ELEKICO 65141932 52 Inch Ceiling Fan Light User Manual
- June 17, 2024
- ELEKICO
Table of Contents
ELEKICO 65141932 52 Inch Ceiling Fan Light
Safety Information
READ AND SAVE THESE INSTRUCTIONS.
- To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
- All wiring must be by the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
- The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL-listed outlet boxes marked ” Acceptable for Fan Support of 35 lbs. (15.9 kg) or less. “
- Do not place objects in the path of the blades.
- To clean the fixture, turn off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth.
- After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment- grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
- All set screws must be checked and retightened where necessary before installation.
- WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuitry.
- WARNING: To reduce the risk of fire or injury do not use this product in conjunction with any variable (rheostat) wall control.
- WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert balancing the blades, or cleaning the fan. Do not insert
- WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marke “acceptable for fan support of 35 lbs. (15.9 Kg) or less’ and use screws provided with the outlet box.
- WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring
- WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control/switch.
- CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.
- CAUTION: Please use it carefully when working around or cleaning the fan to avoid injury or damage of fan.
- CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.
- CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Dimension Reference
PART LIST
Hardware Included
Fan Parts Included
Exploded View
Installation Instructions
Step1 MOUNTING
- Take out fan downrod.
- Remove cotter pin and bolt from downrod.
- Take out fan motor housng.
- Loosen jam screw in yoke until it is flush with the inside surface.
- Place the downrod inside the canopy, canopy cover, and yoke cover.
- Route wires exiting motor through yoke cover, canopy and downrod.
- Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires.
- Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
- Secure downrod in position by tightening jam screws.
- Slide yoke cover down and it will flush with the motor housing.
CAUTION: To ensure wobble-free operation and to avoid damage to the fan,
the downrod and the set crew must be completely
tightened.
Step2 INSTALL MOUNTING BRACKET
WARNING: To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury,
Mount To UL/CSA Listed Outlet Box Marked Acceptable for Fan Support And Use
Mounting Screws Provided With The Outlet Box
- Secure hanger to metal outlet box.
- The ceiling fan is hung on the hanger, with the hanger ball groove aligned with the hanger boss.
Step3 Attaching the Fan Blades.
- Attach the blade to the motor with blade screws.
- Repeat this step for each blade assembly.
Step4 Assembling the lamp housing
- Feed the wire through the center hole of the lamp housing
- Fix the lamp housing with screws.
- Connect the plugs from the motor and LED.
Step5 The lampshade installation
- Install the lampshade to the lamp housing by turning clockwise to lock it into place.
Step6 The receiver installation
- Put the receiver in the hanger.
Step7 Wiring the Fan
- Wiring according to the wiring diagram.
NOTE: Once ground wires are connected, carefully tuck all wires and marrettes into the metal box making sure that the wires are clear of the hemisphere and downrod when positioned in hemisphere and downrod when positioned in mounting bracket.
Step8 Attaching the Canopy and Canopy cover
- Slide the canopy up to the ceiling and attach it to the hanger with the screws provided. Tighten all screws securely.
- Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism)
FUNCTION INSTRUCTION OF EMITTER
- Open battery cover on the hand-held remote and install a battery, pair of AAA of emitter(1.5V) that are not included.
- If the emitter can not control the fan, learning code matching mode is used between emitter and receiver.
- Turn on the power switch, press the”SETUP”key within 3 seconds, the receiver issues a “tick”two sounds, the pair code is successful. If not successful, turn off the power for a minute an repeat the above.
- When the emitter cannot control the receiver, please check the battery switch touching normally or not, correct the positive and negative, full or empty of the power.
- When the emitter cannot control the receiver, please check is there any existence of similar remote-controlled products nearby, then check whether they works, because remote-controlled product with the same frequency will disturb each other.
- Please take out the battery from the emitter when leaving unused for long time.
- When installing the fan, the fan ceiling cover don’t press the antenna(or other wire), it is easy to break down the wire and is short-circuited.
- Main switch off fan and light
- Fan forward rotating
- Natural wind
- Speed controller
- Mach code/Turn off fan
- Timer
- Light switch on/off
- Fan reversal rotating
Troubleshooting Guide
If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly, installation,or wiring. In some cases, these installation errors may be mistaken for defects.If you experience any faults please check this troubleshooting guide.
Balancing Kit
The Balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your owner’s Manual under “Attaching The Fan Blades.”
- Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
- Turn off the fan and allow it to come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of blade.
- Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
- Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
- Remove the clip and install a balancing weight to the top of blade along the center line near the point where the clip was positioned.
- If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and additional weights.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>