havit HV1207MR16T Adjustable LED Wall Pillar Light Instruction Manual

Tivah Single Adjustable
Installation Instructions

Product Specifications

Model No.| HV1207MR16T| HV1217MR16T| HV1227MR16T| HV1237MR16T| HV1247MR16T| HV1277MR16T| HV1287MR16T|  HV1297MR16T
---|---|---|---|---|---|---|---|---
Name| Torah
Material| 316 Stainless Steel| Solid Copper| Aluminum| Aluminum| Aluminum| Solid Brass| Aluminum| Solid Brass
Colour| Stainless Steel| Copper| Black| White| Silver| Graphite| Titanium| Antique Brass
IP Rating| IP65
Input Voltage| 12v DC (Requires external power supply)
Lamp Base| MR16
Lamp Wattage| 1 x 5w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 270lm, 2851m, 300lm
CRI| > 80
Dimmable| No (not with globes supplied)
Warranty| 3 Years Replacement*

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MRI6 = 20w
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
• When installing copper fittings, gloves must be worn to avoid any oils transferring to the fitting.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
• All o-rings and seals must be in place correctly to maintain the warranty.
• These instructions may be updated at any time due to product improvements. Please visit the website for the most current installation instructions.

Steps for Installation:

1. Make sure that the electrical circuit is free of voltage (master switch off)
2. Loosen alien screws on side of the base and separate the mounting bracket from the fitting.
3. Install the backing plate securely using appropriate screws for application, Seal all holes in the backing plate including cable entry and screw holes. Failure to do so will void the warranty
4. Connect the cable – Connect live and neutral wire to a suitable 12v DC LED Driver – when connecting more than 1 fitting, Wiring must be done in Parallel (DO NOT CONNECT DIRECTLY TO 240V POWER)
5. Affix the fitting to the mounting bracket and tighten Allen screws, making sure these are tight to avoid any water penetration.
6. Apply a silicon seal around the whole base plate to avoid any water getting into electrical connections.
7. Colour temperature and wattage are preset to 3000k, to change remove the cover from the fitting by twisting anti-clockwise and setting it aside. Remove the globe and select desired color temperature by moving the switches on side of the globe and reinserting the globe into the lamp holders.
8. Adjust the fitting to desired position making sure to stop rotating when the fitting cannot rotate anymore, If forced fitting w continues to rotate and cause internal cables to become entangled causing the fitting to short. If this is done, the warranty will be voided.
9. Reattach covers by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.
10. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Changing Globe:

1. Remove the cover by twisting anti-clockwise and set aside, remove the globe by holding on the outer rim of the globe and gently pulling.
2. Re-insert the appropriate globe by inserting the 2 pins into the lamp holder and gently push down. (Make sure not to exceed max wattage, see product label for correct info)
3. Reattach the cover by turning clockwise making sure the seals are still in place and caps are tight to avoid any water penetration.

Must be installed by a licensed electrician

Contact Details:|
---|---
143 Beauchamp Road
Matraville NSW 2036
Australia| Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
Warranty Terms & Conditions*| Additional Information
---|---
|
https://havit.com.au/pages/warranty-terms-and-conditions| https://havit.com.au/

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>