ANCEL 2024 V5BT OBD2 Scanner Diagnostic Tool User Manual

ANCEL 2024 V5BT OBD2 Scanner Diagnostic Tool

Product Information

Specifications:

• Manufacturer: OBDSPACE TECHNOLOGY CO., LTD.
• Model: [Product Model]
• Power Source: Safety grounded outlet
• Compatibility: [List of compatible devices]

Product Usage Instructions

Statement

You must carefully read the instruction manual, especially the safety instructions, before you can connect, commission, and operate the products of OBDSPACE TECHNOLOGY CO., LTD. (hereinafter referred to as OBDSPACE).

Agreement

Once the product is used, it is an endorsement of the following:

1. Please refer to the packing list of the random distribution for the configuration equipment of this product, whichever is the actual product.
2. The functions and pictures described in this manual are subject to the actual software. All information, specifications, and illustrations in the manual are the latest information at the time of publication. The company reserves the right to change it without notice.

Copyright information

It cannot be copied or stored in any form (electronic, mechanical, photocopying, recording, or otherwise) without prior written permission being secured from OBDSPACE. Software and data are owned by technology and protected by copyright laws, international contract law, and other national laws. It is strictly forbidden to copy or transfer the data and software or some of the contents. If there is any violation, the technology will be held legally responsible according to law.

Disclaimer

[Insert disclaimer information]

Safety Information

For the safety of yourself and others, and to avoid damage to equipment and vehicles, all personnel handling the equipment must read the safety precautions mentioned in the manual.

Inspection Precautions

1. Ancel V5 & V5 BT can only be connected to a safety outlet that is grounded. Before connecting, check and confirm that the diagnostic circuit is in good condition. Otherwise, it is not necessary to test to avoid damage to the main unit. If necessary, use a multimeter to measure the diagnostic seat voltage.
2. Use only the power cord supplied with the OBDSPACE diagnostics or detected power line.
3. Pay special attention to the effects or damage caused by environmental factors such as acid and alkali, poison gas, and heavy pressure.
4. Exhaust gases from the engine contain a variety of toxic compounds and should be avoided. Park the vehicle in awell-ventilated area before operation.
5. Do not place the device on the vehicle’s power distribution unit. Strong electromagnetic interference can cause damage to the equipment.
6. After the equipment is installed successfully, before starting the engine, make sure that the parking brake is pulled and the speed lever is placed in the neutral or parked position to avoid accidents when the vehicle is started.
7. When the engine is running at a high temperature, avoid contact with high-temperature components such as the water tank and the exhaust pipe. At the same time, be careful of the voltage generated by the components such as the ignition coil, the distributor cover, the ignition circuit, and the ignition plug during engine operation.

FAQ

Q: Can I use any power cord with the OBDSPACE diagnostics?

A: No, you should only use the power cord supplied with the OBDSPACE diagnostics or the detected power line. Using other power cords may cause damage to the equipment.

Q: How should I handle exhaust gases from the engine during operation?

A: Exhaust gases from the engine contain toxic compounds. It is recommended to park the vehicle in a well-ventilated area before operation to avoid exposure.

1. Statement

You must carefully read the instruction manual, especially the safety instructions, before you can connect, commission and operate the products of OBDSPACE TECHNOLOGY CO., LTD., Ltd. (hereinafter referred to as “OBDSPACE”).

Agreement
Once the product is used, it is an endorsement of the following:

1. Please refer to the packing list of the random distribution for the configuration equipment of this product, whichever is the actual product;
2. The functions and pictures described in this manual are subject to the actual software. All information, specifications and illustrations in the manual are the latest information at the time of publication. The company reserves the right to change it without notice.

Copyright information
It cannot be copied or stored in any form(electronic, mechanical, photocopying, recording or otherwise) without prior written permission being secured from OBDSPACE. Software and data are owned by technology and protected by copyright laws, international
contract law, and other national laws. It is strictly forbidden to copy or transfer the data and software or some of the contents. If there is any violation, the technology will be held legally responsible according to law.

Disclaimer

1. This manual only provides the operation and operation methods for Ancel V5 & V5 BT. The company does not assume any responsibility for the consequences caused by using the operation methods for other equipment operations.
2. The company shall not accept any responsibility for accidents caused either by the user personally or anyone else, or costs and expenses due to equipment damages including equipment loss caused by the user’s abuse or misuse, arbitrary changes or repairs or operation of the equipment in a manner not in accordance with the manual requirements.

Safety Information
For the safety of yourself and others, and to avoid damage to equipment and vehicles, all personnel handling the equipment must read the safety precautions mentioned in the manual.

Inspection Precautions

1. Ancel V5 & V5 BT can only be connected to a safety outlet that is grounded. Before connecting, check and confirm that the diagnostic circuit is in good condition. Otherwise, it is not necessary to test to avoid damage to the main unit. If necessary, use a multimeter to measure the diagnostic seat voltage.
2. Use only the power cord supplied with the OBDSPACE diagnostics or detected power line.
3. Pay special attention to the effects or damage caused by environmental factors such as acid and alkali, poison gas, and heavy pressure.
4. Exhaust gases from the engine contain a variety of toxic compounds and should be avoided. Park the vehicle in a well ventilated area before operation.
5. Do not place the device on the vehicle’s power distribution unit. Strong electromagnetic interference can cause damage to the equipment.
6. After the equipment is installed successfully, before starting the engine, make sure that the parking brake is pulled and the speed lever is placed in the neutral or parked position to avoid accidents when the vehicle is started.
7. When the engine is running at a high temperature, avoid contact with high temperature components such as the water tank and the exhaust pipe. At the same time, be careful of the voltage generated by the components such as the ignition coil, the distributor cover, the ignition circuit and the ignition plug during engine operation.

Notes on the use of the instrument

1. This instrument is a precision electronic instrument. Do not drop it. Handle it as gently as possible, away from heat and electromagnetic fields.
2. Ensure that the instrument and diagnostics are well connected so that signal interruptions do not affect the test.
3. Use screws as much as possible when using the cables and connectors to avoid disconnecting and damaging the connectors when moving. Hold the front end of the connector when pulling the connector, and avoid pulling the rear cable to avoid damage to the diagnostic interface.
4. When the electrical components are energized, the circuit cannot be disconnected to prevent self-inductance, mutual inductance and current sensors and the vehicle ECU.
5. The operation of this instrument requires a certain basis for vehicle inspection and maintenance, and has a certain understanding of the electronic control system of the vehicle under test.

Operating car ECU considerations

When performing diagnostic operations on a vehicle equipped with a computer control system, the following should be noted:

1. Do not place magnetic objects such as radio speakers close to the computer, as the magnetic properties of the speakers can damage the circuits and components in the ECU.
2. When the ignition switch is turned on, the internal electrical equipment of the car must not be disconnected. Due to the self-inductance of the coil when disconnected, a high instantaneous voltage will be generated, which will cause damage to the sensor and ECU;
3. When performing repairs near a computer or sensor, special care should be taken to avoid damage to the ECU and sensor;
4. When carrying out maintenance work on or near the ECU-controlled digital meter, be sure to wear a metal strap with one end clamped to the body and the other end wrapped around the wrist;
5. When performing welding work on a car, the ECU system power should be turned off beforehand;
6. Do not use test lights to test ECU-related electrical devices to prevent damage to the ECU or sensor unless specifically stated;
7. Test ECU and sensors cannot be tested with a pointer-type ohmmeter, unless otherwise specified in the test procedure, but should be tested with a high-impedance digital meter.

Product Description

Product Overview
Ancel V5 & V5 BT is an Android based brand new-generation overall diagnostic tool for heavy-duty trucks and commercial vehicles and machineries. With 7 -inch high-qualified industrial diagnostic tablet, in which software covering more trucks, buses, machineries from home and abroad with extensive diagnostic functions. Featuring a new diagnostic experience and cost performance, it can be a better choice for all users.

Tablet parameter

life:5H

Speaker| Double speakers 8Ω/1W
Interface| Type-C,TF card slot(support SDHC/SDXC)
Network| WIFI 802.11b/g/n
---|---
Bluetooth| Bluetooth 2.1/4.0
Input voltage| 5V/2A
Working

temperature

| -10 to 70℃(14-158℉),relative humidity:<90%
Storage

temperature

| -30 to 120℃(-22 to 248℉),relative

humidity:<90%

Dimensions(WxHxD)| 270 mm(10.63 in) x 193 mm(7.60 in) x 38

mm(1.50 in)

Weight| NW: 1.20 kg (2.65 lb) GW: 3.00 kg (6.61 lb)
Protocols| ISO 9141-2, ISO 14230-2, ISO 15765-4, K/L-Line, SAE-J1850 VPW, SAE-J1850 PWM, CAN ISO 11898,

Highspeed, Middlespeed, Lowspeed and Singlespeed CAN, GM UART, UART Echo Byte Protocol, Honda Diag-H Protocol, TP2.0, TP1.6,

SAE J1939, SAE J1708, Fault-Tolerant CAN etc.

V5 Tablet interface instruction

V5 BT Tablet interface instruction

V5 BT VCI instruction

V5 BT VCI Parameter

Humidity:<90%

Storage Temperature| -30 to 120℃（-22-248℉），relative

Humidity:<90%

Protocols

| ISO 9141, ISO14230, ISO15765, ISO11898, SAE-J1850 VPW, SAE-1850 PWM, J1939, J1708, UDS, K/L lines,

High speed CAN, Middle speed CAN,

Low speed CAN and Single wire CAN

Software Introduction

Ancel software client homepage:

Diagnosis
Extensive vehicle coverage for more than 80 Europe, America, Asia, China and Australia vehicle makes.

Hot function
Supporting 10 most commonly used service Reset Functions: OILREST, ABS BLEEDING, BATTERY, DPF, EPB, INJECTOR, SAS, THROTTLE, TPMS, AT SET.

Quick Support
The function allows OBDSPACE technical staff to connect to your host through the network remotely to help you diagnose the vehicle.

DTC Query
The fault information corresponding to the fault code can be quickly retrieved to help the repairer locate the component fault.

Update

• Connect the internet by WIFI.
• Login (input the serial number and password at the first time.
• Select the software and click the download button.

Data Manager
The storage location of vehicle applications, test pictures, videos, reports and for user reference.

Feedback
This function allows you upload vehicle diagnostics problems encountered by users during the use of the software. It can help engineers repair software errors quickly.

First, select the problem type:

Second, select the vehicle brand:

Third, input the problem information, and then click “Submit”.

Settings

Product Activation

1. Enter the【Update】function, input the serial number and the password (you can find the password in the password envelope).

2. Click【Login】, and a prompt box will pop up.

3. Click 【Yes】to fill in the activation information.

4. After the information is filled out, click 【ACTIVATION】.

5. Click【Yes】, complete the product activation.

Cleaning and maintenance and warranty

Cleaning and maintenance

1. Do not disassemble it, try to handle it gently to avoid impact.
2. Place the fault diagnosis device in a flat, dry, temperature-friendly and dust-free place and avoid high temperature and humidity, excessive smoke, easy vibration, direct sunlight, and strong magnetic field storage environment.
3. If the vehicle test operation is not performed for a long time, please run the main machine regularly to avoid moisture.
4. Unplug the power plug when not in use to avoid aging of electrical components caused by long-term power.
5. When the host is dirty, please disconnect the power before cleaning.
6. Do not use a cleaning agent with a corrosive function or any rough cloth to clean the main unit. Only use a soft cloth and a neutral detergent.
7. The surface of the screen can be cleaned with a special wiper for the LCD screen.
8. Do not place anything on the screen to avoid cracking of the screen or damage to internal components.

Warranty
This applies only to products purchased from a product dealer that has been authorized by OBDSPACE. If products are purchased from anyone other than a OBDSPACE authorized product dealer, buyers will be solely responsible for the cost of product maintenance services and will not be eligible to obtain any warranty from OBDSPACE .

1. Product acceptance
   When you receive the product, please be sure to open the package check.
   Please carefully check the product category and quantity according to the attached list. If there are any shortages, errors, damages and other unpredictable abnormal conditions, please keep all the documents of the product and notify us immediately. Otherwise it is considered a waiver of the claim.

2. Product warranty
   Beginning on the date of purchase(subject to valid purchase proof and effective warranty card of the product), if the product suffers performance failure within one month which is not caused by deviation from the recommended operation or by uncontrollable environmental events, you can choose to have evaluation via our maintenance service or replacement of the product with the same model. After that, there is one year warranty service for the main unit, connectors and power adapter.

3. Product Software Update
   Two-year free software update since activation of product, and will be charged annually after free update session.

4. Not in the scope of the free warranty

   • A. Failures, defects or flaws not directly related to the quality of the OBDSPACE products, including but not limited to failing to use the product according to the user manual’s instructions, crash, fall, disassemble by anyone other than a OBDSPACE approved service person, connecting improper accessories, damage owing to impact because of improper transport or storage of the product, etc.
   • B. Natural wear and tear of the product: including but not limited to cover, keypad, touch screen, accessories, etc.
   • C. Main unit serial number and warranty card serial number discrepancy, product quality inspection tag or bar code removed, altered or damaged.
   • D. Maintenance and modification without the approval of OBDSPACE or its distributors.

Product warranty program

When the product needs to be repaired, please send the product to the local distributor or OBDSPACE, and attach the purchase certificate and warranty card, fill in the following information: company name, contact name, phone number, problem description, purchase invoice.

Note: The valid purchase certificate is an important warranty service certificate. To protect your legal rights, you must obtain a formal invoice from the dealer when purchasing the machine. The name, model number, serial number and purchase date of the product should be clearly stated on the invoice. It is covered with the official seal of the dealer.

Over-warranty product maintenance regulations

If the product needs to be repaired by our company after the maintenance period, we will charge the maintenance fee appropriately, and the freight will be borne by the user.
For products that have passed the warranty period, our technical support personnel will fax the maintenance cost to the user, and will repair it after confirmation by the customer. After confirming, the customer will pay the repair fee to the designated account of our company. After the maintenance fee is received, our company will Can be repaired.

OBDSPACE TECHNOLOGY CO., LTD
D03, Block A, No.973 Minzhi Ave, Longhua District.
Shenzhen, Guangdong, China
Email: support@anceltech.com
Web: www.anceltech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>