SKIWARRIOR G01 Smart Wireless Intercom Audio Ski Goggles User Manual

June 16, 2024
SKIWARRIOR

G01 Smart Wireless Intercom Audio Ski Goggles

Product Information

Specifications

  • Model: 2BDLO-G01B
  • Product Type: Smart Wireless Intercom Audio Ski Goggles
  • Transmitter Type: Low Power
  • RF Signal: Yes
  • Push-to-Talk (PTT) Button: Yes
  • Duty Factor Limit: 50%

Product Usage Instructions

1. Power On/Off

To turn on the Smart Wireless Intercom Audio Ski Goggles, press
and hold the power button located on the side of the goggles. The
LED indicator will light up to indicate the device is powered on.
To turn off the goggles, press and hold the power button again
until the LED indicator turns off.

2. Pairing with Transmitter

Prior to using the intercom feature, you need to pair the
goggles with the transmitter. Follow these steps:

  1. Ensure both the goggles and the transmitter are turned on.

  2. Press and hold the pairing button on the transmitter until the
    LED indicator starts flashing.

  3. On the goggles, press and hold the pairing button located near
    the power button until the LED indicator on the goggles starts
    flashing.

  4. The goggles will automatically search for and connect to the
    transmitter. Once paired, the LED indicators on both devices will
    stop flashing and remain solid.

3. Push-to-Talk (PTT) Functionality

The Push-to-Talk (PTT) button allows you to communicate with
other connected devices. To use the PTT function:

  1. Make sure the goggles are paired with the transmitter.

  2. Press and hold the PTT button on the goggles to activate the
    microphone and start transmitting your voice.

  3. Speak clearly into the microphone located on the goggles.

  4. Release the PTT button to stop transmitting and listen to
    incoming audio from other connected devices.

4. Adjusting Volume

You can adjust the volume of the audio received through the
goggles. Use the volume control buttons located on the side of the
goggles to increase or decrease the volume levels.

5. Charging

The Smart Wireless Intercom Audio Ski Goggles come with a
rechargeable battery. To charge the goggles:

  1. Connect the provided charging cable to the goggles’ charging
    port.

  2. Connect the other end of the cable to a power source, such as a
    USB port on your computer or a wall adapter.

  3. The LED indicator on the goggles will turn red to indicate
    charging is in progress.

  4. Once fully charged, the LED indicator will turn green.

Frequently Asked Questions (FAQ)

Q: Can I use these goggles without pairing them with a

transmitter?

A: Yes, you can still use the goggles for skiing or snowboarding
without pairing them with a transmitter. However, you will not be
able to utilize the intercom functionality.

Q: How far is the range of communication between the goggles

and the transmitter?

A: The communication range can vary depending on environmental
factors, but typically it is around 100 meters (328 feet) in an
open area.

Q: How long does the battery last on a full charge?

A: The battery life can vary based on usage, but on average, it
can last up to 8 hours on a full charge.

2BDLO-G01B

SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. BBeeffoorree aa nneeww ddeevviiccee iiss aa aavvaaiillaabbllee ffoorr ssaallee ttoo tthhee ppuubblliicc,, iitt mmuusstt bbee tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations as required by the FCC. Non-compliance with the above restrictions may result in violation of RF exposure guidelines.
Your Smart wireless intercom audio ski goggles contains a low power transmitter.This product sends out radio frequency (RF) signals when the Push- to-Talk(PTT) button is pressed. The device is authorized to operate at a duty factor not to exceed 50%.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals