TEKNIX 90CM Range Cooker Single Cavity User Manual

90CM RANGE COOKER
SINGLE CAVITY

MODEL CODE
TKGF91SS
USER MANUAL
V1.0

GENERAL SAFETY INSTRUCTIONS

1. Installation and repair should always be performed by “AUTHORIZED SERVICE”. Manufacturer shall not be held responsible for operations performed by unauthorized persons.

2. Please read operating instructions carefully to ensure you can use the appliance safely and in the correct manner.

3. The oven should be used according to operating instructions.

4. Keep children below the age of 8 and pets away when operating.

5. WARNING: The accessible parts may be hot while using the grill. Keep away from children.

6. WARNING: Fire hazard; do not store the materials on the cooking surface.

7. WARNING: The appliance and its accessible parts are hot during operation.

8. Setting conditions of this device are specified on the label. (Or on the data plate)

9. The accessible parts may be hot when the grill is used. Small children should be kept away.

10. WARNING: This appliance is intended for cooking.
    It should not be used for other purposes like heating a room.

11. To clean the appliance, do not use steam cleaners.

12. Ensure that the oven door is completely closed after putting food inside the oven.

13. NEVER try to put out the fire with water. Shut down the device circuit and then cover the flame with a cover or a fire blanket.

14.  Children under 8 years of age should be kept away, if they cannot be monitored continuously.

15. Touching the heating elements should be avoided.

16. CAUTION: Cooking process should always be supervised.

17. This device can be used by children over 8 years of age, people with physical, hearing or mental challenges or people with lack of experience or knowledge; as long as control is ensured or information is provided regarding the  dangers.

18. This device has been designed for household use only.

19. Children must not play with the appliance. Cleaning or user maintenance of the appliance shall not be performed by children unless they are older than 8 years and supervised by adults.

20. Keep the appliance and its power cord away from children less than 8 years old.

21. Put curtains, tulles, paper or any flammable (ignitable) material away from the appliance before starting to use the appliance. Do not put ignitable or flammable materials on or in the appliance.

22. Keep the ventilation channels open.

23. The appliance is not suitable for use with an external timer or a separate remote control system.

24. Do not heat closed cans and glass jars. The pressure may cause jars to explode.

25. Oven handle is not a towel drier. Do not hang towels, etc. on the oven handle.

26. Do not place the oven trays, plates or aluminium foils directly on the oven base. The accumulated heat may damage the base of the oven.

27. While placing food to or removing food from the oven, etc., always use heat resistant oven gloves.

28. Do not use the product in states like medicated and/or under influence of alcohol which may affect your ability of judgement.

29. Be careful when using alcohol in your foods.
    Alcohol will evaporate at high temperatures and may catch fire or cause a fire if it comes in contact with hot surfaces.

30. After each use, check if the unit is turned off.

31. If the appliance is faulty or has a visible damage, do not operate the appliance.

32. Do not touch the plug with wet hands. Do not pull the cord to plug off, always hold the plug.

33. Do not use the appliance if its front door glass removed or broken.

34. Place the baking paper together with the food into a pre-heated oven by putting it inside a cooker or on an oven accessory (tray, wire grill etc.).

35. Do not put objects that children may reach on the appliance.

36. It is important to place the wire grill and tray properly on the wire racks and/or correctly place the tray on the rack. Place the grill or tray between two rails and make sure it is balanced before putting food on it.

37. Against the risk of touching the oven heater elements, remove excess parts of the baking paper that hang over from the accessory or container.

38. Never use it at higher oven temperatures than the maximum usage temperature indicated on your baking paper. Do not place the baking paper on the base of the oven.

39. When the door is open, do not place any heavy object on the door or allow children to sit on it. Youmay cause the oven to overturn or the door hingesto be damaged.

40. The packaging materials are dangerous for children. Keep packaging materials away from the reach of children.

41. Do not use abrasive cleaners or sharp metal scrapers to clean the glass as the scratches that may occur on the surface of the door glass may cause the glass to break.

42. Do not place the appliance on a surface covered with carpets. Electric parts gets overheated since there will be no ventilation from below. This will cause failure of the appliance.

43. Do not hit glass surfaces of vitro-ceramic cookers with a hard metal, resistance can get damaged. It may cause an electric shock.

44. The user should not handle the oven by themselves.

45. The user shall be careful when cleaning gas burners. It may cause personal injuries.

46. Food can spill when foot of oven is dismantled or gets broken, be careful. It may cause personal injuries.

47. During usage, the internal and external surfaces of the oven get hot. As you open the oven door, step back to avoid the hot vapour coming out from the interior. There is risk of burning.

48. Upper cover of the oven can be closed for a reason,than cookware can trip over. Step back to avoid thehot food coming on you. There is risk of burning.

49. Do not place heavy objects when oven door is open, risk of toppling.

50. User should not dislocate the resistance during cleaning. It may cause an electric shock.

51. Do not remove ignition switches from the appliance. Otherwise, live electric cables can be accessed. It may cause an electric shock.

52. Oven supply can be disconnected during any construction work at home. After completing the work,re-connecting the oven shall be done by authorized service.

53. Do not place metal utensils such as knife, fork, spoon on the surface of the appliance, since they will get hot.

54. To prevent overheating, the appliance should not be installed behind of a decorative cover.

55. Turn off the appliance before removing the safeguards. After cleaning, install the safeguards according to instructions.

56. Cable fixing point shall be protected.

57. WARNING: Don’t use oven and grill burners at same time.

58. Please don’t cook the food directly on the tray /grid. Please put the food into or on appropriate tools before putting them in the oven.

59. Hot surface, leave for cooling before closing the cover.

ELECTRICAL SAFETY

1. Plug the appliance in a grounded socket protected by a fuse conforming to the values specified in the technical specifications chart.

2. Have an authorized electrician set grounding equipment. Our company shall not be responsible for the damages that shall be incurred due to using the product without grounding according to local regulations.

3. The circuit breaker switches of the oven shall be placed so that end user can reach them when the oven is installed.

4. The power supply cord (the cord with plug) shall not contact the hot parts of the appliance.

5. If the power supply cord (the cord with plug) is damaged, this cord shall be replaced by the manufacturer or its service agent or an equally qualified personnel to prevent a hazardous situation.

6. Never wash the product by spraying or pouring water on it! There is a risk of electrocution.

7. WARNING: To avoid electric shock, ensure that the device circuit is open before changing the lamp.

8. WARNING: Cut off all supply circuit connections before accessing the terminals.

9. WARNING: If the surface is cracked, turn off the appliance to avoid risk of electric shock.

10. Do not use cut or damaged cords or extension chords other than the original chord.

11. Make sure that there is no liquid or humidity in the outlet where the product plug is installed.

12. The rear surface of the oven also heats up when the oven is operated. Electrical connections shall not touch the rear surface, otherwise the connections may be damaged.

13. Do not tighten the connecting cables to the oven door and do not run them over hot surfaces. If the cord melts, this may cause the oven to short circuit and even a fire.

14. Unplug the unit during installation, maintenance, cleaning and repair.

15. If the power supply cable is damaged, it must be replaced by its manufacturer or authorized technical service or any other personnel qualified at the same level, in order to avoid any dangerous situation.

16. Make sure the plug is inserted firmly into wall socket to avoid sparks.

17. Do not use steam cleaners for cleaning the appliance, otherwise electric shock may occur.

18. An omnipolar switch capable to disconnect power supply is required for installation.
    Disconnection from power supply shall be provided with a switch or an integrated fuse installed on fixed power supply according to building code.

19. Appliance is equipped with a type ‘’Y’’ cord cable.

20. Fixed connections shall be connected to a power supply enabling omnipolar disconnection. For appliances with over voltage category below III, disconnection device shall be connected to fixed power supply according to wiringcode.

INTENDED USE

1. This product is designed for home use.
   Commercial use of the appliance is not permitted.

2. This appliance may only be used for cooking purposes. It shall not be used for other purposes like heating a room.

3. This appliance shall not be used to heat plates under the grill, drying clothes or towels by hanging them on the handle or for heating purposes.

4. The manufacturer assumes no responsibility for any damage due to misuse or mishandling.

5. Oven part of the unit may be used for thawing, roasting, frying and grilling food.

6. Operational life of the product you have purchased is 10 years. This is the period for which the spare parts required for the operation of this product as defined is provided by the manufacturer.

GAS CONNECTION

WARNING: Before starting any work related with gas installation, turn off gas supply. Risk of explosion. Please operate your oven in dry atmosphere.

1. Fit the clamp to the hose. Push one of the hose until it goes to the end of the pipe.
2. For the sealing control; ensure that the buttons in the control panel are closed, but the gas cylinder is open. Apply some soap bubbles to the connection. If there is gas leakage, there will be foaming in the soaped area.
3. The oven should be using a well ventilation place and should be Installed on flat ground.
4. Re-inspect the gas connection.
5. When placing your oven to its location, ensure that it is at the counter level. Bring it to the counter level by adjusting the feet if necessary.
6. Do not make gas hose and electrical cable of your oven go through the heated areas, especially through the rear side of the oven. Do not move gas connected oven. Since the forcing shall loosen the hose, gas leakage may occur.
7. Please use flexible hose for gas connection.

FOR LPG GAS CONNECTION
For LPG (cylinder) connection, affix metal clamp on the hose coming from LPG cylinder. Affix an edge of the hose on hose inlet connector behind the appliance by pushing to end through heating the hose in boiled water. Afterward, bring  the clamp towards end section of the hose and tighten it with screwdriver. The gasket and hose inlet connector required for connection is as the picture shown below.
NOTE: The regulator to be affixed on LPG cylinder should have 300mmSS feature.

FOR NATURAL GAS CONNECTION
WARNING: Natural gas connection should be done by an authorized service person. For natural gas connection, place gasket in the nut at the edge of natural gas connection hose. To install the hose on main gas pipe, turn the nut.  Complete the connection by making gas leakage control. For natural gas connection;

GAS HOSE PASSAGEWAY
Connect the appliance to the gas piping tap in shortest possible route and in a way that ensure no gas leakage will occur.
In order to carry on a tightness and sealing safety check ensure that the knobs on the control panel are closed and the gas cylinder is open.
WARNING: While performing a gas leakage check, never use any kind of lighter, match, cigarette or similar burning substance.
Apply soap bubble on the connection points. If there is any kind of leakage then it will cause bubbling. While inserting the appliance in place ensure that it is on the same level with the worktop. If required adjust the legs in order the make level with the worktop. Use the appliance on a level surface and in a well ventilated environment.
WARNING: Before placing the appliance, check that the local distribution conditions (gas type and pressure) conform to the product settings.

NOZZLE CHANGE OPERATION

1. Please use driver with special head for removed and install nozzle as. (figure 3)
2. Please remove nozzle (figure 4) from burner with special nozzle driver and install new nozzle. (figure 5)
   

VENTILATION OF ROOM
The air needed for burning is received from room air and the gases emitted are given directly in room. For safe operation of your product, good room ventilation is a precondition. If no window or room to be utilized for room ventilation is  available, additional ventilation should be installed.
Room size / Ventilating opening
Smaller than 5 m? / min. 100 cm2
Between 5 m3 – 10 m?/ min. 50 cm2
Bigger than 10 m?/ not required
In basement or cellar / min. 65 cm2

REDUCED GAS FLOW RATE SETTING FOR HOB TAPS

1. Ignite the burner that is to be adjustment and turn the knob to the reduced position.

2. Remove the knob from the gas tap.

3. Use an appropriately sized screwdriver to adjust the flow rate adjustment screw. For LPG (butane-pro pane) turn the screw clockwise.
   For the natural gas, you should turn the screw counter- clockwise once. “The normal length of a straight flame in the reduced position should be 6-7 mm.”

4. If the flame is higher then the desired position, turn the screw clockwise. If it is smaller turn anticlockwise.

5. For the last control, bring the burner both to high-flame and reduced positions and check whether the flame is on or off.
   Depending on the type of gas tap used in your appliance the adjustment screw position may vary.
   To adjust your oven acc. to the gas type, make the adjustment for reduced flame carefully by turning with a small screwdriver as shown below on the screw in the middle of the gas cocks as well as nozzle changes (figure 6 and 7).

ELECTRICAL CONNECTION

1. Your oven requires 16 or 32 Ampere fuse according to the appliance’s power. If necessary, installation by a qualified electrician is recommended.
2. Your oven is adjusted in compliance with 220-240V AC/380-415VAC 50/60Hz.electric supply. If the mains are different from this specified value, contact your authorized service.
3. Electrical connection of the oven should only be made by the sockets with earth system installed in compliance with the regulations. If there is no proper socket with earth system in the place where the oven will be placed,  immediately contact a qualified electrician. Manufacturer shall never be responsible from the damages that will arise because of the sockets connected to the appliance with no earth system. If the ends of the electrical connection  cable are open, according to the appliance type, make a proper switch installed in the mains by which all ends can be disconnected in case of connecting / disconnecting from / to the mains.
4. If your electric supply cable gets defective, it should definitely be replaced by the authorized service or qualified electricians in order to avoid from the dangers.
5. Electrical cable should not touch the hot parts of the appliance.
6. Please operate your oven in dry atmosphere.

THIS PAGE IS INTENTIONALLY LEFT BLANK

YOUR RANGE COOKER

ACCESSORIES

1. Deep Tray
   Used for pastries, deep fried foods and stew recipes. In case of frying directly on the grill for cakes, frozen foods and meat dishes, it can be used of oil pick-up tray.
   

2. Wire Grill
   Used for frying and/or placing the foods to be baked, fried and frozen foods on the desired rack.
   

3. In tray wire grill
   Foods that can stick while cooking such as beef are placed on in tray grill. Thus, the contact and sticking of the food is prevented.

4. Splash back
   The resulting temperature of the oven chimney avoid contact with the wall.

TECHNICAL SPECIFICATIONS

WARNING: For the modification to be done by authorised service, this table should be considered.
Manufacturer may not be held responsible for any problems rising because of any faulty modification.
WARNING: In order to increase the product quality, the technical specifications may be changed without prior notice.
WARNING: The values provided with the appliance or its accompanying documents are laboratory readings in accordance with the respective standards. These values may differ depending on the use and ambient conditions.

INSTALLATION OF YOUR OVEN

1. Lamp
2. Oven Temperature Controls
3. Display Screen
4. Front Left burner
5. Rear Left burner
6. Central burner
7. Rear Right burner
8. Front Right burner

WARNING: The control panel above is only for illustration purposes.
Consider the control panel on your device.

BURNER SPECIFICATIONS

Burner Specifications

| G20,20 mbar G25,25 mbar| G30,28-30 mbar G31,37 mbar
---|---|---
Gas natural| LPG

Wok Burner (3,5)

| Injector| 1,40| mm| 0,96| mm
Gas flow| 0,333| m³/h| 254| g/h
Power| 3,50| kW| 3,50| kW

Rapid Burner

| Injector| 1,15| mm| 0,85| mm
Gas flow| 0,276| m³/h| 211| g/h
Power| 2,90| kW| 2,90| kW

Semi-Rapid Burner

| Injector| 0,97| mm| 0,65| mm
Gas flow| 0,162| m³/h| 124| g/h
Power| 1,70| kW| 1,70| kW

Auxiliary Burner

| Injector| 0,72| mm| 0,50| mm
Gas flow| 0,96| m³/h| 69| g/h
Power| 0,95| kW| 0,95| kW

Grill Burner

| Injector| 1,10| mm| 0,78| mm
Gas flow| 0,238| m³/h| 182| g/h
Power| 2,50| kW| 2,50| kW

Oven Burner

| Injector| 1,30| mm| 0,92| mm
Gas flow| 0,333| m³/h| 254| g/h
Power| 3,50| kW| 3,50| kW

INSTALLATION INSTRUCTIONS

INSTALLATION OF YOUR OVEN
Check if the electrical installation is proper to bring the appliance in operating condition. If electricity installation is not suitable, call an electrician and plumber to arrange the utilities as necessary.
Manufacturer shall not be held responsible for damages caused by operations performed by unauthorized persons.
WARNING: It is customer’s responsibility to prepare the location the product shall be placed on and also to have the electrical installation prepared.
WARNING: The rules in local standards about electrical installations shall be followed during product installation.
WARNING: Check for any damage on the appliance before installing it.
Do not have the product installed if it is damaged.
Damaged products cause a risk for your safety.

RIGHT PLACE FOR INSTALLATION AND IMPORTANT WARNINGS
Appliance feet should not stay on soft surfaces such as carpets. The kitchen floor shall be durable to carry the unit weight and any other kitchenware that may be used on the oven.
The appliance is suitable for use on both side walls, without any support, or without being installed in a cabinet. If a hood or aspirator will be installed above the cooker, follow the instructions of the manufacturer for height of mounting.  (min. 650 mm)
WARNING: The kitchen furniture near the appliance must be heat resistant.
WARNING: Do not use the door and/or handle to carry or move the appliance.
WARNING: Do not install the appliance beside refrigerators or coolers.
Heat radiated by the appliance increases the energy consumption of cooling devices.

INSTALLATION OF THE OVEN FEET

Follow these instructions to install the oven feet;

1. Foot attachment lath is installed on the oven from the bottom of the oven as shown in (figure 10). Nuts are centered on these lathes in order to screw feet. Complete the feet installation process by screwing the feet to the nuts (figure  11).
2. You can balance your oven by turning the screwed feet according to the surface type you are using.
3. If your oven has plastic food as in (figure 12) you can adjust your ovens height from these feet as turned clockwise or anticlockwise.
   

CHAIN LASHING
Before using the appliance, in order to ensure safe use, be sure to fix the appliance to the wall using thechain and hooked screw supplied. Ensure that the hook is screwed into the wall securely.

INSTALLING THE OVEN DOOR

OPERATION INSTRUCTIONS

TIME OF DAY ADJUSTMENT
Press to the “clock” button. The “•” icon between the hours and minutes will start to flash.
Using the “–” and “+” buttons, you can adjust the current time of day. Long presses of those buttons will enable fast adjustments.
Pressing the “clock” button for a long time, until the hour and “•” between the hours and minutes start to flash; will enable you to adjust just the hours portion of the display.
MINUTE MINDER ADJUSTMENT
Press to the “+” button. The screen will return to displaying the ‘0.00’ and the bell symbol will start to flash.
You can adjust the minute minder using the “+” and “–” buttons. After 6 seconds following the adjustment, the bell symbol will be stabilized. The minute minder will start to countdown.
The minute minder time increments are in 10 seconds up to 99 minutes 50 seconds, thereafter the display will show 1 hour and 40 minutes and the adjustment will be in 1 minute steps up to the 10 hours.
Note: In order to cancel a minute minder program, set the minute minder time down to 0.00 or press to the “–” and +” buttons together.
CANCELLING THE BUZZER SOUND
When countdown of the minute minder is completed, the screen will return to displaying the current time of day. The bell symbol will start to flash; a buzzer alarm is heard and will sound, if not stopped, for 7  minutes. Press any button to  cancel the sound.
BUZZER TONE ADJUSTMENT
You may adjust the buzzer tone of the timer in the following way:

1. Pressing the “–” button, you can hear the currently set tone.
2. Releasing “–” and then pressing again, you can hear the next available (total 3) tone.
3. The last sound heard will be your adjusted one.
   Note: After prolonged blackouts all functions will default to their factory settings and require reprogramming.

FUNCTION BUTTON
Used for determining the heaters to be used for cooking the dish to be cooked in the oven. Heater program types in this button and their functions are described below. All heater types and program types consisting of these heaters may  not be available at all models.

USING OVEN BURNERS

1. If your oven equipped with burners that operates with gas, appropriate knob should be used in order to ignite the burners. Some models have automatic ignition from the knob; it is easy to ignite the burner by turning the knob. Also, burners can be ignited by pressing the ignition button or they can be ignited with a match.
2. Do not continuously operate the igniter for more than 15 seconds. If the burner does not ignite, wait minimum one minute before trying again. If the burner is extinguished for of the any reason, close the gas control valve and wait a minimum of one minute before trying again.

USING OVEN HEATING ELEMENTS

1. When your oven is operated first time, an odour will be spread out which IS from using the heating elements. In order to get rid of this, operate it at 250 °C for 45-60 minutes while it is empty.
2. Position the oven control knob to the desired temperature to begin operation.
3. Kinds of meals, cooking times and thermostat positions are given in cooking table. The values given in the cooking table are characteristic values and were obtained as a result of the tests performed in our laboratory. You can find  different flavours suitable for your taste depending on your cooking and using habits.
4. You can make chicken revolving in your oven by means of the accessories.
5. Cooking times: The results may change according to the area voltage and material having different quality, amount and temperatures.
6. During the time when cooking is being performed in the oven, the oven door should not be opened frequently. Otherwise circulation of the heat may be imbalanced and the results may change.

USING THE GRILL

1. When you place the grill on the top rack, the food on the grill shall not touch the grill.
2. You can preheat for 5 minutes while grilling. If necessary, you may turn the food upside down.
3. Food shall be in the center of the grill to provide maximum air flow through the oven.

To turn on the grill;

1. Place the function button over the grill symbol.
2. Then, set it to the desired grill temperature.

To turn the grill off;

1. Set the function button to the off position.
   WARNING: Keep the oven door closed while grilling. (electrica grill)
   WARNING: Keep the oven door closed while grilling. (gas grill)

USING THE CHICKEN ROASTING
Place the spit on the frame. Slide turn spit frame into the oven at the desired level. Locate a dripping pan through the bottom in order to collect the fast.
Add some water in dripping pan for easy cleaning.
Do not forget to remove plastic part from spit. After grilling, screw the plastic handle to the skewer Figure 13 and take out the food from oven.

USING GAS BURNERS
Flame cut-off safety device (FFD); operates instantlywhen safety mechanism activates due to overflown liquid over upper hobs.

1. The valves controlling the gas cookers have special security mechanism. In order to light the cooker always press on the switch forward and bring it to flame symbol by turning counter- clockwise. All of the lighters shall operate and  the cooker you controlled shall light only. Keep the switch pressed until ignition i performed. Press on the lighter button and turn the knob counter clockwise.
2. Do not continuously operate the igniter for more than 15 seconds. If the burner does not ignite, wait minimum one minute before try again.
3. In models with gas security system, when flame of the cooker is extinguished, control valve cuts off the gas automatically. For operate the burners with gas security system you must press the knob and turn counter-clock-wise. After  the ignition you must wait nearly 5-10 second for gas security systems activation. If the burner is extinguished for of the any reason, close the gas control valve and wait a minimum of one minute before trying again.
4. Closed Fully open Half open
5. Before operating your hob please make sure  that the burner caps are well positioned. The right placement of the burner caps are shown as below.

CLEANING AND MAINTENANCE

1. Disconnect the plug supplying electricity for the oven from the socket.
2. While oven is operating or shortly after it starts operating, it is extremely hot. You must avoid touching from heating elements.
3. Never clean the interior part, panel, lid, trays and all other parts of the oven by the tools like hard brush, cleaning mesh or knife. Do not use abrasive, scratching agents and detergents.
4. After cleaning the interior parts of the oven with a soapy cloth, rinse it and then dry thoroughly with a soft cloth.
5. Clean the glass surfaces with special glass cleaning agents.
6. Do not clean your oven with steam cleaners.
7. Before opening the upper lid of the oven, clean spilled liquid off the lid. Also, before closing the lid, ensure that the cooker table is cooled enough.
8. Never use inflammable agents like acid, thinner and gasoline when cleaning your oven.
9. Do not wash any part of your oven in dishwasher.
10. In order to clean the front glass lid of the oven; remove the fixing screws fixing the handle by means of a screwdriver and remove the oven door. Than clean and rinse it thoroughly. After drying, place the oven glass properly and re- install the handle.

CLEANING AND MAINTENANCE OF THE OVEN’S FRONT DOOR GLASS
Remove the profile by pressing the plastic latches on both left and right sides as shown in figure 21 and pulling the profile towards yourself as shown in figure 22. Then remove the inner-glass as shown in figure 23. If required, middle  glass can be removed in the same way. After cleaning and maintenance are done, remount the glasses and the profile in reverse order. Make sure the profile is properly seated in its place. 

*CATALYTIC WALLS
Catalytic walls are located on the left and the right side of cavity under the guides. Catalytic walls banish the bad smell and obtain the best performance from the cooker. Catalytic walls also absorb oil residue and clean your oven while it’s
operating.
REMOVING THE CATALYTIC WALLS**
In order to remove the catalytic walls; the guides must be pulled out.
As soon as the guides are pulled out, the catalytic walls will be released automatically. The catalytic walls must be changed after 2-3 years.

CHANGING THE OVEN LAMP
WARNING: To avoid electric shock, ensure that the appliance circuit is open before changing the lamp. (having circuit open means power is off)
First disconnect the power of appliance and ensure that appliance is cold.
Remove the glass protection by turning as indicated in the figure on the left side. If you have difficulty in turning, then using plastic gloves will help you in turning.
Then remove the lamp by turning, install the new lamp with same specifications.
Reinstall glass protection, plug the power cable of appliance into electrical socket and complete replacement. Now you can use your oven.
Type G9 Lamp

TROUBLESHOOTING

In case you experience a problem with your oven, first check the table below and try the suggestions before calling the technical service.

Problem

| Possible Cause|

What to do

---|---|---
Oven does not operate| Power Supply not available Gas Supply not available| Check for power supply
Check if main gas valve is open.
Check if gas pipe is bent or kinked. Make sure gas hose is connected to oven.
Check if a suitable gas valve is being used.
Oven stops during cooking| Plug comes out from the wall socket.| Re- install the plug into wall socket.
Turns off during cooking| Too  long  continuous  operation
More than one plug in a wall socket.| Let the oven cool down after long cooking cycles.
Use only one plug for each wall socket.
Oven door is not opening properly| Food residues jammed between the door and internal cavity.| Clean the oven well and try to re-open the door.
Lighter  not  operating.| Tips or body of ignition plugs are clogged.
Gas burner pipes are clogged.| Clean tips or body of ignition plugs of gas burners
Clean gas burner pipes.
Electric shock when touching the oven.| No proper grounding.
Ungrounded wall socket is used.| Make sure power supply is grounded properly.
Water  dripping.
Steam coming out from a crack on oven door.
Water remaining inside the oven.| Water or steam may generate under certain conditions depending on the food being cooked. This is not a fault of the  appliance.| Let the oven cool down and than wipe dry with a dishcloth.
Oven does not heat.| Oven door is open.
Oven controls not correctly adjusted.
Fuse tripped or circuit breaker turned off.| Close the door and restart.
Read the section  regarding  operation of the oven and reset the oven.
Replace the fuse or reset the circuit breaker. If this is repeating frequently, call an electrician..

ENVIRONMENTALLY-FRIENDLY DISPOSAL
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical0 and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the frame work for the return and recycling of used appliances as applicable throughout to the EU.
ENVIRONMENTALLY-FRIENDLY DISPOSAL

PACKAGE INFORMATION
Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them  to the packaging material collection points designated by the local authorities.

PRODUCT SPECIFICATIONS

PRODUCT FICHE

Comply with Energy Label Directive Eu 2010/30/EU – Regulation No 65/2014 of ovens according to EN 60350- 1 or EN 15181
Comply with EU directive 2009/125/EC – regulation No 66/2014 according to EN 60350-1 or EN 15181
Brand| TEKNIX
Model| TKGF91SS

Type of oven

| Free Standing| X
Built-in|
Mass of the appliance(M)(Net weight)kg| –| kg
Number of cavities| 1

Heat source per cavity

| Electrical|
Gas| X
Mix|
Volume per cavity| 97| l
Energy consumption (electricity) required to heat a standardised load in a cavity of an electric heated oven during a cycle in conventional mode per cavity (electric final energy)| ****

EC electric cavity

| ****

—

| ****

kWh/cycle

Energy consumption required to heat a standardised load in a cavity

of an electric heated oven during a cycle in fan-forced mode per cavity (electric final energy)

| EC

electric cavity

| ****

—

| ****

kWh/cycle

Energy consumption required to heat a standardised load in a gas- fired cavity of an oven during a cycle in conventional mode per cavity

(gas final energy)

| EC gas cavity| 7,41

2,06

| MJ/cycle kWh/cycle (‘)
Energy consumption required to heat a standardised load in a gas- fired cavity of an oven during a cycle in fan-forced mode per cavity

(gas final energy)

| EC gas cavity| —

—

| MJ/cycle kWh/cycle (‘)
Energy Efficiency Index per cavity| EEI cavity| 95|
Energy Efficiency Class| X
(¹) 1 kWh/cycle = 3,6 MJ/cycle.
PRODUCT FICHE
Information For Domestic Gas-Fired Hobs
Comply With Eu Directive 2009/125/EC- Regulation No 66/2014 according to EN 30-

2-1

Brand| TEKNIX
Model| TKGF91SS

Type Of Hob

| Electrical|
Gas| X
Mix|
Number of gas burners| 5

Energy efficiency per gas burner EE gas burner

| Front Left Zone| 56
Rear Left Zone| 56
Front Right Zone| 55,5
Rear Right Zone| —
Center Zone| 55,1
Rear Center Zone| —
Energy Efficiency For The Gas Hob EE Gas Hob| 55,7

WARRANTY

Your Teknix appliance comes with a 2 year parts and labour guarantee.
Please REGISTER your appliance online at

www.teknixwarranty.co.uk

We, Teknix, undertake that if within 24 months of the date of purchase this appliance or any part thereof is proven to be defective by reason of mechanical or electrical failure we will at our discretion repair or replace the same free of any  charge for labour, materials or carriage on condition that:

90CM RANGE COOKER SINGLE CAVITY
WWW.TEKNIX.CO.UK
TKGF91SS
USER MANUAL

References

• Teknix | Home Appliances
• Warranty Registration — Teknix | Home Appliances
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>