BOSCH 45 EasyHedgeCut Hedge Trimmer Instruction Manual

: June 4, 2024
: Bosch

Table of Contents

BOSCH 45 EasyHedgeCut Hedge Trimmer
Safety Notes
General Power Tool Safety Warnings
Product Description and Specifications
- Technical Data
Operation
Troubleshooting
Maintenance and Service
- Maintenance, Cleaning and Storage
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BOSCH 45 EasyHedgeCut Hedge Trimmer

Safety Notes

Explanation of symbols

Read instruction manual.
Do not expose to rain.
Switch off and remove mains plug from socket outlet before adjusting, cleaning, maintenance or if the cable is entangled or if the cable is cut or damaged and before leaving the product unattended or any period.
Keep hands away from blade.

General Power Tool Safety Warnings

WARNING
Read all safety warnings, instructions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cord-less) power tool.
Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded sur-faces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carry-ing, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suit-able for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is un-avoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal in-juries.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal in-jury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
If devices are provided for the connection of dust ex-traction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe in-jury within a fraction of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de-signed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or re-move the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be per-formed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Hedge trimmer safety warnings

Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal in-jury.
Carry the hedge trimmer by the handle with the blade stopped and taking care not to operate any power switch. Proper carrying of the hedge trimmer will de-crease the risk of inadvertent starting and resultant personal injury from the blades.
When transporting or storing the hedge trimmer, al-ways fit the blade cover. Proper handling of the hedge trimmer will decrease the risk of personal injury from the blades.
When clearing jammed material or servicing the unit, make sure all power switches are off and the power cord is disconnected. Unexpected actuation of the hedge trimmer while clearing jammed material or servicing may result in serious personal injury.
Hold the hedge trimmer by insulated gripping sur-faces only, because the blade may contact hidden wiring or its own cord. Blades contacting a “live” wire may make exposed metal parts of the hedge trimmer “live” and could give the operator an electric shock.
Keep all power cords and cables away from cutting area. Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade.
Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning. This decreases the risk of being struck by lightning.

Additional safety warnings

This tool is not intended for use by persons (including children) with reduced physical, sensory or mental cap-abilities, or lack of experience and knowledge, unless they have been given supervision or instruction concern-ing use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more secure with both hands.
Always ensure all handles and guards are fitted when using the machine. Never attempt to use an incomplete machine or one fitted with an unauthorized modification.
Always lubricate the cutting blade with protective spray before use.
Always wait until the machine has come to a complete stop before placing it down.
Other persons and animals should remain at a distance of 3 meters or more when the machine is being used. The operator is responsible for third persons in the working area.
Never grasp the blade of the hedge trimmer.
Children or persons unfamiliar with these instructions must not operate the hedge trimmer. Local regulations may restrict the age of the operator.
Never cut a hedge while people, especially children or pets, are nearby.
The user is responsible for accidents or hazards occurring to other people or their property.
Do not operate the hedge timer when barefoot or wear-ing open sandals, always wear substantial footwear and long trousers. The use of sturdy gloves, non-skid footwear and safety glasses is recommended. Do not wear loose clothing or jewellery which can be caught in moving parts.
Thoroughly inspect the area where the hedge trimmer is to be used and remove all wires and other foreign objects.
Prior to operation, check cutter blades, blade bolts and cutter assembly for wear or damage. Do not operate with a damaged or excessively worn cutting device.
Know how to stop the hedge trimmer quickly in an emergency.
Cut a hedge only in daylight or in good artificial light.
Never operate the hedge trimmer with defective guards or without the guard in place.
Always ensure all handles and guards supplied are fitted when using the hedge trimmer. Never attempt to use an incomplete hedge trimmer or one with an unauthorized modification.
Never hold the hedge trimmer by the guard.
When operating the hedge trimmer, ensure to keep proper footing and balance at all times.
Always be aware of your surroundings and stay alert for possible hazards that you may not hear whilst operating the hedge trimmer.
Keep all nuts, bolts and screws tight to ensure that the hedge trimmer is always in a safe working condition.
The hedge trimmer should be stored in a dry, high or locked up place out of the reach of children.
Replace worn or damaged parts for safety.
Do not attempt to repair the machine unless you are qualified to do so.
Ensure replacement parts fitted are Bosch-approved.
To safeguard against contact with the moving cutter blade, this hedge trimmer is constructed with two handles each with a blade control (switch). To operate the hedge trimmer, both controls must be actuated simultaneously. Do not use the tool, if it runs without a switch being actuated or just one switch being actuated.

Electrical Safety

Warning: Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled.
Your machine is double insulated for safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V 50 Hz) Contact your Bosch Service Centre for details. If in doubt contact a qualified electrician or the nearest Bosch Service Centre.
For increased electrical safety use a Residual Current Device (RCD) with a tripping current of not more than 30 mA. Al-ways check your RCD every time you use it.
Keep the supply cables away from moving hazardous parts and avoid damage to the cables; this can lead to contact with live parts.
The connections (plugs and sockets) should be kept dry and off the ground.
The supply cables must be inspected for signs of damage at regular intervals and may only be used if in perfect condition.
If the supply cable on the product is damaged, it must only be replaced by a Bosch Service Centre. Only use approved extension cables.
Use only extension cords, cables, leads, cable reels that comply with EN 61242/IEC 61242 or IEC 60884-2-7.
If you want to use an extension cable when operating your product, only the following cable dimensions should be used:

```
* Nominal conductor area of 1.25 mm2 or 1.5 mm2
```
- Maximum length 30 m for a Cord Extension Set or maximum length of 60 m for a Cable Reel with Residual Cur-rent Device (RCD).

Note: If an extension cable is used it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations.
WARNING! Inadequate extension cables can be dangerous. Extension cable, plug and socket must be of watertight construction and intended for outdoor use.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorized customer service agent. The replacement plug should have the same fuse rating as the original plug.
he severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere

Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Symbols
The following symbols are important for reading and under-standing the original instructions. Please take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the product in a better and safer manner.

Symbol Meaning

Wear protective gloves
Wear safety glasses/goggles
Movement direction
Reaction direction
Weight
Switching On
Switching Off
CLICK! Audible noise
Prohibited action
Accessories/Spare Parts

Product Description and Specifications

Read all safety warnings and all instructions. Failure to follow the safety warnings and instructions may result in electric shock, fire and/or serious injury.
Please observe the illustrations at the ending of this operating manual.

Intended Use
The machine is intended for cutting and trimming hedges and bushes in domestic use.

Product features (see figures A and B)
The numbering of the product features refers to the illustration of the product on the graphics pages.

Handle (insulated gripping surface)
On/Off switch
Lock-off button for On/Off switch
Hand guard
Blade
Protection sleeve
Mains plugA)
Extension cable

A) country specific

Technical Data

Article number| | 3 600 H47 A..| 3 600 H47 A06| 3 600 H47 B..| 3 600 H47 C..
---|---|---|---|---|---
Rated power input| W| 420| 420| 450| 450
No-load stroke speed| min–1| 3400| 3400| 3400| 1700/3400
Cutting length| mm| 450| 450| 500| 550
Tooth opening| mm| 16| 16| 16| 16
Weight according to EPTA‑Procedure 01:2014| kg| 2.6| 2.6| 2.7| 2.8
Protection class| | / II| / II| / II| / II
Serial number| | see type plate on garden tool

Noise/Vibration Information
That the declared vibration total value(s) and the declared noise emission value(s) have been measured in accordance with a standard test method any may be used for comparing one tool to another.
That the declared vibration total value(s) and the declared noise emission value(s) may also be used in a preliminary assessment of exposure.
That the vibration and noise emissions during actual use of the power tool can differ from the declared values depend-ing on the ways in which the tool is used especially what kind of workpiece is processed; and of the need to identify safety measures to protect the operator that are based on an estimation of the exposure measures in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
Noise emission values determined according to EN 62841-4-2:2019 .
Typically the A-weighted noise levels of the product are: Sound pressure level 75 dB(A); sound power level 95 dB(A). Uncertainty K = 2.0 dB.
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 62841-4-2:2019:
ah = 2.5 m/s2, K = 1.5 m/s2.

Operation

Pay attention to the mains voltage. The voltage of the power source must match the voltage specified on the rating plate of the machine.

Switching ON/OFF (see figures C and D)
To switch ON, firstly press and hold the lock-off button for On/Off switch (3). Then press the On/Off switch (2) and keep it pressed.
To switch OFF, release the lock-off button for On/Off switch (3) and then release the On/Off switch (2).

Working with the Hedge cutter (see figure E)
Move the hedge cutter evenly forward along the cutting line. The double edge cutting blade enables cutting in either direction, or with a side to side motion.
Cut the sides of the hedge first, then the top.
To cut the sides straightly, we recommend cutting from bot-tom to top in the direction of growth. Younger stems tend to move outwards when cutting them from top to bottom, resulting in shallow patches or holes in the hedge.
To reach a level finish, fasten a piece of string along the length of the hedge at the required height and use as an alignment guide. Cut the hedge just above the string.
Pay attention that no objects such as wires are cut. The blade or drive can be damaged.

Troubleshooting

Hedgecutter does not operate	Power turned off	Turn power on
Mains socket faulty	Use another socket
Mains cable damaged	Check mains cable; if damaged, contact Service Agent
Extension cable damaged	Inspect extension cable, replace if damaged
Fuse faulty / blown	Replace fuse
Hedgecutter operates intermittently	Internal wiring of garden tool defective

Maintenance and Service

Maintenance, Cleaning and Storage

Before any work on the product, disconnect supply cord from the mains.
For safe and proper working, always keep the product clean.
Do not place other objects on the garden product.
To ensure safe and efficient operation, always keep the product and the ventilation slots clean.
Never spray the product with water.
Never immerse the product in water.
Store the product in a secure, dry place, out of the reach of children.
Do not place other objects on the product.
Keep all nuts, bolts and screws tight to ensure safe working with the product.
Inspect the product and replace worn or damaged parts for safety.
Ensure replacement parts fitted are Bosch-approved.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at: www.bosch- pt.com/serviceaddresses

Disposal
The product, accessories and packaging should be sorted for environmental- friendly recycling. Do not dispose of products into household waste!

Only for EU countries
According to the European Directive 2012/19/EU on Waste Electrical and Electronic Equipment and its implementation into national law, power tools that are no longer usable must be collected separately and disposed of in an environment-ally friendly manner.