WILLIAMS SOUND ANT034 Remote Rubber Duckie Antenna User Guide

WILLIAMS SOUND ANT034 Remote Rubber Duckie Antenna

Product Information

Specifications

• Model: ANT 034
• Type: Remote Rubber Duckie Antenna
• Impedance: 75 Ohm
• Frequency Range: 72-76 MHz
• Designed for use with Williams Sound FM transmitters (PPA T35, PPA T27)

Contents

• 1 x ANT 021 Rubber Duckie Antenna with Swivel F-Connector
• 1 x CNR 004 RF Connector with nut
• 1 x WCA 086 Coax Cable, 3′, with F-Connector
• 2 x Nylon Washers
• 1 x Manual

Recycling Instructions

To protect the environment, please do not dispose of your Williams Sound equipment in the household trash. Instead, take the equipment to an electronics recycling center or return the product to the factory for proper disposal.

Assembly & Installation Procedure

1. The ANT 034 can be mounted to an audio rack using the RPK 005 (a 1/2-width, single-space rack bracket, ordered separately). This is recommended when the transmitter will also be mounted in the rack.
2. Thread the ANT 021 rubber duckie antenna onto the ANT 035 right angle F-connector. Turn the F-connector on the ANT 021 clockwise by hand until it is tightly connected.
3. Install the washers with the smaller side facing the RPK 005 rack bracket as shown in Figure 1. Ensure correct orientation of  the washers for antenna isolation. Tighten the nut with moderate pressure using the appropriate size wrench.
4. Thread one end of the WCA 086 3′ coax cable onto the back of the assembled bracket-antenna unit. Use fingers only to tighten.
5. Attach the other end of the WCA 086 3′ coax cable to the F-Connector Antenna jack on the Williams Sound 72-76 MHz transmitter (PPA T35, T27). Use fingers only to tighten.
6. Note: Do not bend the coax cable sharply at any point. The ANT 034 rubber duckie antenna should be kept vertical for optimal performance and to comply with FCC rules.

Warranty

The ANT 034 rack mountable remote antenna is covered by a 90-day warranty. If you experience any difficulties with your antenna, please call toll-free customer assistance at 1-800-843-3544 (U.S.A.) or 1-952-943-2252 (Outside the U.S.A.). If it is necessary to return the system for service, your customer service representative will provide you with a Return Authorization Number (RA) and shipping instructions.

FAQ

Q: Can the ANT 034 be used with any FM transmitter?

A: The ANT 034 is designed specifically for use with Williams Sound FM transmitters, such as PPA T35 and PPA T27. It is recommended to use it with these models for optimal compatibility and performance.

Q: What should I do if I need to dispose of my Williams Sound equipment?

A: Please do not dispose of your Williams Sound equipment in the household trash. Instead, take it to an electronics recycling center or return it to the factory for proper disposal.

Model ANT 034

Remote rubber duckie antenna for RPK-005 mounting

Overview

The ANT 034 is a 75 Ohm rack mountable remote antenna designed for 72-76 MHz operation. It is intended for use with Williams Sound FM transmitters (i.e. PPA T35, PPA T27).

Contents

• 1 – ANT 021 Rubber Duckie Antenna with Swivel F-Connector
• 1 – CNR 004 RF Connector with nut
• 1 – WCA 086 Coax Cable, 3’, F-Connector
• 2 – Nylon Washers
• 1 – Manual

Recycling Instructions

Help Williams Sound protect the environment! Please take the time to dispose of your equipment properly.

Product Recycling
Please do NOT dispose of your Williams Sound equipment in the household trash. Please take the equipment to an electronics recycling center; OR return the product to the factory for proper disposal.

Figure 1: ANT 034 Assembly

ANT 034 Assembly & Installation Procedure

1. The ANT 034 can be mounted to an audio rack with the RPK 005 (a 1/2-width, single-space rack bracket, ordered separately). This solution is most commonly used when the transmitter will also be mounted in the rack.
2. Thread the ANT 021 rubber duckie on to the ANT 035 (see figure 1). Turn the F- connector on the ANT 021 clockwise by hand until connection is tight.
3. Install the washers with the smaller side facing the RPK 005 rack bracket as shown. Correct orientation of the washers is crucial to maintaining antenna isolation. Tighten the nut with moderate pressure using the proper size wrench.
4. Thread one end of the WCA 086 3’ coax cable on to the back of the assembled bracket-antenna unit. Use fingers only to tighten.
5. Attach other end of WCA 086 3’ coax cable to the F-Connector “Antenna” jack on the Williams Sound 72-76 MHz transmitter (i.e. PPA T35, T27). Use fingers only to tighten.
   NOTE: Do not bend coax cable sharply at any point. The ANT 034 rubber duckie antenna should be vertical for best performance, and to comply with FCC rules.

Warranty

The ANT 034 rack mountable remote antenna is covered by a 90 day warranty. If you experience difficulty with your antenna, call toll-free for customer assistance:
1-800-843-3544 (U.S.A.) or 1-952-943-2252 (Outside the U.S.A.)
If it is necessary to return the system for service, your customer service representative will give you a Return Authorization Number (RA) and shipping instructions.

10300 Valley View Rd • Eden Prairie, MN 55344 800-328-6190 / 952-943-2252 • FAX: 952-943-2174 www.williamssound.com

References

• Manual-Hub.com - Free PDF manuals!
• Personal Hearing Products - Williams AV
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>