MarCum TECHNOLOGIES LX-9 Digital Sonar Unit User Manual
- June 16, 2024
- MarCum TECHNOLOGIES
Table of Contents
MarCum TECHNOLOGIES LX-9 Digital Sonar Unit
Product Information
Specifications
- 8 LCD Monitor
- Dual Beam Transducer (switch between 20 degrees and 8 degrees)
- Rugged transport shuttle with extendable transducer arm
- Padded nylon soft pack for protection
- Auxiliary clip-on camera soft pack
- Protective clear snow shield
- 12 volt 9 amp battery with automatic 3-stage charger
- 2-year warranty
- Adjustable zoom
- Dashboard Display for critical information
- Five different sonar windows to choose from, displaying up to three at once
- Sony Super HAD II CCD underwater camera with 75′ of cable
- Built-in DVR recording system with SD card
- Camera Panner
- Transducer offset setting
- Sun Shield
Product Usage Instructions
Getting Started
The LX-9 Digital Sonar Unit offers both sonar and video features. It is
recommended to familiarize yourself with the unit’s menu and functions before
using it in the field. Start by learning how to use the sonar feature.
Battery Charging
To charge your battery:
- Connect the charger to the battery.
- Plug the charger into a power source.
- Allow the battery to charge fully. The charger has an automatic 3-stage charging system.
Setting the Transducer
Follow these steps to set up the transducer:
- Attach the transducer arm to the rugged transport shuttle.
- Position the transducer arm in the desired location.
Moving the Transducer
To move the transducer:
- Release the transducer arm lock.
- Reposition the transducer arm as needed.
- Lock the transducer arm in place.
Fishing in Shallow Water
When fishing in shallow water: Adjust the sonar settings to optimize
performance.
Reading through Ice
To read through ice: Adjust the sonar settings accordingly.
Power Sensitivity Range
The LX-9 allows you to adjust the power sensitivity range for better
detection. Zoom The unit offers an adjustable zoom feature for a closer look
at specific areas.
Interference Rejection
Utilize the interference rejection feature to minimize signal interference
from other devices or sources.
Target Adjust Up/Down
Adjust the target position on the display to match the actual location.
Menu/Enter
Use the Menu/Enter button to access and confirm menu options.
View Mode
Select the desired view mode to display different sonar windows.
Display Options
Customize the display options according to your preference.
Play/Record
The LX-9 features a built-in DVR recording system. Use the Play/Record
function to capture and review sonar and video footage.
Sonar Settings
Adjust various sonar settings to optimize performance based on your fishing
conditions.
Systems Settings
Access and customize system settings to personalize your experience with the
LX-9.
LX-9 USER’S GUIDE
You talk, we listen. For years we have been getting requests for a combined
sonar/video unit. Not two displays stacked on each other, mind you, but an
all-encompassing unit that will locate, track, and ultimately help you catch
more fish.
The LX-9 is not for everyone. There are plenty of anglers out there who prefer the mobility of one of our lean and mean sonars. Some people only fish in environments where an underwater viewing system is the way to go. Believe it or not, there are even some anglers in a few remote corners of the ice belt who fish with no electronics at all. But if you want the best, a combination of all the features that anglers have been asking for, you’ve found it.
Fishing with sonar requires the angler to use a bit of imagination to envision what is going on below. Using the video features of the LX-9 alongside the sonar will give anglers a chance to see what the sonar signals represent, ultimately making you a better angler. The LX-9 features the cutting-edge sonar of the LX-7 fused with the living color imagery of our VS825sd underwater viewing system. And with its built-in DVR, you will be able to preserve and share every minute of the action.
FEATURES
- 8” LCD Monitor—there isn’t a Fish-finder/Viewing System that is easier to see!
- Dual Beam Transducer—Quickly switch between 20 degree and 8 degree
- Rugged transport shuttle with extendable transducer arm
- The padded nylon soft pack offers the ultimate in protection
- Auxiliary clip-on camera soft pack
- Protective clear snow shield
- 12 volt 9 amp battery with automatic 3-stage charger
- 2-year warranty
- Adjustable zoom
- Dashboard Display keeps the angler updated with critical information
- Five different sonar windows to choose from, displaying up to three at once
- Display Sonar signals on top of the video for an unbelievable “Heads –Up” display
- Sony Super HAD II CCD underwater camera with 75’ of cable
- Built-in DVR recording system w/ SD card
- Camera Panner
- Transducer offset setting
- Sun Shield
GETTING STARTED
Sonar, Camera, or Both? That is the big question, and we hope that you utilize all that the LX-9 has to offer. We strongly recommend that you put the LX-9 through its paces while at home, just to learn the “flow” of the menu and the various functions. While one of the best features of the LX-9 is the ability to display a sonar overlay on top of your video or play video and sonar side by side, let’s start by learning how to use the sonar.
Anglers who are new to using digital sonars sometimes struggle with learning how to use them. A “fear” of pressing buttons can slow down the learning curve. When learning how to use your LX-9, press away! You can’t hurt or break your system by pressing buttons, and if at any point you feel that you want to start over, go to System Settings in your menu and select “Restore Factory “ to go back to the screen configuration that came from the factory.
To get started, remove the LX-9 from the packaging, and open the top cover of the soft pack by lifting the Velcro closures on each side and front of the soft pack. Once opened, loosen the knobs on either side of the gimbal bracket, and the monitor can now be positioned how you want it. Once the monitor is positioned how you want it, tighten the knobs again to hold the monitor in place. The front panel of the soft pack can be folded up and secured behind the monitor with the hook and loop fasteners.
Look behind the monitor and hook up the LX-9’s power cord to the battery. While you are at it, remove the entire unit from the soft pack so you can see exactly how everything connects—this makes it easier down the road if you ever need to change a battery, transducer, or camera. Your LX-9 is delivered with a 9 amp battery that is charged, so you can take it fishing right away. Even though the battery comes with a charge on it, due to storage time or other factors it may not be fully charged when you get it, so if you are not going fishing immediately you should hook up the charger to make sure the battery has a full charge. To charge the battery, see below (pg. 3). The Marcum LX-9 will operate for 8 hours or more on a fully charged battery. If you are going to be in a situation where you will want to use your system for more than one day without recharging, having a second, fully charged battery with you is cheap insurance that will allow you to get full use out of your system for the duration of your trip.
The LX-9 comes with a camera that is stored in a removable camera bag. The camera easily connects to the monitor by plugging the camera cable into the camera adapter cable coming off the monitor. If you are going to be in a situation where you will not be using the camera, you can easily detach the camera and the camera bag from the main unit.
Be sure to explore all of the options available to customize your Dashboard Display. With five different sonar portals, four color palettes, 2 cone angles, and a myriad of other settings, there are many possibilities. It is easy to explore these options, and you can set the LX-9 so that it defaults to your preferred arrangement. Changing your settings is easily done on the fly, but experimenting while using the simulator at home will help you learn the “flow” of the menu and settings.
BATTERY CHARGING
Your Marcum system comes with a 3-stage battery charger. This style of charger has proven to be the most effective and easiest to use of all charging systems available. Because this is a 3-stage charger, there is no danger of overcharging your battery. When properly cared for, a sealed lead acid battery will last for at least a couple of years. Batteries are made to be used, and they need to be used to make the most of them. The most important thing you can do is to promptly recharge your battery after each use. Not charging your battery immediately after use is the number one thing that leads to battery failure.
For safety reasons, it is recommended that you place your system on a flat, hard surface like cement or tile when charging it, away from any flammable materials. Be sure to disconnect the charger from the wall when not in use, and avoid leaving your battery hooked up to the charger for extended periods.
When you get home from a trip, put your battery on charge right away and leave it there overnight, or for around 8-12 hours. Likewise, on the night before an ice fishing trip put it on the charger again, just to make sure. Again, there is no danger of overcharging your battery. We often talk to people who hesitate to charge their battery after each use for fear that the battery will develop a “memory” and this will lead to a shortened run time—THIS IS FALSE!!! ALWAYS CHARGE YOUR BATTERY AFTER EVERY USE!!! Be sure to use the charger that came with your system, or a similar one that is between .5 amp. and 1 amp. Using a larger charger, like you would use on a car, truck, RV, or boat is likely to cause damage to the battery. There is no danger of overcharging your battery with a low amp charger, and most chargers automatically go into “maintenance mode” once a full charge has been achieved.
TO CHARGE YOUR BATTERY:
Your battery has a wiring harness attached to it that has “piggyback”
terminals on it, enabling you to keep the power cord from the unit attached to
the battery at all times, as well as having the wiring harness with a
receptacle for your charger attached at all times. To charge, simply couple
the end of the charger with the end of the wiring harness. It is normal for a
green light to appear on the charger at this time if the charger is plugged
into the battery only. It is also normal for the light on the charger to be
green if it is just plugged into the wall. When it is plugged into the wall
and battery, you will see a red LED light appear on the charger. If the light
is red, the battery is being charged. When your battery is fully charged, this
red light should change to green. If it is time to go fishing and the light
has not turned green, go fish and try to allow a longer charging period next
time.
Batteries are an expendable item and must be replaced periodically. The batteries that we use are the “Sealed Lead Acid” variety, they are 12 volts and range from 7 to 9 amps. The more amps the battery has, the longer it will run on a full charge. Your Marcum can be powered off of any battery that is 12 volts, even a large automotive or deep cycle battery.
- If you are having difficulty with the charging process, please see the Charger Troubleshooting section at the end of the manual (pg. 20). Also, you can watch a video tutorial on charging your battery by following the below link. http://helpdesk.marcumtech.com/MarCum/Knowledgebase/Article/View/72/6/redgreen-light-on-your-charger
- If you need to remove the battery, slide the power cord from the battery. Remove the strap that is holding the battery in place and lift the battery out. To replace the battery, place a new battery of similar specifications into the battery compartment secure it with the Velcro strap, and re-connect the positive and negative terminals.
SETTING THE TRANSDUCER FOR ICE FISHING
When used in conjunction with the retractable pivoting transducer arm and
rubber stopper, the LX-9’s transducer will automatically level itself in your
ice hole. To begin operation, take the transducer out of the recessed holder,
and rotate the adjustable ice arm out from inside the shuttle. Extend the
transducer arm, (the cable should already be threaded through it with stopper
in place) and deploy the transducer into the water. We recommend setting your
stopper to have the transducer down the least amount possible. The LX-9 puts
out enough power that in most cases it is not necessary to have your
transducer down more than a few inches below the water line to get a good
reading. When the ice thickness is over two feet, it may be necessary to have
your transducer set somewhat farther down. Remember–the less transducer cable
you have out, the easier it is to pull it out of the water when bringing in a
fish or to move to a new location. Under no circumstances should you ever have
the ducer below the ice—this can lead to the ducer becoming damaged.
It is also important that you keep the cable near the center of the ice hole. We frequently hear from anglers who allowed their cable to freeze into the side of the ice hole. If this should happen to you, make sure the unit is turned off before attempting to chisel it out. If you accidentally cut the ducer cable, do not try to use that ducer again.
MOVING THE USER TO A NEW LOCATION
Being mobile is one of the keys to being successful on the ice. Whenever you
move from one spot to another, it is tempting to leave your transducer hanging
on the transducer arm. This is likely to lead to failure of the transducer arm
and can cause damage to the transducer itself. Always stow the transducer
inside the pack when you are moving. Keeping the amount of transducer cord you
have out at a minimum will make transporting your Digital Sonar easier.
Similarly, you may need to quickly remove your transducer from the hole when
about to land a fish. We have seen anglers in a panic grab the shuttle itself
and toss the entire unit to the side. This is no way to treat any piece of
electronics; a much better approach is to simply lift the transducer out of
your way by the cord, and the shuttle itself can be gently pushed aside.
Whenever you are moving via sled or vehicle, always fold up your transducer
arm, stow the transducer inside, and close the protective soft pack.
FISHING IN SHALLOW WATER
The LX-9 is designed to be an effective fishing tool in a wide variety of
environments. Most of the time, simply turning on the unit at factory default
settings is all that is necessary. Shallow water [10 feet or less] can be
problematic without making a few adjustments. If you are having trouble
getting optimal performance out of your Digital Sonar in shallow water, here
are some adjustments to experiment with. Depending on the actual
circumstances, one or more of these adjustments may be necessary. First thing,
when in shallow water, keep your transducer near the surface of the water [at
the TOP of the ice, almost in the air] no matter how thick the ice is. This
gives the user a little more room to “work”. Be sure that you manually select
the 10-foot range. Next, press the MENU button, select SONAR SETTINGS, and
then scroll to SONAR MODE. Highlight it and select OPEN WATER MODE. We realize
it does not seem natural to use “OPEN WATER MODE” when you are on the ice, but
making this change will “back off” the gain curve, allowing better performance
in certain ice fishing conditions. Also, try lowering the MAX PING RATE to 1.
Finally, you should also consider changing the color palette from the default
“SIX- COLOR” to one of the three-color palettes.
READING THROUGH ICE
The Marcum LX-9 will provide accurate information reading through ice
providing the ice is reasonably clear. Wet the ice with at least a cup of
water to improve the coupling of the transducer to the ice. Place the face of
the transducer firmly on the wetted ice, and you will now be able to see the
depth displayed digitally, and a signal showing the bottom (and fish) on
whichever sonar windows you have open. Drilling into the ice 1-2” before
taking a reading may be necessary if the surface of the ice is very rough, or
if the ice is filled with air bubbles.
OPERATION
The LX-9 has many functions and settings that are selected or changed by
buttons on the Control Panel. Learning what each of the buttons (POWER, SENS,
RANGE, ZOOM, IR, CONE ANGLE, TARGET ADJUST, MENU/ENTER, UP, DOWN) does will
enable you to get the most out of your LX-9. Note that you can experiment with
different settings and dashboard arrangements in SIMULATOR mode. Many of the
selections will activate just by highlighting your desired setting.
CONTROL PANEL
The following is an explanation of each button on the control panel and what it does. Some of the button functions can also be accessed in the main menu. Pressing any of the Control Panel buttons will cause a window to open, enabling the user to make the desired adjustments. All button function windows will time out after about 6 seconds. Any changes made to the settings will activate when the MENU button is pressed or after a few seconds without activity.
You may experiment with settings by getting your Digital Sonar to get a bottom reading off the floor in your house or garage. It must be a bare tile or cement floor. Position your Digital Sonar with the transducer hanging motionless about 2 feet above the tile or cement floor and then turn the sensitivity up to the maximum [25] setting. If the user is 2 feet above the floor, you should get a bottom reading at about 8.5 feet [the unit is calibrated to be accurate in water, not air!]. If you now raise and lower the ducer, the bottom signal should move correspondingly. You may find it is easier to learn the zoom and other functions while experimenting in this way with the “manual simulator”.
-
POWER
Press and hold this button for about 2 seconds to turn your unit on or off. When you first turn the unit on, it may take 30 seconds or slightly more for the screen to fully illuminate. -
SENS
The SENS (sensitivity) button controls the amount of sensitivity required by the unit to pick up objects like bottom, weeds, fish, smaller bait fish, or small lures and jigs. The lower the number, the less sensitivity, conversely higher numbers mean more sensitivity. To adjust your sensitivity, first press the SENS button, and a bar will appear at the bottom of your display. Pressing the UP/DOWN will adjust your sensitivity, and the sensitivity setting will now be digitally displayed on the SENS gauge. The best SENS setting is achieved by turning up your sensitivity from 0 until you receive a clear and steady bottom reading. To see your lure or bait, turn up the SENS some more until you just begin to display your bait without it fading or flickering on the screen. The sensitivity will go up to 25, but a setting between 5 and 10 is likely to be where you want it set in most instances. Too much sensitivity will only display unnecessary information, showing clutter and making it more difficult to interpret the return signals. Clutter can be caused by any number of suspended items, including algae, zooplankton, tiny bubbles, and other particles. -
RANGE
The LX-9 is equipped with 4 range options–“Auto ”, “Manual ”, “Dynamic ”, and “Manual Dynamic”. Regardless of the depth range setting, your LX-9 will always display digital depth, even if the bottom is deeper than the bottom limit of the RANGE setting (down to 300’).
You should familiarize yourself with how the different range settings work. If you ever experience jumpiness or erratic behavior on your display, it could be caused by environmental conditions like irregularities on the bottom, weeds, steep drop-offs, big schools of fish, etc. causing the Auto Range function difficulty in discerning what the actual depth is. If you encounter this, change to one of the manual range selections.-
AUTO RANGE
the Auto Range feature allows you to simply turn on the unit and begin fishing. To enter Auto Range, press RANGE. Now use the UP button to highlight “Auto”. Now press MENU, and the LX-9 will automatically lock into the appropriate depth range. For instance, in 32 feet of water, the LX-9 will lock into the 40-foot range. In 45 feet of water, the LX-9 will automatically lock into the 60-foot range. -
MANUAL RANGE
there are 9 manually adjustable depth ranges—10, 20, 40, 60, 80, 120, 180, 240, and 300 feet. If you manually select a range, select a range that is deeper than the actual depth, and when in doubt, error on the “deep” side. To manually adjust the LX-9’s depth range, press RANGE, and then select MANUAL. This will open a window with 9 range options. Your selected range will lock in as soon as the selected range has been highlighted. -
DYNAMIC DEPTH
this Marcum exclusive feature functions similarly to the “Auto Range”, but fine-tunes your range even further. The Dynamic Depth will maximize the space on your display by utilizing a constantly variable range that will always be just slightly deeper than the actual depth. For example, if you were fishing in 23 feet of water, the Dynamic Depth range would be 25 feet, if you were in 29 feet of water, the Dynamic Depth range would be 32 feet. The Dynamic Depth range will not go shallower than 10 feet. -
MANUAL DYNAMIC
this takes the Dynamic Depth feature even further, you can manually select the max range in one-foot increments. Press RANGE, then use the UP/DOWN keys to select what you want to be the max depth, probably one foot deeper than the actual depth. The Manual Dynamic Depth range will not go shallower than 10 feet. This is probably the range option you will use the most.
-
-
ZOOM
The ZOOM button allows you to select the upper range of the portion of the water column you would like to zoom in on. The actual size of the Zoom window can be adjusted in the Main Menu. The Zoom feature allows you to focus the display on a specific depth within the water column and can be a great benefit in a variety of fishing situations. See the separate ZOOM section below for more info on the ZOOM. Whenever you are utilizing the Zoom menu, keep in mind that the menu will “time out” after 6 seconds. -
IR (INTERFERENCE REJECTION)
The Interference Rejection system is designed to suppress competing return signals from other sonar units being used within proximity. When other sonar units are causing interference with the display of the LX-9, activate the IR feature by depressing the IR button located on the control panel of the LX-9. Interference is indicated by unusual signals flashing or scrolling across your display.
There are 12 levels of interference rejection. Press the IR button once to open the IR window, now use the UP/DOWN buttons to select the desired level of IR. The correct level of IR will be achieved when the display is clear of display clutter. In some extreme cases, clutter will be greatly reduced but not eliminated.
Anytime two or more sonars are being operated in proximity to each other, there is the potential for interference. Deep water and hard bottom will increase the likelihood that one or more of the competing sonars will experience interference. Besides experimenting with different levels of IR, the anglers experiencing interference can also try having their transducers set at different levels, going to narrow cone angles, and reducing gain or sensitivity settings. -
TARGET ADJUST
this feature allows the angler to change the size of the signals being displayed without increasing the sensitivity. Depending on the angler’s preference, the signal size can be easily changed from a razor-thin line to a thicker band. The TARGET ADJUST feature will give you the thinnest, smallest, signal size at “0”, and the signals displayed will get thicker as you increase the TARGET ADJUST. This feature should be used in conjunction with the SENS to fine-tune your display. Anglers who have a hard time seeing, as well as those who fish from a standing position, will appreciate the “TARGET ADJUST” feature. -
UP/DOWN
these buttons will scroll through various sub-menu options. The DOWN button also functions as a “Hot Key” for making recordings. If you press the down button before opening the Menu, you will start a recording. This “Hot Key” exists to make it easy for the user to start and stop a recording with the pressing of one button. -
MENU/ENTER
This button enables you to access other functions of the LX-9. Some of these functions are also accessible through the use of the other buttons on the Control Panel. When you press the MENU button, five sub-menus will be revealed.
They are:- View Mode
- Display Options
- Play/Record
- Sonar Settings,
- System Settings
-
VIEW MODE
The following features may be adjusted here:-
SONAR
for when you want to use the SONAR functions only -
CAMERA
for when you only want video from the camera displayed -
HEADS UP
this configuration has each of the vertical displays on top of the video SPLIT SCREEN—this configuration is a split screen, with video on the left and the two vertical displays on the right
-
-
DISPLAY OPTIONS
The following functions can be adjusted here:-
FLASHER DISPLAY
The Flasher Display can be turned on or off here VERTICAL DISPLAY The Vertical Display can be turned on or off here -
VERTICAL ZOOM DISPLAY
The Vertical Zoom Display can be turned on or off here -
CHART DISPLAY
The Chart, or Scrolling graph, can be turned on or off here -
CHART ZOOM
This enables you to use the scrolling graph in zoom mode -
GAUGE DISPLAY
Your 5 gauges, on-screen displays for the camera, and Sonar Footprint may be turned on or off here -
TEMPERATURE
The water temperature display may be turned on or off here. This feature will only work if you are using your unit with the optional “Universal Sonar”, designed for open water use. -
BACKLIGHT
You can adjust the overall brightness level of the display here. When using outside during bright conditions, you will want to have it set fairly high, at 50 or more. In low light or when used inside an ice shack, a setting of 50 or less is desirable. -
COLOR PALETTE
There are four different color palettes to choose from. See the section below on Color Palettes below for more info. -
BACKGROUND
There are three different backgrounds to choose from. The “Night” option is great for low-light periods or when in a darkened shack.
-
-
PLAY/RECORD
This is where all recording and playback functions are done.-
LIVE
This gives you a live video feed. You can start and stop a recording anytime you are in “LIVE” mode by pressing the “HOTKEY” which is the down arrow -
SIMULATOR
The LX-9 has a simulator mode that will portray a variety of different depths and signal returns. Activating this feature enables the user to experiment with the various settings without actually being on the water. This simulator represents an open-water experience, so the depths and signals will change as it goes through the simulation. To turn the simulator off you must go back to “LIVE” mode. -
PLAYBACK
This is to review the video recordings you have made. The recordings will display as thumbnails, with your most recent video at the bottom. Use the UP and DOWN arrows to highlight the desired clip, then select PLAY -
RECORD
This is to begin a recording. A red dot will appear in the lower right corner of the screen when the unit is recording. -
STOP
This is to stop a recording; the red dot will disappear when the recording function is stopped -
DELETE
When this is selected, your thumbnails will appear, and one will be highlighted. Pressing MENU at this time will delete the unwanted file. If you do not want to delete a file, wait for this screen to time out.
-
-
CAMERA ADJUST
Various camera/video functions can be adjusted here. They are as follows:-
Brightness
lightens up the video -
Contrast
makes the light things lighter and the dark things darker -
Saturation
makes the colors more vivid -
Color Kill
turns off the color, and allows for Black and White viewing. NOTE: The Color- kill feature will turn on automatically when the camera’s light sensor doesn’t detect enough light for optimal color viewing. This can happen in low light conditions, in deep water, or when the ice is very thick and/or covered with snow. -
Camera Light
The LED camera light is turned on and off here -
PRE-RECORD
This Marcum exclusive feature allows you to capture video AFTER the event has happened. You can wait until after you catch or see a fish to hit the record. You will then have saved a “Loop” of video. You first select the length of the loop you want. Immediately after you catch a fish, save the loop by pressing the “HOTKEY”, which is the down arrow.
SD ACCESS Selecting this allows access to the following settings: -
LX-9
When you want to use the LX-9 without an external monitor -
External
This allows the video feed to be sent out to an external monitor. Video and sonar will only be visible on the external monitor and the screen on the LX-9 will go dark when this function is selected. -
Eject SD
Be sure to select this option before removing the SD card -
Format SD
This will format a new SD card, or erase all videos that are on the card Whenever you select the PLAY/RECORD menu, a white rectangle will appear that shows how many recordings you have, and how much space is left.
-
-
SONAR SETTINGS
The following features may be adjusted here:-
SENSITIVITY
This adjusts the sensitivity. This is described in the Control Panel section above -
RANGE
Select the range in the same manner as described above -
ZOOM DEPTH
Here is where you set the upper range of the zoom window. This can also be done by using the ZOOM button as described above. The actual size of the zoom window is adjusted in the “Zoom Window” field. -
ZOOM WINDOW
Here is where you determine the size of the Zoom Window. Go to the “Zoom” section of the manual for more specific information. -
IR
Interference Rejection can be adjusted here, as well as by using the Control Panel button. See above for more info.
-
-
TARGET ADJUST
Target Adjust can be adjusted here, as well as by using the Control Panel button. See above for more info.-
CONE ANGLE
Cone Angle [and Sonar Footprint] can be adjusted here, as well as by using the Control Panel button. See above for more info. -
SONAR MODE
Choose between “ice fishing” and “open water” mode here. Despite what the two sonar modes are named, there are times when open water mode may be beneficial while ice fishing, and vice versa. An example: If you are ice fishing in water that is 10 feet deep or less, you may find that the unit works better in open- water mode. -
MAX PING RATE
Adjusting this setting will increase the response time of signals from your transducer to the screen. If fishing shallow water (less than 20 feet) use the lower settings. Likewise, you will see better performance with the higher settings in deeper water. -
CHART ENHANCE
Open-water anglers in particular will find it very helpful for locating bottom-hugging fish. The chart draws a fine yellow line on the bottom, this makes it easier to differentiate between a fish and a high spot on the bottom. Increasing the setting will “pull” the yellow line farther off the bottom. The Chart Enhance settings go up to ten, we recommend if you use it to go no higher than 2 or 3. -
TRANSDUCER OFFSET
By setting this at the same distance your transducer is below the water line, you will have the most accurate depth measurement possible. Remember that you should always have your ducer down as little as possible; often just a couple of inches below the waterline is adequate. This reduces tangles with fish and makes it easier to move from hole to hole -
SHALLOW ALARM
For open water use, this will indicate if your boat goes shallower than a designated depth. For instance, you may not want your boat to be in water less than 5 feet deep. Set the Shallow Alarm for 5 feet, and an alarm will go off if you get into water 5 feet or less. This should not be used as an aid to navigation, pay attention to your surroundings at all times! -
The alarm will stop once the boat has moved to deeper water or the settings have been adjusted to a shallower depth.
-
-
SYSTEMS SETTINGS
The following features may be adjusted here: -
LANGUAGE
Choose between English and French -
UNITS
Change between Standard and Metric measuring units -
LCD COMPASS CALIBRATION/CAMERA COMPASS CALIBRATION
- If the directional arrow for your camera becomes inaccurate, it may be necessary to recalibrate the compass. These two features are used together to accomplish recalibration. First, have your monitor on a level surface like a countertop, and have the camera hanging freely about two feet below.
- To re-calibrate, go to SYSTEMS SETTINGS, and then highlight CAM COMP CAL. Select ON, and press MENU/ENTER.
- Now rotate the camera two full revolutions and back while keeping it level. Go back to CAM COMP CAL in the menu, and select OFF.
- Next, go to SYSTEM SETTINGS, and then highlight LCD COMP CAL. Select ON, and press MENU/ENTER.
- Now slowly rotate the monitor on a level surface two full revolutions. Go back to LCD COMP CAL in the menu and select off. Your directional arrow should now be accurate.
-
RESTORE FACTORY
This is where you can restore factory settings. If at any time of changing your selections, you want to revert to this screen, you may easily do so here. -
VIDEO OUT
This allows the video feed to be sent out to an external monitor. The screen on the LX-9 will go dark when this function is selected, all displays will now be on your external monitor. If you select this when there is no external monitor hooked up, you will have to turn the unit off and then back on again, as you will not be able to view the monitor.
OTHER LX-9 FEATURES
COLOR PALETTES
Use this feature to choose which of the 4 color palettes you prefer. The
default setting has RED as representing the strongest signal, often signifying
a hard bottom or a larger fish that is in the center of the transmit signal
(cone). This is followed by ORANGE, YELLOW, LIGHT GREEN, GREEN, and BLUE.
These represent a softer bottom or smaller fish in the middle of the transmit
signal or a larger fish on the outside of the transmit signal. When using the
other color palettes, the colors displayed and the signal strengths
represented will change accordingly.
GAUGES
A feature unique to the LX-9 is the ability to be able to constantly see where
your most critical settings are. At a glance, you will be able to tell what
your Sensitivity is at, what level of IR you are operating at, how high your
Target adjustment is, your range, and battery status displayed in volts. If
you have the camera operating, you will also see camera depth and temperature.
The gauges can be turned on or off by pressing MENU, highlighting “Gauge
Display”, and making your selection. Where the gauges display will depend on
which screen configuration you have selected. Gauges cannot be displayed if
you are only operating one or both of the scrolling graphs, and in “Heads Up”
and “Split Screen” view mode some of the graphics will not be visible. None of
the gauges will display in “Camera Mode” other than camera head temp, camera
head direction, and camera head depth.
-
SENS
The SENS (sensitivity) gauge shows the sensitivity level you have selected. -
IR
The Interference Rejection system is designed to suppress competing return signals from other sonar units. -
TARGET ADJUST
This feature allows the angler to change the size of the signals being displayed without increasing the sensitivity. -
VOLTAGE
This gauge indicates the voltage currently being produced by your battery. The LX-9 needs at least 11 volts to properly operate. If the voltage drops below 11 volts, you may see a decrease in performance -
SONAR FOOTPRINT
Displays the actual extent of coverage by your transducer while you are fishing.
ZOOM
One of the best features to have in an ice fishing Sonar is “Zoom”, and there
is none better than that of the Marcum Digital Sonars. A Zoom feature enables
you to have a magnified view of a selected portion of the water column. Note
that when the ZOOM window is open, you can still view the entire water column
on one of the other windows. Imagine that you are fishing for walleyes in 30
feet of water, and you are zoomed in on the bottom 5 feet. If a school of
crappies comes through at 20 feet, you will be able to easily see them on one
of the other windows, and quickly raise your bait to their level. The position
of the ZOOM window is adjustable in one-foot increments. The ZOOM can focus on
the bottom (for detecting bottom-hugging fish), or at any level above the
bottom.
The LX-9 also offers Auto Bottom Track Zoom that automatically zooms and locks onto the bottom, even when you change locations. This is especially useful for if you are hole-hopping for bottom-hugging fish like walleyes and perch. To access the Auto Zoom, press ZOOM, and then press the UP button until “A” (Auto) appears. It will appear after you pass “0” on the Zoom Window.
The ZOOM feature on the LX-9 can be accessed in several ways depending on which sonar windows you have displayed on your dashboard. Having your LX-9 set at the factory default setting for a screen configuration will make it easiest to learn how to use Zoom. It is highly recommended that you learn how Zoom works while in simulator mode.
Operating the Zoom is quite simple, and only requires the pressing of a few buttons to select the size and position of your Zoom Window.
So, start by having the factory default screen (Flasher in center, Vertical Display on left, Vertical Zoom on right) open. The area that is featured on the Zoom Display is indicated by the “Zoom Indicator Bar”, a light blue bar on the right side of the Vertical Display. When you press the ZOOM button, a “Zoom Depth” window will appear at the bottom of the screen. This is where you set the uppermost limit of the Zoom Display by pressing the UP/DOWN buttons. When you have the desired depth highlighted, pressing ZOOM again will establish that depth at the top of your Zoom display. You will notice that the Zoom Indicator Bar will move up or down as you make these adjustments. To set the size of what is shown in the Zoom Display, press MENU, and then highlight “Zoom Window”. You can now select which size zoom window you want.
Another tip: on the left side of your “Zoom Window” are depth indicators. These indicate the portion of the water column you are looking at in the Zoom window. You need to make sure that your water depth is in between the top and bottom depth indicators. If you are in 30 feet of water and want to use a 10-foot zoom window on the bottom, a good place to have your zoom window would be about 21’ at the top and 31’ at the bottom. That will ensure that the bottom of the water column is completely covered.
Going through this process several times before you go fishing is a great idea, as that will allow you to easily and quickly make adjustments right away once on the water.
If you have only the Flasher Display, the Vertical Display, or the Scrolling Graph Display open, and go into zoom mode, pressing the “ZOOM” will cause the vertical zoom window to appear, and a “Zoom Depth” window will open at the bottom of the screen. You will still set the uppermost limit of your zoom window here, but you won’t have the advantage of having the Zoom Indicator Bar to show you exactly what area is being highlighted. With a little bit of experience, you’ll find this to be quite easy to do. Just set the zoom depth for 5, 10, 20, or 40 feet above the bottom, and then set the Zoom Window to the appropriate size. For example, if you were fishing in 30 feet of water and wanted to zoom in on the bottom 10 feet, press ZOOM, and then set the zoom depth for 20 feet (10 feet off the bottom). Now press MENU, highlight “Zoom Window”, and select 10 feet. The 20 to 30-foot portion of the water column is now displayed on the Zoom display, and the entire water column is viewable on the flasher window.
The LX-9 also features “Chart Zoom” which enables you to use a scrolling graph in Zoom mode. Activate the Chart Zoom in the Display Options of the menu. You set the zoom just as you would when using the other sonar options. When you press the ZOOM button to make a change, the Vertical Zoom window will automatically open. After adjustments have been made, you may turn the Vertical Zoom window off again in the Display Options of the menu. It is not possible to display your gauges if you only have the Chart Zoom display open.
CONE ANGLE INFO
A feature unique to the LX-9 is the “Sonar Footprint” which displays the
actual area being covered by your transducer while you are fishing. This data
is displayed below the Cone Angle Icon and represents the diameter of the base
of the transducer cone. This will keep you constantly updated on how much area
is being covered by your LX-9 and will help you decide which transducer angle
best suits the conditions. When the LX-9 is first turned on, it will be
transmitted utilizing the 20-degree setting. To switch from 20 degrees to 8
degrees, simply press the CONE ANGLE button once, and the CONE ANGLE icon will
change from 20 degrees to 8 degrees, and the Sonar Footprint will change with
it.
Conditions where the narrow beam will benefit you are:
- Fishing in deep water (over 40’) for walleyes, perch, or lake trout
- Fishing along very steep drop-offs for bottom-hugging walleyes
- Fishing in big schools of fish, like suspended crappies or tullibees
- Fishing in and around heavy weeds for panfish, like bluegills and crappies
- Fishing in a crowd, the narrow beam will reduce interference from your neighbor
INTERPRETING SIGNALS
DIGITAL DEPTH
The digital depth display on the LX-9 provides a quick and easy way to
determine depth. Digital Depth is displayed in the center of the circular
display, and on the bottom of the vertical displays. It will also show in the
upper left corner of the graph in some configurations. This display can be
used as a quick reference when setting your zoom or checking depths through
the ice.
READING BOTTOM
When interpreting your bottom signal, always read the leading edge
(shallowest side) of the signal return. If you have a strong signal return
(wideband) and it starts at 13 feet and ends at 16 feet, the correct depth is
13 feet or the shallowest leading edge of the return signal. Anything beyond
the shallowest leading edge indicates the strength of the return signal.
Your LX-9 can determine the bottom composition. The thicker and bolder your bottom shows, the harder the bottom is. In some cases, the hard bottom can be indicated by a “double” or second echo that will show on your display at approximately twice the water depth. Soft bottom (silt, mud, muck) will only register one bottom reading. Using your Sonar in conjunction with the underwater viewing system is a great way to learn how to interpret your sonar signals.
READING FISH
Fish will generally appear as separate targets from the bottom. Depending on
the size of the fish and the location within the transmit beam, fish can show
up as any of the colors in the palette you are using. Larger fish located in
the center of the beam (cone) will probably appear RED and will be displayed
as a wider band on the display. Smaller fish or fish on the outside of the
cone may appear as any of the other colors. Fish moving through the transmit
beam may change color as the return signal strengthens or weakens reflecting
their location.
Some fish, like walleyes, are notorious for cruising right on the bottom. The LX-9 has target separation fine enough that it will generally show bottom- hugging fish as a separate signal. However, fish that are right on the bottom can appear as part of the bottom. The best indication of a fish sitting right on the bottom is that the leading edge of the bottom return signal is either a dithering or flickering segment right at the bottom. If you are experiencing a lot of fish tight to the bottom, be sure to try using the “Chart Enhance” in the Scrolling Graph this helps separate signals from bottom-hugging fish from the bottom. Utilizing the ZOOM feature can give you a magnified look at the bottom when this is happening, and help you better learn what is going on below you.
Schooling fish, like crappies or tullibees, will sometimes group in large numbers suspended off the bottom. A big school of fish concentrated in one portion of the water column can show on your sonar as one large “blob”, and it can be difficult to pick out individual targets. Zooming in on the zone with the most fish will give you a better definition, and switching to the 8-degree cone will eliminate signals from fish on the periphery of your area, improving your definition even more.
READING LURES AND JIGS
The LX-9 will pick up and display the smallest of lures and jigs. When tuning
the unit to display your lure, lower the object to the desired depth and turn
up the SENSITIVITY until you see the lure on the display. It is important that
the SENSITIVITY be set so it displays the lure or bait as you raise or lower
it. Once you have the SENSITIVITY set where you want it, you can fine-tune
your signals by using the TARGET ADJUST button.
DEAD ZONE
All sonar units will have a dead zone in certain circumstances. This occurs on
sharp drop-offs where the transmit beam (cone) hits the shallower edge of the
drop-off and returns before the deeper edge returns. This in effect creates an
undisplayed area between the shallower and deeper water within the transmit
beam. The 8-degree transmit option on the LX-9 will greatly reduce this
effect.
HOW TO DECIDE WHICH CONFIGURATION TO USE
With 5 different sonar windows and a plethora of other settings [as well as
underwater viewing capabilities] it can be hard to decide on which one to
display. If you have used traditional mechanical flashers in the past, you may
like the familiarity of the LX-9’s flasher display. The flasher displayed with
one or more of the vertical displays is likely to be how most anglers use the
LX-9, at least for starters. We get endless feedback on how well the scrolling
graph display works for ice fishing, so be sure to give it a try. Be sure to
experiment with different color palettes and backgrounds, too.
CIRCULAR [FLASHER] DISPLAY
This Sonar window will read much like a traditional flasher-style display. You
can set the range manually, or allow the Auto Range or Dynamic Depth Interface
to automatically lock into a RANGE that will optimize the use of the circular
display. Signals are displayed as various colored lines on the dial, and the
different colors represent different signal strengths.
VERTICAL DISPLAYS
These Sonar Portals are very easy to interpret—the top is the top, and the
bottom is the bottom. Anything in between the top and bottom is weeds, fish,
or your lure. There are two different Vertical displays—one shows the entire
water column, and one shows your ZOOM window. On each one, signals are
displayed as various colored lines on the column, and the different colors
represent different signal strengths.
SCROLLING GRAPH (CHART) DISPLAYS
These displays will show not only what is happening below you in real-time,
but will also enable the user to have a “history” of what has happened. While
most commonly used for open water, many anglers are discovering the benefits
of using a graph on the ice. The LX-9 stands apart from other graphs in that
it displays ultra-fast “True-Time” sonar response – less than .02 seconds
between the echo reaching the transducer and when a signal appears on the LCD
screen. When used from a boat in open water, the user will see signals
displayed in classic “Graph” fashion; the bottom will be a solid band, and
fish or other objects displayed as “arches”. The “Chart Enhance” feature makes
this display that much better. When used from a stationary position, such as
ice fishing, the bottom will display as a solid band, but other signals, like
fish or your jig, will display as lines of varying thickness. A large fish is
likely to display as a fairly thick band, while a small ice jig will show as a
very fine line. The best way to learn how to interpret signals on the graph is
to have it displayed along with the circular or vertical display. After using
the graph along with one of the more familiar displays, you may find that you
like fishing with the graph best of all. It is fascinating to watch the
“trail” of your jigging motion, and fine-tuning your presentation to exactly
what the fish want has never been easier. Using any of the sonar functions in
“Heads Up” mode allows you to see real-time sonar along with real-time video-
now you can learn how to interpret those signals!
(This chart view shows a depth of 40 ft. and fish scattered throughout the water column. Note: This example is in an open water simulator mode so the fish are showing as arches.)
USING THE MANTA CAMERA
Make sure the camera cable is attached to the pigtail video plug coming out of the back of your monitor. Press the MENU button and highlight “View Mode”. Selecting “Camera”, “Heads Up”, or “Split Screen” will allow video from your Manta camera to be displayed in various configurations.
- “Camera” will display video only.
- “Heads Up” will have your sonar functions displayed on top of the video.
- “Split Screen” will put the two Vertical Sonar Displays on the edges of your display, on top of the video.
The depth of field (distance the camera can see underwater), depends on the clarity of the water and available light at the depth the camera is used. In clear water, the depth of field can be many feet but in cloudy or muddy water the depth of view can be reduced to only a few inches due to particles suspended in the water. Dirty or muddy water and/or low light penetration can detract from the quality of the color picture. Optimum color quality will result from clear water and adequate light penetration.
NOTE : The Color-kill feature will turn on automatically when the camera’s light sensor doesn’t detect enough light for optimal color viewing. This can happen in low light conditions, in deep water, or when the ice is very thick and/or covered with snow.
ON-SCREEN DISPLAY (OSD) FUNCTIONS
The Manta camera contains a digital temperature sensor, a pressure sensor for
measuring camera depth, and an electronic compass sensor used to determine the
heading of the camera. The monitor base includes an additional compass sensor
used to determine the heading of the monitor. The OSD circuit receives data
from the camera, calculates the “relative” heading of the camera, and displays
temperature, depth, voltage, and heading. The heading is displayed as an arrow
that rotates on an axis like the needle on a compass. It points in the
direction that the camera lens is facing relative to the position of the
monitor.
For this indication to be accurate, the camera must be suspended by the cable, and the monitor must be on a level surface. If either the camera or the monitor rotates, so will the arrow. An arrow pointing to the top of the monitor indicates the camera is looking straight ahead. An arrow pointing left indicates the camera is pointing to the left relative to the direction the monitor is facing. Down indicates behind, and right indicates to the right. When enabled, the temperature, voltage, and depth are also displayed along the top.
Compass Calibration:
If the direction of the Camera Compass has become inaccurate, it may be
necessary to recalibrate. First, have your monitor on a level surface like a
countertop, and have the camera hanging freely about two feet below. To re-
calibrate, go to SYSTEMS SETTINGS, and then highlight CAM COMP CAL. Select ON,
and press MENU/ENTER. Now rotate the camera two full revolutions and back
while keeping it level. Go back to CAM COMP CAL in the menu, and select OFF.
Next, go to SYSTEM SETTINGS, and then highlight LCD COMP CAL. Select ON, and
press MENU/ENTER. Slowly rotate the monitor on a level surface for two full
revolutions. Go back to LCD COMP CAL in the menu and select off. Your
directional arrow should now be accurate.
Camera Lights:
Camera lights can be turned on or off in the System Settings sub-menu.
A/V PORT
On the back of the monitor, there is a rectangular rubber cap that protects
the SD recording mechanism, the RCA video out jack, and the USB port.
Utilizing the RCA Jack:
There are many anglers with large ice fishing shacks that with a big screen TV
inside. You can easily send the video and sonar signals from your LX-9 to your
big TV by simply running an RCA cable from the LX-9 to your TV. Be sure to
select “Video Out” in the System Settings part of the menu first.
NOTE : If you have a shack that is powered by a generator, you may be interested in using the optional AC adapter available at Marcumtech.com. You can power your LX-9 [or any other Marcum unit] right off your generator with it, eliminating the need for your battery.
Ice Fishing Application
The camera of your LX-9 can be used to search for that perfect weed line or
locate the crib or rock pile where fish will generally school, entertain the
kids, or as the perfect tool to enhance your ice fishing experience. To use as
a search tool, drill a series of holes through the ice in the location you’re
interested in fishing. The LX-9 is small enough to hold in your arms while
walking from hole to hole. Drop the camera down each hole in search of the
best spot or until you locate fish. Keep your eye on the directional and depth
indicators to pinpoint the fish’s hideout.
Once you have decided on an area to fish, you will be best served to drill a separate hole for the camera cable. How far away from your angling hole this should be can depend on a few factors, like water depth, water clarity, and light penetration. Around 4 feet is a good starting point. Deploy your camera to the desired depth and lock it into place in the provided camera panner. You can now use the remote control on the panner to get the camera pointing in the right direction. Pay attention to the camera’s “heading”, indicated by the arrow that rotates around the screen. You should have a jig down your angling hole for reference.
The depth of field (distance the camera can see underwater) depends on the clarity of the water and available light at the depth the camera is used. In clear water, the depth of field can be many feet but in cloudy or muddy water the depth of view can be reduced to only a few inches due to particles suspended in the water. Dirty or muddy water and/or low light penetration can detract from the quality of the color picture. Optimum color quality will result from clear water and adequate light penetration.
Your camera also includes a down viewing/trolling fin that snaps into the back of the Manta camera. Once the fin is attached, the camera cable can be inserted through the cutout at the rear of the fin and locked into place. It is recommended that you leave about six inches of excess cable, forming a loop, before locking the cable into place. The camera can now be lowered into the hole to view what is directly below you. This can be very helpful while fishing in shallow water.
If you are going to be in a situation where underwater viewing is not practical, you can easily detach the camera and the special pouch for the camera and cable. This will make your system a little lighter.
Open Water Application
The LX-9 is just at home on a boat as it is in your ice shack. The Universal
Transducer [sold separately] is designed to be mounted right to your boat’s
transom, or to the lower unit of a bow-mounted trolling motor. This design
makes it easy for you to use your LX-9 for high-speed scouting work, or for
breaking down a piece of structure one piece at a time. The Universal
Transducer can transmit an 8 or 20-degree cone, and it also has a temperature
sensor. From an anchored or otherwise stationary position, you can use your
LX-9 from a boat much like you would on the ice—you can see the fish and how
they react to your jig on the screen.
You may also opt to use the camera functions in open water. To locate fish, look for treasure, or find that perfect spot, simply turn the camera power ON and drop the Manta camera into the water. If you’re drifting with the wind or using a trolling motor with your camera, attach the supplied down viewing/trolling fin to the rear of the Manta Camera for added stability. The internal weight is enough to keep the camera down while the fin assists in keeping the Manta camera tracking straight through the water. The direction, temp, and depth indicators combined with the solar intelligent H2D display make this is ultimate search tool. Learn in minutes what would normally take a lifetime to reveal through traditional sonar.
Moving along at speeds of 1 mph or less will give the best viewing opportunities. It is a good idea to have a GPS and/or a marker buoy at hand to quickly mark any hotspots for future reference. This is a great way to learn new ice fishing hotspots. Imagine finding a rock pile that no one else on your lake knows about! Always use extra caution when viewing around underwater obstructions, like boulders, cribs, or wrecks. If the camera becomes hung up, back up from the direction you were traveling from and slowly try to back the camera out of the snag. DO NOT pull directly upward with force unless all other avenues have been pursued.
SOFTWARE UPDATES
Your Marcum LX-9 can have the software updated. We may come out with new
software versions to add features or to improve performance. To see which
version you have, press the MENU button, then select SYSTEM SETTINGS. The
version will be displayed at the top of the menu window as a number with a “v”
in front of it.
To see if there are new versions available, check our website or stay in touch through various social media outlets. Compare the software version on your system with what we have available online, and ensure your system has the highest-numbered version. New software updates and instructions can be by following the below link: http://marcumtech.com/~marcum/lx-9-firmware
BATTERY CHARGER TROUBLESHOOTING
A majority of inquiries that come to our office are battery or battery
charger-related. Battery failure can be caused by a fault in the charging
system, and many times the issue is with the fuse on the wiring harness. If
you suspect your battery is not being charged, follow these troubleshooting
tips:
- When the charger is plugged into the WALL ONLY it should show a green light. If there is no light showing, confirm that the outlet is good. If the outlet is good, the charger itself is likely faulty.
- If the charger is plugged into the BATTERY ONLY it should show a green light. If it does not show a green light, likely, that the charger is not making contact with the battery. The most likely reason for this is a faulty fuse on the wiring harness. This fuse is a 2-amp automotive fuse, and it should be replaced with a 2 or 3-amp fuse available anywhere that sells auto parts. The fuse can blow out if there is a short in the charging system, or if the plug end of the wiring harness comes in contact with a battery terminal.
- When the charger is plugged into both the wall and the battery, there should be a red light showing on the charger. A red light showing indicates that the charger is in contact with the battery and is actively charging the battery. Once the battery has reached a voltage level that is considered “fully charged” the red light should change to green. If after 24 hours the light has not changed to green there is no cause for alarm! Remember that when the light is red, the battery is being charged, and you will be able to use your system.
- If it has been over 24 hours and the light is not green, the first thing you should do is unplug the charger and turn on your LX-9. The LX-9 has a built-in voltmeter; it shows as one of the gauges. How different batteries will react with a charger isn’t 100% possible to predict, but after 24 hours your battery should be charged to around 13 volts. If your unit turns on and has a voltage level over 12 volts, there is no need for concern, you should go fishing! If it is not at or above 12 volts after charging you should consider replacing the battery.
- If the charger is plugged into the wall and battery, and you get a blinking light on the charger, it is very likely that the battery is faulty and should be replaced.
TWO YEAR WARRANTY
Marcum warrants this product to be free from defects in materials and
workmanship for two years from the date of purchase. This warranty applies to
customers who properly complete the online product registration form found on
the MarCum Technologies Website http://marcumtech.com/support/
If you are unable to use the internet, please fill out and submit the enclosed warranty registration card to be eligible for the two-year warranty. Marcum Technologies will repair or replace any components that fail in normal use. Failures due to abuse, misuse, unauthorized alteration, modification, or repair are not covered. The battery is not covered by the warranty. The warranty is valid only for the original owner who purchases the unit from an authorized dealer. An original sales receipt dated within the warranty period is required for all warranty claims.
HOW TO OBTAIN SERVICE
If your unit is malfunctioning, check the FAQ section of our website. You may
find that the solution to your problem is something you can resolve yourself.
If you need to send it in, there is no need to contact our office. Getting
repairs made is as simple as going to our website, clicking on the service
tab, and then filling out the Service Request Form. If your unit is under
warranty, be sure to attach a picture/scan of your receipt showing the date of
purchase. If your system is out of warranty, we have several flat-rate fees
that will cover the cost of repairs, including parts and labor. Once you have
completed the Warranty or flat rate repair, package the unit as described on
the website and ship it to us.
There is no need for an authorization or reference number, just make sure that you have included your contact info and a brief description of the issue on a note in the box. If you cannot use the Internet, you may also fill out the service request form included in the box with your unit. If you enclose this form in the box with your unit there is no need to contact our office, just include the filled-out form in the shipping box.
Some people are more comfortable calling for shipping instructions. During peak ice season, we sometimes receive a high volume of calls, making it impossible to get to all customers who phone in. For this reason, strongly consider using the online form or email rather than calling. In your email, please provide your name, complete address, and cell phone #. Please indicate what model Marcum you have, the approximate date of purchase, and what has gone wrong with it.
Please send your email inquiries to service@versae.com If you are unable to use email or the internet, you may also call us at 763-512-3987. Our office hours are Monday – Friday, 8 – 4 Central Time. International callers may use 888-778-1208.
OUR ADDRESS: MARCUM TECHNOLOGIES ATTN: SERVICE DEPT. 3943 QUEBEC AVE NORTH MINNEAPOLIS, MN 55427
The customer is responsible for shipping costs associated with returning the unit to Marcum Technologies. Marcum will pay for shipping the repaired unit back to the customer while it is still under warranty. All out-of-warranty services will be charged a fee for service and shipping which must be paid in advance. The unit should be securely packed and shipped “pre-paid freight” and insured to Marcum Technologies. It is the customer’s full responsibility to track the products sent out in the mail or other forms of delivery service. Marcum Technologies will not be liable for packages lost en route to us. Unless specified otherwise, do not include batteries or other accessories when returning the product for repair. Marcum Technologies will not be responsible for lost or damaged accessories. Turnaround time can vary, on average it is about 1 week.
ACCESSORIES
-
Soft pack
This is the red pack that protects your Digital Sonar from the elements. -
Shuttle
The plastic base with a handle that your Digital Sonar is mounted to. -
Ducer Arm
Positions your ducer cable. Having an extra one on hand is not a bad idea; clumsy friends have been known to break these. -
Ice Ducer
If you have lost or damaged your ducer you can buy one from us or premium retailers. If you think your ducer quit working, you should contact customer service before buying a new one. -
Stopper
This suspends your ice dancer in the hole along with the dancer’s arm. -
12 volt Battery
Batteries don’t last forever, buying an extra one is cheap insurance that you will always be able to use your Digital Sonar -
Power Cord
This connects your monitor to the battery -
Charging System
This includes a charger and a fused wiring harness -
Snow shield
Protect your Digital Sonar from rain and snow with this clear snow shield -
Open Water Ducer
Use your Digital Sonar all year! This reducer mounts on the transom or trolling motor.
www.marcumtech.com MarCum Technologies 3943 Quebec Ave North Minneapolis, MN 55427 763-512-3987 International: 1-888-778-1208
FAQ’s
Can I use the LX-9 for both sonar and video fishing?
Yes, the LX-9 offers both sonar and video features, allowing you to utilize both functionalities.
How long is the warranty for the LX-9?
The LX-9 comes with a 2-year warranty.
Can I adjust the zoom on the LX-9?
Yes, the LX-9 has an adjustable zoom feature that allows you to focus on specific areas.
References
- MarCum® Ice Fishing Sonar & Underwater Cameras
- MarCum® Ice Fishing Sonar & Underwater Cameras
- Support - Marcum Tech
- MarCum® Ice Fishing Sonar & Underwater Cameras
- MarCum® Ice Fishing Sonar & Underwater Cameras
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>