GRUNDIG GLCD2206HDV Misuro HD LCD TV With DVD Player User Manual

: June 17, 2024
: GRUNDIG

Table of Contents

GRUNDIG GLCD2206HDV Misuro HD LCD TV With DVD Player
Product Information
Product Usage Instructions
Unpacking
Installation Guidelines
View of the TV/Monitor

GRUNDIG GLCD2206HDV Misuro HD LCD TV With DVD Player

Product Information

Specifications

Model: GLCD1906HDV Series, GLCD2206HDV Series
Power Supply: AC 100-240 Volts, 50/60 Hz
Screen Size: 19″ (GLCD1906HDV Series), 22″ (GLCD2206HDV Series)
Display Type: LCD
DVD Player: Built-in
Adaptor Type: NU60-2120500-I1

Product Usage Instructions

Safety Instructions

Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched, particularly at the plug, convenience receptacles, and the point where they exit from the apparatus.

Installation Notes
This TV can be connected to AC 100-240 Volts, 50/60 Hz. Never connect to a DC supply or any other power supply. Locate the TV in a room where light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and
indirect lighting is recommended for comfortable viewing. Allow enough space between the TV and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure. Do not cover the ventilation openings when using the TV.

Additional Safety Notes

Never tamper with any components inside the TV or any other adjustment controls not mentioned in this manual.
All LCD TVs are high voltage instruments. When you clean up dust or water drops on the LCD PANEL or CABINET, the power cord should be pulled out from the receptacle, then wipe the TV with a dry soft cloth.
During thunder and lightning, unplug the power cord and antenna cord to prevent damage to your TV.
All repairs to this TV should only be performed by qualified TV service personnel.

Unpacking

Please make sure that the following items are included with your LCD TV/Monitor. If any item is missing, please contact the warranty line.

TFT LCD TV/Monitor
Remote control
DC adaptor
RCA cable
Operation manual
Power cord
Car Cord
Wall Mount Bracket

Installation Guidelines

Place the LCD TV on a solid surface. Use soft material to place over the front screen to avoid any damage.
Remove the 5 screws from the unit and take away the stand.
Using the plastic cover that came with the LCD, screw in the 5 screws to fix the plastic cover on the bottom of the unit.
Use 4 screws to fix the TV on the wall mount bracket. Please find there are 4 VESA holes on the back of the unit.

View of the TV/Monitor

FAQ

Q: Can I use this TV with a DC power supply?
A: No, this TV is designed to be connected to an AC power supply only. Using a DC power supply or any other power supply may damage the unit.

Q: How should I clean the TV?
A: Clean the TV with a dry soft cloth. Make sure to pull out the power cord from the receptacle before cleaning. Do not use any liquid cleaners on the LCD panel or cabinet.

Q: Can I perform repairs on the TV myself?
A: No, all repairs to this TV should only be performed by qualified TV service personnel.

MISURO HD LCD TV WITH DVD PLAYER
GLCD1906HDV Series GLCD2206HDV Series
The Gold Technical Support Line: 1902 215 259 Personal Product Support
(Charges will apply at $2.95 per minute)

Introduction
Thank you for buying this Grundig product, which is designed to give you many years of trouble-free service. You may already be familiar with using a similar unit, but please take time to read these instructions. They are designed to familiarize you with the unit’s many features and to ensure you get the very best from your purchase. Safety is important Your safety and the safety of others is important. Therefore, please ensure you read the “Safety Instructions” before you operate this unit. Warranty In the unlikely event that your product fails to work normally, please call the below free phone number to discuss the problem with one of our qualified service engineers. Australia. Grundig Warranty: 1800 509 394 New Zealand Grundig Warranty: 0800 450 259

Safety instructions
1. Do not use this apparatus near water. 2. Clean only with a dry cloth. 3. Do not block any ventilation openings. Install in accordance with the
manufacturers instructions. 4. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat. 5. Protect the power cord from being walked on or pinched particularly at
plugs convenience receptacles, and the point where they exit from the apparatus. 6. Only use attachments/accessories specified by the manufacturer. 7. Unplug this apparatus during lightning storms or when unused for long periods of time. 8. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 9. The apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on the apparatus. 10. If the television is to be built into a compartment or similar enclosed space, the minimum distances must be maintained. Heat build-up can reduce the service life of your television, and can also be dangerous.

Installation notes This TV can be connected to AC 100-240 Volts. 50/60 Hz. Never connect
to a DC supply or any other power supply. Locate the TV in the room where light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain.
Soft and indirect lighting is recommended for comfortable viewing. Allow enough space between the TV and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the
cabinet or premature component failure. Do not cover the ventilation openings when using the TV. Additional Safety notes Never tamper with any components inside the TV, or any other
adjustment controls not mentioned in this manual. All LCD TVs are high voltage instruments. When you clean up dust or
water drops on the LCD PANEL or CABINET, the power cord should be pulled out from the receptacle, then wipe the TV with a dry so ft cloth. During thunder and lighting, unplug the power cord and antenna cord to prevent damage to your TV. All repairs to this TV should only be performed by quali fied TV service personnel.

Unpacking

Please make sure that the following items are included with your LCD
TV/Monitor. If any item is missing, please contact the warranty line.

TFT LCD TV/ Monitor

Remote control DC adaptor RCA cable

Operation manual Power cord Car Cord

Wall Mount Bracket Installation Guidelines
5

1. Place the “LCD TV” on a solid surface. Use soft material to place over the front screen to avoid any damage.
2. Remove the 5 screws () from the unit and take away the stand (Refer picture 1).

(Picture 1) 3. Using the plastic cover that came with the LCD screw in the 5 screws to
fix the plastic cover on the bottom of the unit (Refer picture 2).

(Picture 2) 4. Use 4 screws to fix the TV on the wall mount bracket .Please find there
are 4 VESA holes on the back of the unit (Refer picture 3).

I. View of the TV/Monitor
Front view 6

(Picture 3)

Back view
3 4 5 6 7 8 9 10 11

GLCD 2206HDV W ,,
22 Widescreen LCD TV With DVD Player
DC 12V 5A Adaptor
Use only the adaptor type NU60-2120500-I1 Other adaptor may damage the unit

MADE IN PRC

N14119
Grundig Warranty: 1800 509 394 Australia Grundig Warranty: 0800 450 259 New Zealand

CLA SS 1 LA SER PRO DUCT LUO KA N 1 LA SERLA ITE
KLA SS 1 LA SERA PPA RA T
2008/05

12

13 14 15 16 17 18 1920 21 22 23 24

1. Remote sensor To receive remote signal from remote control.

12. DVD disc slot To load disc for playback.
13. DC IN jack

7

2. Power button / power indicator

To connect DC 12V power supply

To switch on/off the unit, in power 14. HDMI input jack

on mode the indicator will turn to

15. VGA input jack

blue and in standby mode the

To connect with PC.

indicator will turn to red.

16. YPbPr input jack

3. PLAY/PAUSE button

17. S-Video input jack

To play/pause playback of disc.

18. Video input jack

4. STOP button

19. Audio input (Left) jack

To stop playback of disc.

20. Audio input (Right) jack

5. EJECT/CLOSE button

21. PC audio input jack

To eject a disc from the disc slot or 22. Earphone jack

close a disc to the disc slot.

23. RF IN jack

6. VOL- button

To connect the external aerial.

To decrease the volume level.

24. COAXIAL OUT

7. VOL+ button

To connect the input socket on your

To increase the volume level.

surround sound system, this jack

8. CH- button

only output the SPDIF/PCM

To select channels downward in

TV mode.

9. CH+ button

To select channels upward in TV

mode.

10. MENU button

To enter menu mode.

11. SOURCE button

To select input source.

8

II. Remote Control
9

(1) Remote control keys function

1. STANDBY: To switch on/off the unit.

21. REPEAT: To repeat play in DVD mode

2. Numeric buttons: To select a channel by

and display yellow subject in Teletext

number input or input numbers in menus.

mode.

3. CH.LIST: To show the channel list and used 22. A-B: To repeat A-B playback or display

to input the track number for discs that have

blue subject in Teletext mode.

more than 9 tracks.

23. D.DISP: To display track information in

4. ASPECT: To switch the size of the picture.

DVD mode.

5. VOL+/-: To adjust the volume up or down. 24. GOTO: To find a play point in DVD

6. DISPLAY: To display the source and

mode.

channel’s information.

25. REVEAL: To reveal or hide the words in

7. Navigation buttons: To select the items of

Teletext mode and select angle in DVD

on-screen menus.

mode (Angle function depends on DVD

8. LCD MENU: To display LCD OSD Menu

discs).

9. SOURCE: To display INPUT source.

26. SUBPAGE: To access sub-coded page

10. P.MODE: To select the picture mode.

in Teletext mode and zoom function of

11. PLAY/PAUSE: To play/pause the track

DVD playback.

being played in DVD mode or show the 27. LANG: To select a program’s language

favourite list in TV mode.

in DVB mode and DVD mode (where

12. STOP: To stop DVD playback.

available).

13. TEXT: To switch on/off Teletext in TV

28. SUBTITLE: To switch the dialogue at

mode and skip to previous track in DVD

the bottom of the screen.

mode.

29. >I: Slow motion playback in DVD mode.

14. HOLD: Hold on or off for current page

30. EPG: To show the electronic program

display in TELETEXT mode and skip to

Guide menu

next track in DVD mode.

31. S.MODE: To select different sound

15. INDEX: To display the index page in

mode.

Teletext mode and fast backward playing 32. SLEEP: To set the unit to turn off

in DVD mode.

automatically after a set period of time.

16. SIZE: To change the display size in

33. EXIT: To display the setup menu in DVD

Teletext mode or fast forward playing in

mode or exit the current mode.

DVD mode.

34. CH+/-: To change channels up or down.

17. D.MENU: To display DVD-disc menu.

35. NICAM: To turn on/off Nicam in TV

18. TITLE: To display DVD title menu.

mode.

19. PROG: To enter program setting in DVD 36. CYCLE: Switch between the current

mode, display red subject in Teletext

channel being viewed and the last

mode and select DVB program in DVB

channel viewed in TV mode.

mode.

37. EJECT: To eject/close the disc in DVD

20. INTRO: To INTRO play (play the first 10

mode.

seconds of each track) when playing CD 38. MUTE: To turn the sound on and off.

discs and display green subject in Teletext

mode.
10

(2) Remote control battery installation and cautions
Replace battery by following the below steps: Requires two AAA batteries. 1. Open the battery cover as shown below:
2. Install the battery into the battery tray.
3. Close the battery cover
Caution: 1. Keep batteries out of children’s reach. 2. Don’t attempt to recharge, short-circuit, disassemble heat or throw the
batteries into the fire. 3. Always replace both batteries at the same time. Never mix new and old
batteries or batteries of a different type. 4. If you don’t intend to use the remote control for an extended period,
remove the batteries to prevent possible leakage and corrosion. Notes: 1. Do not drop, apply shock or step on the remote control. 2. Do not spill water on the remote control. 3. Do not use the remote control for other equipment at the same time. 4. If the TV does not operate when operating the remote control from a
close range, you need to replace the batteries. See above for directions on replacing batteries.
11

III. Installation and Connection
Connect the LCD TV/monitor

GLCD2206HDV ,,
22 Widescreen LCD TV With DVD Player DC 12V 5A Adaptor
Use only the adaptor type NU60-2120500-I1 Other adaptor may damage the unit

MADE IN PRC

N14119
Grundig Warranty: 1800 509 394 Australia Grundig Warranty: 0800 450 259 New Zealand

CLA SS 1 LA SER PRO D UCT LUO KA N 1 LA SERLA ITE
KLA SS 1 LA SERA PPA RA T
2008/03

1. Connect the TV RF source to the RF IN port. TVRF signal including: Receiving antenna /satellite TV/CATV net. You can use 75 coaxial cable to connect the outdoor antenna.
Outdoor Antenna Connection:
Use 75 coaxial cable plug or 300-75 impedance converter to plug in antenna input terminal on the rear of the cabinet.

VHF antenna

UHF antenna

GLCD2206HDV ,,
22 Widescreen LCD TV With DVD Player
DC 12V 5A Adaptor
Use only the adaptor type NU60-2120500-I1 Other adaptor may damage the unit

MADE IN PRC

N14119
Grundig Warranty: 1800 509 394 Australia Grundig Warranty: 0800 450 259 New Zealand

CLA SS 1 LA SER PRO D UCT LUO KA N 1 LA SERLA ITE
KLA SS 1 LA SERA PPA RA T
2008/03

Mixer

75Co-axis cable Input terminal of antenna

Antenna in jack
12

Co-axis antenna plug
75Co-axis cable

2. Connect the audio sources (Including DVD, VCDR, etc.) to the proper AUDIO input jacks L’ andR’.
3. Connect the video source to the VIDEO input jack by RCA cable. 4. Connect the video source to the S-VIDEO input jack of the TV by the
S-video cable 5. Insert the AC power to the DC adaptor, then connect 12V input jack from
the monitor to its DC output jack. 6. When using the LCD as a computer screen, connect the PC from the
VGA jack of the monitor by the relevant cable.
IV. TV/Monitor Screen Operation
(1) Basic operation
1. Press the STANDBY button on the unit or from the remote control to switch on the power. The power indicator will light up in blue colour. Press the STANDBY button again to switch off the power, and the indicator will change to red.
2. Press the VOL – or VOL + button to adjust the volume level. Press the VOL – button repeatedly to decrease the volume; press the VOL + button repeatedly to increase the volume from 0 to 100.
(2) Changing Channels
1. Press the SOURCE button on the remote control to select the ATV or DTV input mode. If you are using the receiver for the first time, an Installation Guide menu will be displayed to guide you through the channel scan, Use the remote control to finish channel scan (you can also refer to Chapter V in this manual for the channel scan operation).
13

2. Channel `1′ will appear on the left top corner of the screen after the

channel scanning is finished. Press the CH- or CH+ button to select the

previous or next channels or press the 0-9 buttons to enter a channel

number directly.

3. Press the

button on the remote control to switch between the

present channel to the last channel was viewed.

4. Press the P.MODE button repeatedly to cycle through the available

video picture modes from the below different types

Standard

Mild

User

Dynamic

5. Press the S.MODE button repeatedly to cycle through the available sound modes from the below different types

Music

Movie

Sports

User

Standard
6. Press the MUTE button to cut off the sound output, press this button again to resume sound output.
7. Press the DISPLAY button to display the preset channel information.

(3) View different input signal sources
Press the SOURCE button then press the or button to select the available input sources as follow:

DTV

ATV

AV

S-Video

HDMI

VGA

DVD

YPBPR

(4) View the TELETEXT program
1. Press the SOURCE button to select the DTV mode. Then press the CHor CH+ button on the remote control to select a DTV channel in order to pick up the TELETEXT signal, if broadcast.
14

2. Press the TEXT button to enter TELETEXT mode, press the TEXT button again to exit.
3. Press the CH- or CH+ button to select the previous page or press the 0-9 numeric buttons for the next page. Note: The first number should not be 0′ or 9′.
4. Refer to the chapter of `Remote Control’ to understand other functions of the TELETEXT buttons.
V. TV Channel Menu and Adjustment CHANNEL menu
– Press SOURCE button to select DTV or ATV input. – Press LCD MENU button and the CHANNEL menu will appear.
– Press to select the items: Auto Tuning, DTV Manual Tuning, and ATV Manual Tuning, Program Edit. Press ENTER button to confirm. – Press the LCD MENU button to return to previous menu. – Press the EXIT button to exit the menu.
Auto tuning
15

DTV Manual tuning
– Press to select the channel, then press ENTER to start scan.
ATV manual tuning
16

– Press the or button to select the items, and press the or button to Adjust. See details in the following sub-options. – Press the ENTER button to confirm and press the LCD MENU button to Return to previous menu or press the EXIT button to exit.
Storage To
Press the or button to select the channel number you want to save to.
System
Press the or button to select the TV sound system.
Current CH
Press the or button to select the current channel.
Search
Press the or button to search backward/forward, Press the LCD MENU or EXIT to stop the program searching.
Fine-Tune
Press the or button to fine tuning when the signal level of the current channel is weak.
Skip
Press the or button to turn on/off the switch of skip. When it’s set to ON, the current channel will be skipped when you switch channels by pressing the CH+ or CH- buttons.
Program Edit
17

– Press the or button to select the channel.

Delete

Press red button, DELETE mark will be shown on the current channel; Press

red button again, the current program will be deleted.

Rename

Press green button, RENAME mark will be shown on the current channel;

then move cursor by or button, select characters by or button, at

last press LCD MENU button to confirm this operation and return to previous

menu.

Swap

Press or button firstly to move cursor to selected current program

channel 1. And press yellow button to confirm, SWAP mark will be shown

on the current channel

Then press or button firstly to move cursor to target program channel

2. SWAP mark will be shown also .And press yellow button to confirm.

Skip

Press blue button, SKIP mark will be shown on the current channel, it means

the current program will be skipped and could not be searched; Press blue

button again, the mark SKIP will disappear, it means you cancel skip program

selection.

FAV

Press FAV button, a mark will display on the current item, it means you

have selected favorite program; Press FAV button again, the mark

will

disappear, it means you cancel current favorite program selection.

PICTURE menu

18

– Press the LCD MENU button to display the OSD menuthen press the or button to select PICTURE menu.
– Press the or button to select the items in PICTURE menu, press the button to enter the sub-menu, press the LCD MENU button to return to the previous menu or press the EXIT button to exit.
Picture Mode
Press the or button to select picture modes.
Contrast
Press the or button to adjust the contrast.
Brightness
Press the or button to adjust the brightness.
Colour
Press the or button to adjust the colour.
Sharpness
Press the or button to adjust the sharpness.
Tint
Press the or button to adjust the sharpness, this option only works in VGA mode and VGA input connected.
Colour Temperature
Press the or button to select colour temperature: Cool User, Warm, and Standard.
Red
Press the or button to adjust
Green
Press the or button to adjust
Blue
Press the or button to adjust
Aspect Ratio
Press the or button to select Aspect Ratio: Zoom1, Zoom2, Auto, 4:3, 16:9.
Noise Reduction
19

Press the or button to turn the Noise Reduction function on or off.
SOUND menu
– Press the LCD MENU button to display the OSD menuthen press the or button to select SOUND menu.
– Press the or button to select the items in SOUND menu, press the or button to enter the sub-menu, press the LCD MENU button to return to the previous menu or press the EXIT button to exit.
Sound Mode
Press the or to select sound mode: User, Standard, Music, Movie, Sports.
Treble
Press the or button to adjust the treble.
Bass
Press the or button to adjust the bass.
Balance
Press the or button to adjust the balance of left/right output channels.
Auto Volume
Press the or button to select off or on, when it’s set to on, the volume level will be reduced automatically if you set the volume too high.
Surround Sound
Press the or button to turn the surround sound effect on or off.
20

TIME menu
– Press the LCD MENU button to display the OSD menu, then press the or button to select TIME menu.
– Press the or button to select the items in TIME menu, press the or button to enter the sub-menu, press the LCD MENU button to return to the previous menu or press the EXIT button to exit.
Clock
Press the or button to select hour and minute, press the or button to set the current time.
Off time
Press the or button to select on, press the button to enter the setup sub- menu, then to set the time you want the unit to be turned off, select the time using the ,, or buttons.
On time
Press the or button to select on, press the button to enter the setup sub- menu, then to set the time you want the unit to be turned on, select the time using the ,, or buttons.
Sleep timer
Press the or button to set the sleep time: 240min, 180min, 120min, 90min, 60min, 30min, 20min, and 10min.

Auto sleep
Press the or button to select on or off. When it’s set to on, the unit will turn to standby mode automatically if there is no signal input for a period of about 5 minutes.
Time Zone
Press the or button to set the time zone.
OPTION menu
– Press the LCD MENU button to display the OSD menuthen press the or button to select OPTION menu.
– Press the or button to select the items in OPTION menu, press the or button to enter the sub-menu, press the LCD MENU button to return to the previous menu or press the EXIT button to exit.
Language
Press the or button to select the OSD language, the default language is English.
Audio Language
Press the or button to select the Audio language, the default language is English.
Subtitle Language
Press the or button to select the Subtitle language, the default language is English.
Country 22

To show the country you have set when you started auto scan.
Restore Setting
Press the button to restore; this operation will reset the unit to factory default.
LOCK menu
– Press the LCD MENU button to display the OSD menuthen press the or button to select LOCK menu.
– Press the button and enter password, the default password is “0000”. – Press the or button to select the items in LOCK menu, press the or
button to enter the sub-menu, press the LCD MENU button to return to the previous menu or press the EXIT button to exit.
Lock Channel
Press the or button to turn off or on.
Change Password
Press the ENTER or button and enter the new password.
Block Program
Press the ENTER or button to enter the program list. Press the or button to select the channel you want to lock then press the green button to lock, the lock icon will appear behind the locked channel, to un-lock the channel, select the locked channel and press the green button again, the lock

icon will disappear.
Parental Guidance
Press the or button to set program rating to block some of programs.
Hotel Mode
Press the ENTER or button to enter the hotel mode list. Press the or button to select the related item, and set by or button
EPG menu
The EPG (Electronic Programme Guide) menu is used to look at what is being broadcast on a DTV or Radio channel at a later point in time. Press the EPG button to access the EPG menu, the detailed program information of the channel currently being viewed will be displayed.

To see what is going to be broadcast after the current programme, press the button to change the time and press the button to move the time back. To view a different channel, press the or button. To book a wanted program for later watching, press the blue button to enter setting menu. Press the green button to enter the schedule list. To exit the EPG menu and watch the selected channel, press the EPG or EXIT button.

VI. DVD PLAYER OPERATION

a. Basic operation

1. Press the SOURCE button on the remote control to select the DVD

function mode. Insert a disc into the slot of the DVD player and it will start

to read the disc automatically.

2. Press the eject.

button on the remote control, the disc will automatically

Note: Insert the disc with reflective data side facing to the front of

the TV. Some slight picture and sound noise are produced when

the disc is loading, unloading and during playback. This is normal

and can be ignored.

HOW TO SELECT THE TRACK If you want to play the second track or chapter, press the number button “2” directly. Then press the ENTER button to play.

HOW TO PAUSE PLAYBACK (STILL PLAYBACK) 25

Press the PLAY/PAUSE button once during playback. Press the PLAY/PAUSE button again to resume normal playback.
HOW TO REMOVE THE DISC Press the button on the remote control. Wait until the disc is completely ejected before removing.

HOW TO STOP PLAYBACK Press the STOP button once, the DVD video player will stop. Then press the PLAY button to resume playback of the disc from the same point. Press the STOP button twice, and disc will stop completely. Press the PLAY button to start the DVD playback from the first track.

FAST FORWARD/ BACKWARD

Press the or buttons to toggle between different playback speeds in

sequence at x2, x4, x8 or x20. Press the

button to return playing at

normal speed.

Note: The sound is not available while playing in this mode.

SKIP TO NEXT/ PREVIOUS TRACK
Press the or buttons to select the next track or previous track.

b. Slow Play

Press the SLOW/STEP (>I) button when playing, the disc will play at 1/2, 1/3,

1/4, 1/5, 1/6, 1/7 of the normal speed. Press the

button to return playing

at normal speed.

Note: The sound is not available while playing in this mode.

c. Zoom Picture
This DVD video player allows you to zoom in/out of a picture as well as shift the zoom point. Press the ZOOM button during normal play or when in slow motion. The DVD player magnifies the center of the picture at 2x, 3x, 4x, 1/2, 1/3, 1/4 of the normal picture.

d. Repeat Play 26

You can use the REPEAT button to repeat the play of various sections of your DVD. Press the REPEAT button once to repeat playing the present chapter. Press the REPEAT button again to repeat playing the present title. Press the REPEAT button third time to repeat playing the whole disc. Press the REPEAT button for the fourth time to cancel repeat play and return to normal play. Note: For different discs, the REPEAT button may have a different function.
REPEAT A to B SPECIFIC SECTION You can repeat a specific section by the A-B button on the remote control. Firstly press the A-B button at the beginning of the section you want, and then press it again at the end of the section. The unit will now repeat playing from A to B. If you want to cancel the repeat section, please press the A-B button once again. Note: Some discs will not respond to the A-B repeat function.
e. Mute
Press the MUTE button on the remote control to suppress the sound output while a disc is playing. Press the same button again to resume playing with sound.
f. Menu playback
Press the D.MENU button to display disc menu or return to the root menu when playing the DVD discs. Note: For different DVD discs, the D.MENU button may have different menu display information.
g. Title playback
Press the TITLE button when playing the DVD discs, there will be an indication ” TITLE ” on the screen. Press the , , or buttons to select your favorite title and press the

ENTER button to play from the first chapter of selected title.

h. INFO
During playback, press the D.DISP button on the remote control to show the current information available. The following information will appear – Title Elapsed; Title Remain; Ch. Elapsed; Ch. Remain; Display Off and so on. Note: For different discs, D.DISP button may have a different function.

i. Playing in a Favorite Order

Combine your favorite titles, chapters or tracks and play them in your favorite

order.

HOW TO SET TITLES, CHAPTERS, OR TRACKS IN A FAVOURITE

ORDER

The program playback function will automatically playback titles, chapters or

tracks in the order preprogrammed.

1. Insert a disc, press the PROG button, the menu will appear on the

screen, as following:

PROG

T C

1 :

5 :

9 : :

13 :

2 :

6 :

10 :

14 : :

3 :

7 :

11 : :

15 :

4 : 8 : : 12 :

16 :

PLA CLAER

Y

2. Input the numbers to select the title and chapter (track) you want, and

then press the , , or buttons to move the cursor to input the

next one.

3. Press the ,, or buttons to select and highlight the word PLAY,

then, then press the ENTER button. The DVD video player starts

memory playback.

Notes:

When the DVD video player is switched off, or if the discs are

removed, the program item will be removed.

For different discs, PROG button may have a different function. If you press the STOP button once the DVD video player will
stop. At this point, press the ENTER button to re-start the disc from the same point. If you press the STOP button twice the program playing will be cancelled.
j. Selecting the Camera Angles Setting
This DVD video player allows you to select from several different angles. Press the ANGLE button while playing back a scene recorded with multiple angles. You may only press the ANGLE button when the angle icon appears on the DVD display. Each time you press the ANGLE button, the angle will change. Notes:
The angle function will not work on DVD video discs that do not contain recorded multiple angles.
During still playback, you are able to change the camera angle. However, when you resume to normal playback, the camera angle changes to the new settings.
The angle icon indicator will illuminate while playing back a title that contains at least one scene recorded with multiple angles.
k. Selecting Subtitles
This DVD video player allows you to display subtitles which are included on the disc. By Pressing the SUBTITLE button during playback, you have the option to select a preferred subtitle from those included on the DVD video disc. To turn off the subtitle function, press the SUBTITLE button during playback until the subtitles disappears. Notes: With some DVD discs, you may not be able to turn off the subtitles
and they will appear on screen automatically. As you press the SUBTITLE button, the subtitles may not appear
immediately during some screens.

l. Selecting languages
This DVD video player allows you to select preferred languages which are included on the Multi-languages DVD discs. By Pressing the LANG button once during playback to display current language, press the LANG button again to toggle between different language modes in sequence. Note: For MP3/CD discs playback, press the LANG button to switch between different audio channels in sequence.
m. MP3/JPEG playback
1. In DVD mode, Insert a MP3 or JPEG CD into the disc slot, the DVD video player will initialize the disc and the directory (folder) will be shown on screen. The first MP3 or JPEG file will be played automatically.
2. Press the ,, or buttons to select the folders, MP3/JPEG files or
modes and press the ENTER button on the remote control to enter the
folder or start playback.
3. When playing MP3 files, press the or buttons during playback to
skip the tracks. Notes: When playing MP3 Files, there is no picture display, only there is
audio output. When viewing the JPEG pictures, you could press the,, or
buttons to flip or rotate the picture. When viewing the JPEG pictures, you could press D.MENU button
to enter into preview mode to display 12 pictures. Press or
button to select next or last page or press the numeric buttons to
30

view the corresponding pictures.
n. INTRO playback
Press the INTRO button to play the first 10 seconds of each track when playing CD discs.
o. Customizing the Function Settings
This DVD video player allows you to customise the performance to your personal preference. DISPLAYING THE SETUP MENU SCREEN: The DVD SETUP MENU screen asks you to select a setting category from SYSTEM SETUP, LANGUAGE SETUP, AUDIO SETUP and DIGITAL SETUP. The selected category will provide you with the setting details on the TV screen. Please look at the following for more details.
Press the DVD SETUP button to enter the SETUP MENU. Press the ,, or buttons to select and highlight the category. Then press the ENTER button to confirm. Press the DVD SETUP button again to return to the root menu or to exit the setting menu. Note: Functions and menu may change without notice.
1. System Setup
TV SYSTEM This menu enables you to set the picture format for your TV/DVD between NTSC/ PAL/ AUTO according to your request and local TV system.

TV TYPE

This menu enables you to select one of the three aspect ratios: 4:3 PS / 4:3LB / 16:9
4:3PS(Normal) Normal Pan and Scan is used for most normal television broadcasts. It has an aspect ratio of 4:3. Choose this setting when viewing the movies, the picture will fill the screen but left and right edges of the picture may be cut off from the screen. 4:3LB(Normal) Choose this setting will allow you to view the movies in its original aspect ratio. The entire frame of the movie will be displayed on screen but will occupy a smaller portion of the screen. 16:9 (Wide) Choose this setting if you have a widescreen television, this setting will allow the original aspect ratio to be displayed.
Note: Playback screen size may be varied according to the disc contents. For discs with 4:3 contents, using any mode would only display 4:3
screen Screen ratio selection should be according to the connected TV or
display aspect ratio.

PASSWORD This is used to lock and unlock the RATING setting. The default setting is locked. Enter the default password”0000″ by numeric buttons, and then press ENTER button to unlock. To change the password just input 4 digits you want in unlock mode.
RATING You could set the rating options according to your preference. The rating restriction divided in eight different categories from KID SAFE to ADULT. The default setting is ADULT.
Note: please refer to PASSWORD to lock/unlock the rating setting.
DEFAULT SETTING Press the ENTER button to restore factory default.
Note: The password and Rating setting can not be restored.
2. Language Setup 33

Press the,, or buttons to select the LANGUAGE setup icon, press ENTER button to confirm. You could choose the available languages as displayed on the screen menu.
Note: Audio languages, Subtitle languages and Menu languages are DVD discs specified.
3. Audio Setup
AIDIO OUTPUT Press the,, or buttons to select the AUDIO OUT setup icon, press ENTER button to confirm.
SPDIF/OFF: No output is sent to the coaxial output. Use this option if you have not connected the coaxial output to any decoder or amplifier.
SPDIF/RAW: When selected, the raw audio contained on the disc is passed directly to the Coaxial output. Use this setting when connecting the coaxial output to a multi-channel decoder/ amplifier. (REMARK: Please note that SPDIF/RAW output is not available on this model)
SPDIF/PCM: When selected, the audio contained on the disc is passed directly to the Coaxial output in PCM format. This format ensures a very high quality but it does not support the surround sound effect. Use this setting when connecting the coaxial output to a receiver-amplifier not capable of decoding multi-channel audio.

TONE Press the,, or buttons to adjust the Tone setting.
4. Digital Setup
DYNAMIC RANGE Press the,, or buttons to adjust the compression ratio for different audio effect, When selected FULL, the peak signal value is smallest; When selected OFF, the peak signal value is biggest.
DUAL MONO Press the,, or buttons to select 4 different audio output modes: STEREO / MONO L / MONO R / MIX MONO.
VII. Other Operation

Earphone operation
This unit possesses an earphone jack. Connect your earphones to the socket and adjust the volume. Once plugged in, the speaker output will be cut off automatically.
PC audio in operation
This unit has a PC audio input jack. Connect the unit to your PC with the correct audio cable (not included). Ensure the unit is in PC mode and adjust the volume.

Trouble Shooting
Should the unit not function, please check the following table to find out the possible problem. If you still can not solve the problem, please contact the Grundig Warranty line.

a. DVD player

SYMPTOM
No sound
Disc playing abnormally

CAUSE Wrong connection or loose connection; System mute.
Disc dirty or scratched

Disc not playing Disc placed upside down

Remote control not working
Does not work

Obstacles between remote control and the sensor on the unit; Battery has no power; Too far from the TV. External interference with the CPU.

POSSIBLE CURE Check and correct all connections; Cancel mute.
Clean or change the disc. Turn the disc the correct side up.
Clear away obstacles; Change battery; Operate at a closer distance.
Pull out the plug and insert again.

b. TV/Monitor

Symptom No power
No picture
No sound
Color distortion Picture/sound have interference Remote control is not functioning
Screen glittering under PC mode Screen traversed under PC mode

Remedy 1. Check whether the power plug is connected to the power
supply. 2. Pull out the plug and wait for 60 seconds, and then insert
the power plug again and switch on the TV/monitor. 1. Check whether the antenna is connected properly. 2. Change to another channel. 3. Change the length and the contrast setting. 4. Make sure that the AV picture input cable is connected
properly. 1. Increase the volume. 2. Check whether the TV is in MUTE mode. 3. Make sure that the sound system setting is correct. 4. Ensure the AV audio signal input cable is connected
properly. 1. Ensure that the equipment is connected properly. 2. Ensure that the AV video signal input is connected
properly. 1. Check whether the equipment is connected properly. 2. Adjust the antenna if use an outdoor antenna. 1. Make sure that the batteries are installed with correct
polarities. 2. Clean the remote sensor. 3. Ensure that there is no foreign object between the
remote control and the sensor. 4. Operate the remote control at a distance no more than
6 metres from the remote sensor Reset the computer and enter into the safety mode, then select the appropriate screen type by consulting the operation manual. The phase is not appropriate. Enter into the PC setting and change to correct level.

(1) Please read these operating instructions carefully before you operate this unit.

(2) When you want to cut off the electricity supply to the unit, please press the STANDBY button on the unit, then take out the plug from the wall outlet.
(3) Don’t press any buttons if you are not using the unit. Set the STANDBY button to “OFF”, and take out the batteries from the remote control if the unit is not being used for a long period of time.
(4) Be cautious of the safe mark. (5) Repairs are to be referred to qualified service personnel. DO NOT
attempt to take apart by yourself. (6) Due to a sudden change in temperature or humidity, or when warm
air comes into contact with any cold parts in the unit, condensation may form. When condensation forms inside, the unit may not function well. Once condensation disappears, the unit will return to normal functions. Placing the unit in a warm room will help to dry up condensation. This should take 1 to 2 hours, depending on environmental conditions. As condensation may also appear on the disc, it should be wiped from the center towards the outer side using a dry cloth. (7) It is dangerous to use warped or broken discs since lasers rotate at high speed. Never use discs repaired with plastic tape or glue, as it will lead to damage. After playing, if you hear a strange noise or the unit flatters, e.g. the disc does not turn smoothly, please stop playing immediately. (8) Please remove the disc after use and put into a case, store them in a vertical position. Tilting or piling may lead to warping. Please keep the discs away from direct sunlight, high temperature and humidity. Do not stick labels onto discs. Do not scratch the surface of discs.
IX. Maintenance
1). Cleaning the cabinet Use a soft cloth slightly moist with a mild detergent solution. Do not

use a solution containing alcohol, spirits, ammonia or abrasives. 2). Cleaning discs When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre outwards. Do not use solvents such as benzine, thinners, commercially available cleaners or antistatic spray intended for analogue records.
WARNING:
To prevent fire or shock hazard, do not expose this unit to rain or moisture. Do not remove cover, no user serviceable parts inside, refer servicing to qualified service personnel.

X. Specifications

Model No.

GLCD2206HDV/GLCD2206HDVW/ GLCD2206HDVB/GLCD2206HDVR/ GLCD2206HDVS

Screen size

22 inch

Screen format 16:9

Resolution

1680*1050

LCD

Contrast Brightness

1000:1 300 cd/m

Display colours 16.7M

View angle

170° (horizontal) / 160° (vertical)

Response time 5 ms

TV system

DTV: DVB-T

ATV: PAL I/BG/L/DK

DTV decode

Audio: MPEG2 Audio Layer I&II Video: MPEG2 Transport MP@HL

TV

Demodulator : COFDM

DTV de-mod.

OFDM Mod.: 2K, 8K FFT, SFN and MFN Packed Carries: 2K/8K

Guard Interval: 1/4, 1/8, 1/16, 1/32

Tuner

Integrated and frequency synthesis

DVD Compatible with CD/MP3/WMA/JPEG/VCD/DVD formats

Coaxial

X 1

Video

X 1 ( CVBS)

Terminals S-Video

X 1

VGA

X 1

HDMI

X 1

Audio L/R

X 1

YPbPr

X 1

Audio output

2 X 3W (rms)

Gross weight

8.6 Kgs

Power supply

DC 12V 5A, AC110~240V, 50Hz/60Hz

Power Consumption

Max 60W

Design and specifications are subject to change without prior notice.

Model No.

LCD

Screen size

Screen format

Resolution

GLCD1906HDV/GLCD1906HDVW 19 inch 16:9 1440*900

40

Contrast

700:1

Brightness

300 cd/m

Display colours 16.7M

View angle

160° (horizontal) / 160° (vertical)

Response time 8 ms

TV system

Digital: DVB-T/ Analog: PAL I/BG/L/DK

DTV decode

Audio: MPEG2 Audio Layer I&II Video: MPEG2 Transport MP@HL

Demodulator : COFDM
TV
OFDM Mod.: 2K, 8K FFT, SFN and MFN DTV de-mod.
Packed Carries: 2K/8K

Guard Interval: 1/4, 1/8, 1/16, 1/32

Tuner

Integrated and frequency synthesis

DVD Compatible with CD/MP3/WMA/JPEG/VCD/DVD formats

Coaxial

X 1

Video

X 1 ( CVBS)

Terminals S-Video

X 1

VGA

X 1

HDMI

X 1

Audio L/R

X 1

YPbPr

X 1

Audio output

2 X 3W (rms)

Gross weight

7.4 Kgs

Power supply

DC 12V 5A, AC110~240V, 50Hz/60Hz

Power Consumption

Max 60W

Design and specifications are subject to change without prior notice.

XI. Display modes

Resolution 720×400 640×400 640×480(VGA) 640×480(VGA)

Horizontal Freq. (KHz) 31.5 31.5 31.5 37.9

Vertical Freq. (Hz) 70 70 60 72

640×480(VGA)

37.5

75

800×600(SVGA)

37.9

60

800×600(SVGA)

47.2

72

800×600(SVGA)

46.9

75

1024×768(XGA)

48.4

60

1024×768(XGA)

56.5

70

1024×768(XGA)

60.0

75

1280×1024(SXGA)

63.5

60

1280×1024(SXGA)

80.0

75

1. Modes, which are not listed in the above table, may not be supported. For an optimal picture it is recommended to choose a mode listed in the table.
2. You have 13 available modes compatible with windows. 3. It can happen that the image is disrupted. This can occur as result of a
signal from the VGA card, which does not correspond with the usual standard. This is not, however, an error. You can improve this situation by altering any automatic setting or by manually changing the phase setting and the pixel frequency menu. 4. If you switch off the TV/monitor, interference lines can occur on your screen. But it’s not a problem, no need to concern about it. 5. To extend the service life of the product, we recommend that you use your computer’s power management function. Note: Design and specifications are subject to change without notice.

Warranty

Please keep your receipt as proof of purchase. This product is warranted for any defect in materials or workmanship for three years after the original date of purchase. This product is for normal domestic and office use only. This warranty does not cover damage from misuse or neglect , accidental damage, vermin infestation, excessive voltages such us lightning or power surges or any alternation that affects the performance or reliability of the product.

In the unlikely event that your product fails to work normally, please contact Grundig Warranty on 1800 509 394 (Australia) or 0800 450 259 (New Zealand) and have your receipt of purchase on hand. This guarantee is subject to the following provisions: It is only valid within boundaries of the country of purchase; The product must be correctly assembled and operated in accordance with
the instructions contained in the manual; This product must be used solely for domestic purposes; The guarantee does not cover accidental damage; The guarantee will be rendered invalid if the product is resold or has been
damaged by inexpert repair; The manufacturer disclaims any liability for incidental or consequential
damaged. This guarantee is in addition to, and does not diminish, your statutory or legal rights.
PO BOX 6287 Silverwater NSW 1811 www.grundig.net.au Grundig Warranty: 1800 509 394 Australia Grundig Warranty: 0800 450 259 New Zealand

PO BOX 6287 Silverwater NSW 1811 www.grundig.net.au

Ver. 5 13-AUGUST-2009