Middle Atlantic Products Proximity Series Sliding Mounting Plate Instructions

Middle Atlantic Products Proximity Series Sliding Mounting Plate

Product Information

Specifications:

• Model : PRX-SMP-15X10
• Weight Rating : 15 lbs. Maximum Total Rated Load

Product Features:
The Proximity Series Sliding Mounting Plate offers the following features:

• Designed for easy installation and assembly
• Can be mounted directly on the wall or on the front/back of an extrusion
• Includes Lever LockTM for secure mounting

Important Safety Instructions:
WARNING: Failure to read, understand, and follow the following information can result in serious personal injury, damage to the equipment, or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to specifications.

• Weight Ratings:
  This product is intended for use only with the products and maximum weights indicated. Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury. Total equipment weight must not exceed 15 lbs. (6.80 kg).

• Supplied Components:
  The Proximity Series Sliding Mounting Plate comes with the following components:

  • Sliding Mounting Plate A
  • Lever LockTM B
  • (2x) Rivet C
  • (2x) Washer D
  • (4x) Binding Head Screw E
  • (4x) Square Nut F
  • (4x) Pan Head Screw G
  • (4x) Drywall Anchor H
  • (20x) Washer J

Product Usage Instructions

Installing the Sliding Mounting Plate to the Wall:

1. Using (4x) pan head screws (G) and (4x) drywall anchors (H) provided, mount the sliding plate to the wall. Ensure that only drywall anchors (H) are used for mounting to 3/8 minimum to 5/8 maximum thick drywall. (Refer to Figure A on page 4)
2. For horizontal wall mount – right, mount the Lever LockTM with the clip at the bottom. For horizontal wall mount – left, refer to Figure A on page 4.

Installing the Sliding Mounting Plate to the Front of an Extrusion:

1. Remove screws and endcap to access binding head screws (E) and square nuts (F).
2. Pre-load (4x) binding head screws (E) and (4x) square nuts (F) loosely prior to mounting the sliding plate to provide clearance for mounting. (Refer to Figure B on page 4)
3. Mount the sliding plate (A) over screws (E) by utilizing keyholes in the plate. Lower the sliding plate until it rests on the screws. (Refer to Figure C on page 4)
4. Tighten screws securely against the plate.
5. Note: Use a minimum of 2 pairs of mounting keyholes to safely mount the sliding plate to the extrusion as far apart as possible.
6. The sliding mounting plate can be placed at either the extreme right end or the extreme left end of the extrusion. (Refer to Figure D on page 6)

Installing the Sliding Mounting Plate to the Back of an Extrusion:

1. Remove screws and endcap to access binding head screws (E) and square nuts (F).
2. Pre-load (2x) binding head screws (E), (2x) washers (D), and (2x) square nuts (F) loosely prior to mounting the sliding plate.
3. Follow the same steps as mentioned in the previous section for mounting the sliding plate to the front of an extrusion.

FAQ

1. Q: What is the weight rating for the Proximity Series Sliding Mounting Plate?
   A: The weight rating for this product is 15 lbs. Maximum Total Rated Load.

2. Q: Can I use this product with other products or products heavier than the maximum weights indicated?
   A: No, this product is intended for use only with the products and maximum weights indicated. Using it with other products or heavier weights may result in instability and possible injury.

3. Q: How should I mount the Lever LockTM for horizontal wall mount?
   A: For horizontal wall mount – right, mount the Lever LockTM with the clip at the bottom. For horizontal wall mount – left, please refer to Figure A on page 4 for detailed instructions.

4. Q: Can I mount the sliding mounting plate to both the front and back of an extrusion?
   A: Yes, you can mount the sliding mounting plate to both the front and back of an extrusion. Please refer to the respective sections in the user manual for detailed instructions.

Instruction Sheet
Proximity Series Sliding Mounting Plate

THANK YOU
Thank you for purchasing the Proximity Series Sliding Mounting Plate. Please read these instructions thoroughly before installing or assembling this product.

PRODUCT FEATURES

The Sliding Mounting Plate (PRX-SMP-15X10) provides mounting of AV components and power that can be conveniently hidden behind a wall-mounted display.

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with dry cloth.

• Only use attachments/accessories specified by the manufacturer.

• WARNING: A warning alerts you to a situation that could result in serious personal injury or death.

• WARNING: Middle Atlantic Products, Inc. electrical systems conform to and should be properly grounded in compliance with requirements of the current National Electrical Code or codes administered by local authorities.
  All electrical products may present a possible shock or fire hazard if improperly installed or used. Middle Atlantic Products, Inc. electrical products may bear the mark of a Nationally Recognized Testing Laboratory (NRTL) and should be installed in conformance with current local and/or the National Electrical Code.

• WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to specifications.

WEIGHT RATINGS

WARNING: This product is intended for use only with the products and maximum weights indicated. Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury. Total equipment weight must not exceed 15 lbs. (6.80 kg).

SUPPLIED COMPONENTS

INSTALLING THE SLIDING MOUNTING PLATE TO THE WALL

NOTE: Sliding mounting plate (A) may be installed directly on the wall in 2 horizontal positions as shown.

1. Using (4x) pan head screws (G) and (4x) drywall anchors (H) provided, mount the sliding plate to the wall as shown. (FIGURE A)
   • CAUTION: Only drywall anchors (H) are to be used for mounting to 3/8 minimum to 5/8 maximum thick drywall.
   • CAUTION: Lever Lock must be mounted with the clip at the bottom.

INSTALLING THE SLIDING MOUNTING PLATE TO THE FRONT OF AN EXTRUSION

1. Remove screws and endcap to access binding head screws (E) and square nuts (F).
2. Pre-load (4x) binding head screws (E) and (4x) square nuts (F) loose prior to mounting the sliding plate providing clearance for mounting. (FIGURE B)
3. Mount sliding plate (A) over screws (E) utilizing keyholes in plate by lowering sliding plate until it rests on screws. (FIGURE C)
4. Tighten screws securely against plate.
   NOTE: At a minimum use 2 pairs of mounting keyholes to safely mount the sliding plate to the extrusion as far apart as possible.
   NOTE: Sliding mounting plate can be place to either the extreme right end of the extrusion, or the extreme left end of the extrusion. (FIGURE D)
   CAUTION: Lever Lock must be mounted with the clip at the bottom.

INSTALLING THE SLIDING MOUNTING PLATE TO THE BACK OF AN EXTRUSION

1. Remove screws and endcap to access binding head screws (E) and square nuts (F).
2. Pre-load (2x) binding head screws (E), (2x) washers (D) and (2x) square nuts (F) loose prior to mounting the sliding plate providing clearance for mounting. (FIGURE E)
3. Mount sliding plate (A) over screws (E) utilizing keyholes in plate by lowering sliding plate until it rests on screws. (FIGURE F)
4. Tighten screws/washers securely against plate.
   NOTE: At a minimum use 2 mounting keyholes to safely mount the sliding plate to the extrusion as far apart as possible.
   NOTE: Sliding mounting plate can be place to either the extreme right end of the extrusion, or the extreme left end of the extrusion. (FIGURE G)
   CAUTION: Lever Lock must be mounted with the clip at the bottom.

INSTALLING THE LEVER LOCK PANEL TO THE SLIDING MOUNTING PLATE

1. Attach the Lever Lock plate (B) by installing the side without the clip into the bracket first.
2. Install the side with the clip until it clicks into place. (FIGURE H)

CLEARANCE HEIGHTS

1. Method 1 – Attach the sliding mounting plate (A) directly to the wall. (FIGURE J)
2. Method 2 – Attach the sliding mounting plate (A) to the back of the extrusion. (FIGURE K)
3. Method 3 – Attach the sliding mounting plate (A) to the front of the extrusion. (FIGURE L)

WARRANTY

• For warranty information, refer to http://www.middleatlantic.com/company/about-us.aspx#warranty
• Corporate Headquarters
  • Corporate Voice: 973-839-1011
  • Fax: 973-839-1976 / International Voice: +1 973-839-8821 –
  • Fax: +1 973-839-4982
  • www.middleatlantic.com – info@middleatlantic.com
• Middle Atlantic Canada
  • Voice: 613-836-2501 –
  • Fax: 613-836-2690 / ca.middleatlantic.com –
  • customerservicecanada@middleatlantic.ca
• Factory Distribution
  • USA: NJ – CA – IL Canada: ON – BC
  • At Middle Atlantic Products we are always listening. Your comments are welcome.
  • Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
• Middle Atlantic Products what great systems are built on middleatlantic.com
• 800.266.7225

References

• About Us | Legrand AV
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>