UNIVER KF-17032 Ball Head Joint Bearing Instruction Manual
- June 16, 2024
- UNIVER
Table of Contents
Instruction Manual Ø 32 ÷ 125 mm – ISO 15552 Pneumatic Cylinders
CLEAN PROFILE
KL
CHARACTERISTICS
| Ambient temperature | -20 ÷ 80 °C |
|---|---|
| Fluid | fi ltered air, with or without lubrication |
| Working pressure | 1,5 ÷ 10 bar |
| End-caps | die-cast aluminium |
| Barrel | anodized aluminium |
| Piston | die-cast aluminium |
| Guide slide | acetalic resin |
| Piston rod | chromium-plated steel, stainless steel upon request |
| Piston seal | NBR |
| Guide bush for piston rod | UNIVER Original self-lubricating and self-aligning |
| Shock absorber seals | NBR |
| Cushionings | adjustable on both sides |
| Other available versions | tandem, two-position tandem, |
| opposed, with common piston rod (upon request) |
CODIFICATION KEY
-
Series
KL = Ø 32÷125 mm – ISO 15552
Pneumatic Cylinders
Magnetic version standard supplied -
Type
1 = Stainless steel piston rod
2 = Chromium-plated steel piston rod -
Version
D.A. = Double acting
S.A. = Single acting
00 = D.A. Standard version
01 = D.A. Through piston rod
60 = S.A. Retracted piston rod Max stroke 50 mm
70 = S.A. Extended piston rod Max stroke 50 mm -
Bore (mm)
032 = Ø32
040 = Ø40
050 = Ø50
063 = Ø63
080 = Ø80
100 = Ø100
125 = Ø125 -
Stroke (mm)
0025 = 25
0050 = 50
0075 = 75
0080 = 80
0100 = 100
0125 = 125
0150 = 150
0160 = 160
0175 = 175
0200 = 200
0250 = 250
0300 = 300
0320 = 320
0350 = 350
0400 = 400
0450 = 450
0500 = 500
0600 = 600
0700 = 700
0800 = 800
0900 = 900
1000 = 1000 -
Option
F = Preset for locking unit reduced protrusion
G = Preset for locking unit ISO protrusion -
Magnetic
M = Magnetic version standard supplied -
ATEX option
X = Atex (upon request)
See ATEX Catalogue for types and versions
KL190 and KL290 versions with high temperature seals (Max 120°C) and versions with low temperature seals (Max -30°C) available upon request
FIXING ELEMENTS AND ACCESSORIES
Ø| Articulated rear male
hinge| Rear male hinge| Front/rear flange| Angle bracket| Front/rear hinge
with
fl oating pin| Hinge support| ISO intermediate
hinge| DF sensor and DHF covering strip
---|---|---|---|---|---|---|---|---
| | | | | | | |
32| KF-11032S| KF-11032| KF-12032| KF-13032| KF-14032AP| KF-41032| KLF-14032|
DF
DHF-0020100
40| KF-11040S| KF-11040| KF-12040| KF-13040| KF-14040AP| KF-41040050|
KLF-14040
50| KF-11050S| KF-11050| KF-12050| KF-13050| KF-14050AP| KF-41040050|
KLF-14050
63| KF-11063S| KF-11063| KF-12063| KF-13063| KF-14063AP| KF-41063080|
KLF-14063
80| KF-11080S| KF-11080| KF-12080| KF-13080| KF-14080AP| KF-41063080|
KLF-14080
100| KF-11100S| KF-11100| KF-12100| KF-13100| KF-14100AP| KF-41100125|
KLF-14100
125| KF-11125S| KF-11125| KF-12125| KF-13125| KF-14125AP| KF-41100125|
KLF-14125
-
= If employed with articulated rear male hinge diameter 50-80 use KF-11050SSA (pin Ø16) and KF-11080SSA (pin Ø20)
KL Ø 32 ÷ 125 mm – ISO 15552 Pneumatic Cylinders Tube profi le with integrated sensor grooves
UNIVER Original since 2005
Recessed sensor
DF series Magnetic piston standard supplied
Fixing screws integrated in the end-cap profile Sensor grooves available in different positions
Possibility to mount DH sensors with brackets Intermediate hinge with locking system guaranteed by UNIVER AUTOMOTIVE expertise
Standard fi xing elements
UNIVER Original
- Die-cast end-caps in aluminium
- Die-cast piston in aluminium
- Guide slide in acetalic resin with integrated magnetic ring
- Wear-resistant shock absorber seals in nitrilic rubber compound
- Lip piston seals in nitrile rubber compound
- UNIVER Original self-aligning and self-lubricating guide bush for piston rod
Other available versions
Documents / Resources
|
UNIVER KF-17032 Ball Head Joint
Bearing
[pdf] Instruction Manual
KF-17032 Ball Head Joint Bearing, KF-17032, Ball Head Joint Bearing, Head
Joint Bearing, Joint Bearing, Bearing
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>