SereneLife SLPORBT36 Automatic Robotic Pool Cleaner User Guide
- June 4, 2024
- serenelife
Table of Contents
SIPORBT36
Automatic Robotic Pool Cleaner
Pool Cleaning Robot with Three Motors, Wall Climbing, Easy to Clean Up to
50 ft.
USER GUIDE
SLPORBT36 Automatic Robotic Pool Cleaner
Please read this User Manual in its entirety to ensure proper operation and
care of your SLPORBT36 Automatic Robotic Pool Cleaner.
IMPORTANT: PLEASE READ BEFORE OPERATING THE CLEANER
Product Introduction
Human beings have liberated their hands because they walked upright.
Even in modern society with advanced technology, liberated hands are still the
unremitting pursuit of human beings. The SereneLife Automatic Robotic Pool
Cleaner is developed for this purpose. The Robotic Pool Cleaner is a kind of
underwater cleaner, it is fully automatic. It is mainly used to clean the dirt
and debris such as hair, leaves, and sand from the pool floor; pool wall, and
waterline. As long as you put it into the pool after the initial program
setting, the Robotic Pool Cleaner can automatically measure the size of the
pool, automatically design the working route, and clean the pool by itself.
WARNING AND CAUTIONS
WARNING: Do not operate the robotic pool cleaner when there are people
swimming in the pool. Communication cables can trip or entangle swimmers which
could result in drowning.
WARNING: Keep the robotic pool cleaner out of reach of children. Keep the
robotic pool cleaner out of reach of persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, without proper
supervision and understanding of the instructions.
WARNING: DO NOT switch on the pool cleaner if it is not immersed in the
water.
Operating the cleaner out of the water may cause severe damage and will result
in a loss of warranty.
WARNING: Shut off and unplug the power supply every time you remove the
cleaner from the water.
WARNING: DO NOT PULL THE POOL CLEANER FROM THE POOL USING THE CABLE, USE
THE HANDLE.
WARNING: Only use this cleaner when the water temperature is 10-35°C or
50-95°F and the pool depth is 0.5m-3m. The cleaner is designed for a 100m²
surface area.
WARNING: Keep the controller box in a dry place that is out of direct
sunlight and is 3.5m away from your pool.
GETTING STARTED
- ****: Turn power supply ON/OFF, error alarm.
- FLOOR CLEAN ONLY: To clean the pool floor only. It will increase the cleaning efficiency
- ALL PURPOSE CLEAN: All-around cleaning, including pool floor, pool wall, and waterline.
- RUNNING TIME (set the cleaning time): Set the preferred running hours (2/3/5 hours, press the button to set the cleaning time, red light means the cleaner will work for 2 hours, green light for 3 hours, and blue for 5 hours), before you start the cleaning. The cleaner will stop automatically after working.
OPERATION INSTRUCTIONS
- Place the power supply (transformer) at least 3.5 meters/11.5 feet from the pool and at least 12 cm/4 Inch above the surface. The transformer will supply low voltage to the cleaner.
- Connect the floating power cord.
- Place the unit in the water. Release the Pool Cleaner and let it sink to the floor of the pool. Make sure that the floating cable is free of any obstructions.
- Start: Turn the power supply ON (115V AC 60HZ). One of the three modes of light will be on. Press the ****button for the mode and time you want to run, then press the button and the Pool Cleaner will now operate.
- Mode switching: Press the button, choose the mode, and press the button to start the cleaner.
- Indicator Lights:
LED Light| Status| Indication
---|---|---
White| On| Robotic Pool Cleaner Normal operation
White| Blinking twice| Work reversely after meeting obstacles
White| Always blinking| Wireless BT communication with the pool cleaner or standby status
Red| On| Overload or No-load protection
Let the cleaner sink to the floor of the pool, and press on/off to start again.
ROUTINE MAINTENANCE
-
Clean the Filter Basket
Cut off the power supply (light goes out) Turn off the Pool cleaner.
Open the filter cover. Clean the filter basket with a hose. Insert the clean filter basket and close the filter cover.
Make sure the
power supply is switched OFF and unplugged.
It is highly recommended to clean the filter basket after each cleaning cycle. -
Use of filter paper core
The filter paper core is a fragile part, which can filter particles below 100µm, and its service life is less than 72 hours. (The filter paper core can be used without affecting the performance of the robot, and it is strongly recommended that the filter paper core be not used in the dirty swimming pool.) -
Floating Cable Routine Maintenance
The floating cable may get intertwined after 8 hours of working which needs to be sorted out manually. It highly recommends sorting the cable out after each cleaning.
TROUBLESHOOTING
| Symptom | Possible Reason | Solution |
|---|
The pool cleaner moves but does not clean the
pool| Clogged filter basket| Clean the filter basket
The pool cleaner does not move| • The impeller gets blocked.
• The drive belt gets blocked| Unplug the power supply. Open the impeller
cover and check that nothing is trapped in the impeller.
Verify that nothing blocks the tracks or wheels.
Debris out from the outlet| • Filter basket is broken
• Filter basket is full| • Replace the filter basket
• Clean the filter basket
Intertwined oating cable| Long working hours, over8 hours.| Untwist the
heating cable before re-start.
Stop Working| Overload or no-load protection| Let the cleaner sink to the door
of the pool, and press to start again.
California Prop 65 Warning!
WARNING:
This product contains Phthalates which are known to the state of California to
cause cancer birth defects and other reproductive harm. Do not ingest.
For more info go to:
www.P65warnings.ca.gov
SPECIFICATIONS
Features:
- Design to Clean the Pool Effortlessly
- With Dual Scrubbing Brushes and Superior Filtering Capabilities
- Saves Energy
- Traps and Locks-in All Sorts of Dirt and Debris
- Tangle-Free Cable
- Easy to Use
- Ideal for In-ground Swimming Pools Up to 50 Feet
- Fully Automatic Robot Cleaner
What’s in the Box:
- Cleaner
- Control box
- Floating Cable
Technical Specs:
- Construction Materials: ASA
- Cleaning Area: Up To 50 Square Foot
- Cleaning Coverage: Floor wall & Waterline
- Filtration Accuracy: ≥100µm
- Length of Floating Cable: 55.8 ft.
- Filter Speed: 14-18 m3/h
- Filter Type: Twin Cartridges
- Output Voltage: 24V DC
- Output Current: 4.5A
- Input Voltage: 115V
- Frequency Response: 60Hz
- Horsepower: 150W
- IP Class for Controller Box: IP54
- IP Class for Motor: IP68
- Product Dimensions: 18.5’’ x 16.1’’ x 10.04’’ -inches
Parts Breakdown and Replaceable Parts List
1. Controller box
2. Power cord for the controller box
3. Wheel brush
4. Main body
5. Drive wheel
6. Drive wheel fixing block
7. Side panel| 8. Drive belt
9. Driven wheel
10. Sleeve
11. Wheel brush
12. Filter basket
13. Floating cable
14. Filter paper core
---|---
www.SereneLifeHome.com
Questions? Comments?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
Documents / Resources
|
SereneLife SLPORBT36 Automatic Robotic Pool
Cleaner
[pdf] User Guide
SLPORBT36, Automatic Robotic Pool Cleaner, SLPORBT36 Automatic Robotic Pool
Cleaner, Robotic Pool Cleaner, Pool Cleaner, Cleaner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>