Inrico S350 5G PoC Professional Intelligent Terminal User Guide

Inrico S350 5G PoC Professional Intelligent Terminal

Specifications

• GSM/GPRS/EDGE: 850/1900
• WCDMA: Band 2/4/5
• LTE: Band 2/4/5/7/12/13/17/26/38/40/41/66
• 5G NR Band: SA n2/5/7/26/38/41/66

Notes Before Using

Please read the following content carefully. It is very important for radio users to gain general knowledge and risks.

• Do not use the device or charging the battery in any hazardous areas such as gas, dust, steam, etc.
• Please turn off the device while refueling or parking at the gas station.
• Do not disassemble your radio
• Avoid prolonged time in the sun or placing it near heating appliance.
• Avoid excessive exposure to the extreme dusty, damp and splashing place, or leave it on unstable surface.
• Repairation by professional technicians, do not disassemble by yourself.

Disclaimer

lnrico reserves the right to modify product design and specifications. lnrico assumes no responsibility in the event of printing errors. All specifications are subject to change without notice.

Unpacking and checking the equipments
Please pull out of the equipments carefully from the packag­ing box, and we recommend you check the items are listed in the following table before you abandon the package, and make sure you receive all of them. If any items are lost or damaged druing the transportation, please contact local dealer immediately.

Accessories

Battery Care

Fully Charge Battery Before Initial Use

• Do preserve battery life by switching off a device and removing the batteries when it’s not being used, and is not expected to be used for extended periods of time.
• Do practice proper battery storage by keeping batteries in a cool, dry place at normal room temperature. Properly Store Batteries
• Remove the battery from the device.
• Charge and discharge the battery to 40%-65% if it will not be used for 10 days or more. This can greatly extend the battery life.
• The battery should drop below 65% when it is idle for more than 10 days to prevent it from swelling.
• Store the battery in cool and dry environment that’s less than 25°C.

Features of Lithium Battery

• Battery capacity will reduce after multiple charging cycles.
• The battery capacity drops gradually even without being used.
• Longer charging time is required in shady place.
• Charging and storing lithium battery in warm condition will short its lifespan. Please do not leave them inside the vehicle or near the heater.
• If the battery working time has reduced significantly, please replace the battery immediately in avoidance of fluid leakage.

Handling Precautions

• Do not overcharge the battery Please stop charging if it can’t be fully charged within required time. The battery probably overheats, smokes, bursts or suddenly be on fire due to abnormal charging process. When fully charged or not charged, please disconnect the charger and unplug it from the power outlet.
• Do not discard battery in a microwave or high pressure container. The battery probably overheats, smokes, bursts or suddenly be on fire.
• Do not expose damaged battery near any fire. If the battery is broken, leaking or has an abnormal odor, please remove it from flammable areas immediately. The fluid in the battery is flammable, which may cause smoke and fire.
• Do not use abnormal battery If the battery is with odd smelly, discolored, deformed, etc., please stop charging or disassemble from the device immediately
• Please use authorized power adaptor To comply with warranty terms and avoid damages, charge the battery using a specified charger for best performance.

USB cable charging

Plugging the USB-C cable to the radio charging port and another end USB-A interface connect with power adapter LED indicator light on for charging after power supplied.

Accessory Installation

1. To insert a SIM card, TF card
   

2. Install lanyard
   

3. Installing headset
   Open the cover from the top of device to show the headset sockets. Headset will work immediately after being pluggedin.

Radio Overview

PTT| Long press| Press to initiate POC group call in idle state, release to end group call;
Fl| Short press| Replay the last ten recordings (customizable function)
Long press| Flashlight switch
F2| Short press| increase volume
Long press| Maximum volume
F3| Short press| Reduce volume
Long press| Volume Min
F4| Short press| Open the camera application in standby mode; Take a

photo in photography mode,Sta rt/sto p recording in recording mode;

Long press| Volume Min
sos| Long press| Initiate SOS emergency calls within the POC group
power supply| Short press| Lock screen / unlock; Lock screen status supports fingerpr int unlocking and bright screen,Unlock and enter directly
kiss| Touch to unlock the bright screen in lock mode, and directly enter after unlocking
Long press| Turn on/off

Icon Function Indication lcom

LED Indicators

1 seconds

Low battery| Red| Illuminates every

3 seconds

Charging state| Red| Light
Charge Complete| Green| Light

Basic Function

• Poweron
  Press and hold the on/off button for 3 seconds,
  wait for the power on and wait for the program to start

• Shutdown
  Long press the on/off button, and then operate the shutdown menu to shut down.

• Call usage
  Press the PTT key to start a call. If the current session is occupied, that is, someone else is currently Call, PTT key invalid. The maximum call time for individual terminal devices is limited to 60 seconds If it exceeds 60 seconds, the call authority will be automatically released.

Network Connecting

Wi-Fi Connecting
After the device is turned on and the main screen shows up, click the “Settings ” icon and find the Wi-Fi icon, then click to enter the check box, make sure the right side “On” button been switched on, choose the wireless network you want to connect,enter the password for connecting.

Cellular Network Connecting
Find the “Data usage” in “Settings ” and click to enter the check box, switch on & activate the “Cellular data “button, choose the Cellular Network you required.

If you are using dual cards, please click SIM cards. After selecting the card you want to set up, you can go online normally.

Application Management

After the device is turned on and the main screen shows up, click the “Settings ” icon and find the Wi-Fi icon, then click to enter the check box, make sure the right side “On” button been switched on, choose the wireless network you want to connect.enter the password for connecting.

In order to uninstall APP from your device
Follow the steps listed below: Settings — Apps — Selecting the App — UN INSTALL

Clear the application data or cache
Settings –Apps — Selecting the App — CLEAR DATA

The Non-systematic APP stops running

Simple Troubleshooting

Specification

FCC Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information

SAR tests are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. Before a new model phone is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, tests for each phone are performed in positions and locations as required by the FCC.
For body worn operation, this model phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 10mm from the body.
Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>