C (140°F) for 2 hours.
- Burnt on food can be cleaned by flipping the stone where it will clean itself due to the high oven temperatures Oven Interior Wipe down with a paper towel between uses to remove any debris.
Other areas of the oven
Clean when required using a non-abrasive sponge
Troubleshooting
Product technical information
Model number
TANüR
Product Label
Menutesturer same bore tre
Moos ANON
ANS Z2189-2017 CSA 118-2017 Oundoor Cocking Specialty Gas Appliances
LIGHTING INSTRUCTION – TO LIGHT THE BURNER
Make sure the control Knob in the OFF position, ON by slowly turning the
counterclockwise valve Push in and slowly turn the control knob anticlockwise
until you hear a click and the burner ignites. It burner doesn’t light within
5 seconds, turn the knob OFF, wait 5 minutes and repeat the lighting, Flame
King Inc, 6616 Sauton Ave. Ico Rivera CA 90660
Manufacturer Address:
Flame King inc., 8616 Slauson Ave., Pico Rivera, CA, 90660
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>