trade tested 938680 Fridge Freezer Bottom Mount User Manual
- June 16, 2024
- trade tested
Table of Contents
trade tested 938680 Fridge Freezer Bottom Mount
Product Information
Specifications
- Product Name: Fridge Freezer Bottom Mount 323L Stainless Steel
- Product Code: 938680
- Manufacturer: Trade Tested
Product Usage Instructions
Fridge Components
- Fridge Shelves
- Crisper Cover
- Crisper Fresh Convertible Box
- Fridge Balconies
Freezer Components
- Freezer Drawers
Other Components
- Leveling Feet
Space Requirement
To ensure proper installation and functioning of the refrigerator, please
follow these space requirements:
- Select a location without direct exposure to sunlight.
- Select a location with enough space for the refrigerator doors to open easily.
- Select a location with level (or nearly level) flooring.
- Allow sufficient space to install the refrigerator on a flat surface.
- Allow clearance to the right, left, back, and top when installing. This will help reduce power consumption and keep your energy bills lower.
- Keep at least a 50mm gap at two sides and back.
Positioning
Install this appliance at a location where the ambient temperature corresponds
to the climate class indicated on the rating plate of the appliance:
| Climate Class | Ambient Temperature |
|---|---|
| SN | +10oC to +32oC |
| N | +16oC to +32oC |
| ST | +16oC to +38oC |
| T | +16oC to +43oC |
Electrical Connection
Ensure that the appliance is easily accessible for disconnecting from the
mains power supply after installation.
Door Reversibility
To reverse the door opening direction, follow these steps:
- Unscrew top hinge cover and disconnect the connectors of the door switch and harness.
- Unscrew the top hinge and remove the pin with a screwdriver. Flip the hinge bracket and refit the pin.
- Move the door switch from the right hinge cover to the left hinge cover in the accessory bag.
- Detach the cover on top of the upper door and move the harness from the right side to the left side. Replace the cover.
- Move the top left cover to the right side.
- Take off the upper door and remove the screw from the middle hinge with a cross screwdriver. Take off the lower door.
- Unscrew the bottom hinge and remove the adjustable feet from both sides.
- Unscrew and remove the bottom hinge pin, turn the bracket over, and replace it.
- Refit the bracket fitting the bottom hinge pin. Replace both adjustable feet.
- Remove aid-closers from the bottom of the upper and lower doors. Take new aid closers from the accessory bag and install them on the left side.
- Detach the fridge and freezer door gaskets and then attach them after rotating.
- Install the lower door, adjust, and fix the middle hinge onto the cabinet.
Safety information
In the interest of your safety and to ensure the correct use, before
installing and first using the appliance, read this user manual carefully,
including its hints and warnings. To avoid unnecessary mistakes and accidents,
it is important to ensure that all people using the appliance are thoroughly
familiar with its operation and safety features. Save these instructions and
make sure that they remain with the appliance if it is moved or sold so that
everyone using it through its life will be properly informed on appliance use
and safety.
For the safety of life and property keep the precautions of these user’s instructions as the manufacturer is not responsible for damages caused by omission.
Children and vulnerable people’s safety
- This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Children should be supervised to ensure that they do not play with the appliance.
- Cleaning and user maintenance shall not be made by children unless they are aged 8 years and above and supervised.
- Keep all packaging well away from children. There is a risk of suffocation.
- If you are discarding the appliance pull the plug out of the socket, cut the connection cable (as close to the appliance as you can) and remove the door to prevent playing children from suffering electric shock or to close themselves into it.
- If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death trap for a child.
General safety
WARNING! Keep ventilation openings, in the appliance enclosure or the built-in structure, clear of obstruction.
WARNING! Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
WARNING! Do not damage the refrigerant circuit.
WARNING! Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacturer.
WARNING! Do not touch the light bulb if it has been on for a long period of time because it could be very hot.”
- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
- The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless flammable.
- During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged.
- avoid open flames and sources of ignition
- thoroughly ventilate the room in which the appliance is situated
- It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short circuit, fire and/or electric shock.
- This appliance is intended to be used in household and similar applications such as
- staff kitchen areas in shops, offices and other working environments;
- farmhouses and by clients in hotels, motels and other residential-type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.
WARNING! Any electrical components(plug, power cord, compressor etc.) must be replaced by a certified service agent or qualified service personnel.
WARNING! The light bulb supplied with this appliance is a “special use lamp bulb” usable only with the appliance supplied. This “special use lamp” is not usable for domestic lighting.”
- The power cord must not be lengthened.
- Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire.
- Make sure that you can come to the mains plug of the appliance.
- Do not pull the mains cable.
- If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or fire.
- You must not operate the appliance without the lamp.
- This appliance is heavy. Care should be taken when moving it.
- Do not remove nor touch items from the freezer compartment if your hands are damp/wet, as this could cause skin abrasions or frost/freezer burns.
- Avoid prolonged exposure of the appliance to direct sunlight.
Daily use
- Do not put hot on the plastic parts in the appliance.
- Do not place food products directly against the rear wall.
- Frozen food must not be re-frozen once it has been thawed out.”
- Store pre-packed frozen food by the frozen food manufacturer’s instructions.”
- Appliance’s mmanufacturingstorage recommendations should be strictly adhered to. Refer to relevant instructions.
- Do not place carbonated fizzy drinks in the freezer compartment as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance.”
- Ice lollies can cause frost burns if consumed straight from the appliance.”
Care and cleaning
- Before maintenance, switch off the appliance and disconnect the mains plug from the mains socket.
- Do not clean the appliance with metal objects.
- Plastic scraper objects to remove frost from the appliance. Use a
- Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean the drain. If the drain is blocked, water will collect in the bottom of the appliance. 2)
Installation
Important! For electrical connection carefully follow the instructions given in specific paragraphs.
- Unpack the appliance and check if there are damages to it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought it. In that case, retain packing.
- It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back into the compressor.
- Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.
- Wherever possible the spacers of the product should be against a wall to avoid touching or catching warm parts (compressor, con- denser) to prevent possible burn.
- The appliance must not be located close to radiators or cookers.
- Make sure that the mains plug is accessible after the installation of the appliance.
Service
- Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person.
- This product must be serviced by an authorized Service Center, and only genuine spare parts must be used.
Energy saving
- Don’t put hot food in the appliance;
- Don’t pack food close together as this prevents air from circulating;
- Make sure food doesn’t touch the back of the compartments);
- If electricity goes off, don’t open the doors);
- Don’t open the doors) frequently;
- Don’t keep the doors) open for too long time;
- Don’t set the thermostat to exceeding cold temperatures;
- Some accessories, such as drawers, can be removed to get a larger storage volumes and lower energy consumption.
Environment Protection
This appliance does not contain gasses that could damage the ozone layer, in
either its refrigerant circuit or insulation materials. The appliance shall
not be discarded together with the urban refuse and rubbish. The insulation
foam contains flammable gases: the appliance shall be disposed of according to
the appliance regulations to obtain from your local authorities. Avoid
damaging the cooling unit, especially the heat exchanger. The materials used
on this appliance marked by the symbol s are recyclable.
Thermal note product or nus pok in indicates that this should be taken to the appropriate collection point forthe recyclingg of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of the product. For more detailed information about recycling this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
Packaging materials
The materials with the symbol are recyclable. Dispose of the packaging in
suitable collection containers to recycle it.
Disposal of the appliance
- Disconnect the mains plug from the mains socket.
- Cut off the main cable and discard it.
Overview
SpaceRequirement
- Select a location without direct exposure to sunlight;
- Select a location with enough space for the refrigerator doors to open easily;
- Select a location with level (or nearly level) flooring;
- Allow sufficient space to install the refrigerator on a flat surface;
- Allow clearance to the right, left, back and top when installing. This will help reduce power consumption and keep your energy bills lower.
- Keep at least 50a mm gap at two sides and back.
Positioning
Install this appliance at a location where the ambient temperature corresponds
to the climate class indicated on the rating plate of the appliance:
Location
The appliance should be installed well away from sources of heat such as
radiators, boilers, direct sunlight etc. Ensure that air can circulate freely
around the back of the cabinet. To ensure the best performance, if the
appliance is positioned below an overhanging wall unit, the minimum distance
between the top of the cabinet and the wall unit must be at least 100 mm.
Ideally, however, the appliance should not be positioned below overhanging
wall units. Accurate levelling is ensured by one or more adjustable feet at
the base of the cabinet.
Warning! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.
Electrical connection
Before plugging in, ensure that the voltage and frequency shown on the rating
plate correspond to your domestic power supply. The appliance must be earthed.
The power supply cable plug is provided with a contact for this purpose. If
the domestic power supply socket is not earthed, connect the appliance to a
separate earth in compliance with current regulations, consulting a qualified
electrician. The manufacturer declines all responsibility if the above safety
precautions are not observed.
This appliance complies with the E.E.C. Directives.
Door Reversibility
Before reversing the door, please prepare below tools and materials: straight
screwdriver, cross screwdriver, spanner and the components included in the
poly bag:
- Unscrew the top hinge cover and disconnect the connectors of the door switch and harness.
- Unscrew top hinge
- Remove the pin with a screwdriver and fill the hinge bracket. Then refit the pin to the hinge bracket
- Move the door switch from the right hinge cover to the left hinge cover in accessory bag.
- Detach the cover on top of the upper door and move the harness from the right side to the left side, then replace the cover.
- Move the top left cover to the right side
- Take off the upper door, take out the screw from the middle hinge with a cross screwdriver, and then take off the lower door.
- Move the hinge hole covers from the left side to the right side.
- Unscrew the bottom hinge. Then remove the adjustable feet from both sides.
- Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.
- Refit the bracket fitting the bottom hinge pin. Replace both adjustable feet.
- Remove aid closers from the bottom of the upper and lower doors, then take new aid closers from the accessary bag and install them on to left side.
- Detach the Fridge and the Freezer door gaskets and then attach them after rotating.
- Install the lower door, adjust and fix the middle hinge onto the cabinet.
- Replace uthe pper door, please ensure the door aligns with the cabinet to make sure the door gasket is sealed tightly. Then connect the door to the cabinet by a tightly fixed top hinge.
- Connect harnesses from the door and cabinet. Then replace the top hinge cover. Before screwing the cover, connect the terminals of the door switch.
Space Requirement
- Keep enough space for the door open.
- Keep at least a 50mm gap at two sides.
Levelling the unit
To do this adjust the two levelling feet at front of the unit. If the unit is
not level, the doors and magnetic seal alignments will not be covered
properly.
User interface
Using the Control Panel
BUTTON OPERATION
- A. Temperature Control of Fridge Compartment
- B. Temperature Control of Freezer Compartment
- C. Mode / Locking / Unlocking
LED DISPLAY
- The temperature of Fridge Comparment
- Temperature of Freezer Comparment
- ECO Mode
- Holiday Mode
- Super Mode
- Locking / Unlocking
OPERATING CONDITION
- The control panel is 100% lit up for 3 seconds, which operates exactly as per the setting (mode and temperature) before the ppower off The system will be automatically locked 25 seconds after the last button operation. After locking, the light of the panel would be out 2 minutes after the last button operation.
- Both preset temperatures of the fridge compartemnt and freezer compartment would be shown on the display.
DISPLAY
- The panel will be lit up for 2 minutes once the door of the fridge compartment is opened.
- The panel will be lit up by any button operation whereas the light would be out 2 minutes after the last operation.
- Display during normal operation
- Temperature Display of the Fridge Compartment: Indicating the temperature of the current setting.
- Temperature Display of the Freezer Compartment: Indicating the temperature of the current setting.
ILLUSION OF THE BUTTON
Temperature Control of the Fridge Compartment:
This button is workable both in User Defined Mode as well as Super Mode. After
entering the temperature control of the fridge compartment, this button
flashes. By touching the key consecutively, the temperature would change in a
circle of “2°C, 3°C, 4°C, 5°C, 6°C, 7°C, 8°C, after which 5-second flashing
means the selection of temperature is settled.
Temperature Control of the Freezer Compartment
This button is workable both in User Defined Mode as well as Holiday Mode.
After entering the temperature control of the freezer compartment, the button
flashes. By touching the button consecutively, the temperature would change in
a circle from -14°C to -22°C, after which a 5-second flashing means the
selection of temperature is settled.
Mode
By touching this button consecutively, the operation mode of the refrigerator
will change in a circle of “ECO Mode-Holiday Mode-Super Mode-User Defined
Mode. A 5-second flashing means the selection of temperature is settled.
Press Button
- Short beep after pressing the button
- All buttons will only be valid under unlock mode.
Lock / Unlock
- Press the MODE button and hold for 3 seconds to lock the other two buttons, then the LOCK icon will be a lock situation after a beep.
- To unlock, press the MODE button and hold for 3 seconds, then the LOCK icon will be at unlock situation after a beep. In the unlock situation, all buttons are workable.
- If no operation in 25 seconds, the display will be locked automatically. Keep pressing the “MODE” button to unlock the display.
ECO mode
- Press the MODE button to choose ECO mode. After 5 seconds of flash, the ECO icon will keep bright and ECO mode is confirmed.
- In ECO mode, the refrigerator will automatically set the temperature of the fridge compartment at 5°C, and the temperature of the freezer compartment at -18°C. Except MODE button, other buttons will not respond to any press.
- Press the MODE button to exit ECO mode.
Holiday Mode
- Press the MODE button to choose Holiday mode. After 5 seconds of flash, the Holiday mode icon will keep bright and the Holiday mode is confirmed.
- In Holiday mode, the temperature of the fridge will be set at 17°C. The “FRIDGE” button will not respond to any press.
- Press the “MODE” button to exit Holiday mode.
Super mode
Press the MODE button to select Super mode. And it will be confirmed after
5 seconds of a flash of the Super icon. In Super mode, the “FREEZER” button
will not respond to any press.
To exit Super mode,
- Adjust mode by MODE button,
- Or after 50 hours of Super mode, the refrigerator will automatically stop it and enter to previous setting.
Helpful hint:
If you plan to freeze a large number of food at one time, please set Super
mode 24 hours ahead.
Warning:
In Super mode, the refrigerator will work hard. So the noise of the
refrigerator will be slightly higher than normal running.
Door Open Alarm
If the fridge (upper) door keeps open for 60 seconds, the periodical alarm
will arise until the door is closed.
First use
Cleaning the interior
Before using the appliance for the first time, wash the interior and all
internal accessories with lukewarm water and some neutral soap to remove the
typical smell of a brand-new product, then dry thoroughly.
Important! Do not use detergents or abrasive powders, as these will damage the finish.
Daily use
Freezing fresh food
- The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time.
- Place the fresh food to be frozen in the bottom compartment.
- The maximum amount of food that can be frozen in 24 hours is specified on the rating plate.
- The freezing process lasts 24 hours: during this period do not add other food to be frozen.
Storing frozen food
When first starting up or after a period out of use. Before putting the
product in the compartment let the appliance run for at least 2 hours on the
higher settings.
Important!
In the event of accidental defrosting, for example the power has been off for
longer than the value shown in the technical characteristics chart under
“rising time”, the defrosted food must be consumed quickly or cooked
immediately and then re-frozen (after cooked).
Thawing
Deep-frozen or frozen food, before being used, can be thawed in the freezer
compartment or at room temperature, depending on the time available for this
operation. Small pieces may even be cooked still frozen, directly from the
freezer. In this case, cooking will take longer.
Helpful hints and tips
Hints for freezing
To help you make the most of the freezing process, here are some important
hints:
- the maximum quantity of food that can be frozen in 24 hrs. is shown on the rating plate;
- the freezing process takes 24 hours. No further food to be frozen should be added during this period;
- only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
- prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
- wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
- do not allow fresh, unfrozen food to touch food that is already frozen, thus avoiding a rise in temperature of the latter;
- lean foods store better and longer than fatty ones; salt reduces the storage life of food;
- water ices,iceconsumed immediately after removal from the freezer compartment, can cause the skin to be freeze burnt;
- it is advisable to show the freezing date on each pack to enable you remto oval from the freezer compartment, which can cause the skin to be freeze burnt;
- it is advisable to show the freezing date on each pack to enable you to keep a tab of the storage time.
Hints for storage of frozen food
To obtain the best performance from this appliance, you should:
- make sure that the commercially frozen foodstuffs are adequately stored by the retailer;
- be sure that frozen foodstuffs are transferred from the food store to the freezer in the shortest possible time; do not open the door frequently or leave it open longer than necessary.
Once defrosted, food deteriorates rapidly and cannot be refrozen. Do not exceed the storage period indicated by the food manufacturer.
Hints for fresh food refrigeration
To obtain the best performance:
- Do not store warm food or evaporating liquids in the refrigerator
- Do cover or wrap the food, particularly if it has a strong flavour
Hints for refrigeration
Useful hints:
- Make (all types): wrap in polythene bags and place on the glass shelves above the vegetable drawer.
- For safety, store in this way for only one or two days at the most.
- Cooked foods, cold dishes, etc…: these should be covered and may be placed on any shelf.
- Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
- butter and cheese: these should be placed in special airtight containers or wrapped in aluminium foil or polythene bags to exclude as much air as possible.
- Milk bottle: these should have a cap and should be stored in the balconies on the door.
- Bananas, potatoes, onions and garlic, if not packed, must not be kept in the fridge.
Fresh Zone Temperature Control
- The temperature of the fresh can be adjusted according to the type of storage food.
- Push the knob upward from the bottom, temperature in the fresh zone will be gradually decreased.
- When the knob is placed at the “CRISPER” position, the fresh zone can be functioned as a crisper zone and maintain the appropriate temperature and humidity for fruits and vegetables.
- When the knob is placed at the ” CHILLER” position, it is suitable for short-term storage of fish or other fresh food. The food will keep fresh but not frozen which makes it the best choice for storing fresh food.
- Tips: When you choose the ” CHILLER” function, it is recommended to set the refrigerator temperature below 4°C. and preserve lead time of no more than 3 days, to keep the best freshness.
Cleaning
For hygienic reasons, the appliance interior, including interior accessories,
should be cleaned regularly.
Caution!
The appliance may not be connected to the mains during cleaning. The danger of
electrical shock! Before cleaning switch the appliance off and remove the plug
from the mains, or switch off or turn out the circuit breaker or fuse. Never
clean the appliance with a steam cleaner. Moisture could accumulate in
electrical components, and the anger of electrical shock! Hot vapours can lead
to damage to plastic parts. The appliance must be dry before it is placed back
into service.
Important!
Ethereal oils and organic solvents can attack plastic parts, e.g. lemon juice
or juice from orange peel, butyric acid, and and cleanser that contains acetic
acid.
- Do not allow such substances to come into contact with the appliance parts.
- Do not use any abrasive cleaners
- Remove the food from the freezer. Store them in a cool place, well covered.
- Switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker of the fuse.
- Clean the appliance and the interior accessories with a cloth and lukewarm water. After cleaning wipe with fresh water and rub dry.
- After everything dry place the noliance back into service.
Replace the lamp
The internal light is an LED type. To replace the lamp, please contact a
qualified technician.
Troubleshooting
Compion Befosetubles otto, dishes hot the oversupply Only a qualified electrician of
Important!
There are some sounds during normal use (compressor, refrigerant circulation).
| Problem | Possible cause | Solution |
|---|
The appliance does not work
| The mains plug is not plugged in or is loose| Insert mains plug.
The fuse has blown or is defective| Check the fuse, and replace it if
necessary.
Socket is defective| Mains malfunctions are to be corrected by an electrician.
The appliance freezes or cools too much| The temperature is set too cold
or the appliance runs at Super
modes.
|
Turn the temperature regulator to a warmer setting temporarily.
The food is not frozen enough.
| Temperature is not properly adjusted.| Please look in the initial
Temperature Setting section.
The door was open for an extended period.| Open the door only as long as
necessary.
A large quantity of warm food was placed in the appliance within the last 24
hours.| Turn the temperature regulation to a colder setting temporarily.
The appliance is near a heat source.| Please look in the installation location
section.
Heavy build-up of frost on the door seal.
|
The door seal is not airtight.
| Carefully warm the leaking sections of
the door seal with a hair dryer (in a cool setting). At the same time shape the
warmed door seal by hand such that it sits correctly.
Unusual noises
| The appliance is not level.| Re-adjust the feet.
The appliance is touching the wall or other objects.| Move the appliance
slightly.
A component, e.g. a pipe, on the rear of the appliance is
touching another part of the appliance or the wall.
|
If necessary, carefully bend the component out of the way.
*The ide panel is hot
|
The condenser is inside the panel.
|
, As normal.
If the malfunction occurs again, contact the Service Center. These data are necessary to help you quickly and correctly. Write the necessary data here, refer to the rating plate.
FAQ’s
Can I install the refrigerator in direct sunlight?
No, it is not recommended to install the refrigerator in direct sunlight.
What is the recommended space requirement for installation?
It is recommended to keep at least a 50mm gap at two sides and the back of the refrigerator.
How do I reverse the door opening direction?
Follow the steps provided in the user manual to reverse the door opening direction.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>