Breezary 27009-BK 18 Inch Black Indoor Downrod Ceiling Fan User Manual

Breezary 27009-BK 18 Inch Black Indoor Downrod Ceiling Fan

Product Information

Specifications:

• Model: 60in
• Weight Capacity: Minimum of 35 lbs (15.9 kg)
• Blade Clearance: Minimum of 7 ft (2.1 m) from the trailing edge of the blades to the floor

Product Usage Instructions

Step 1: Mounting

1. Ensure that the electricity has been turned off at the circuit breaker or fuse box.
2. Securely mount the outlet box and support structure capable of supporting a minimum of 35 lbs (15.9 kg).
3. Use only UL-listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”.
4. Check and retighten all setscrews before installation.
5. Mount the motor housing securely.

Step 2: Mounting Blades to Motor

1. Place the blades on the motor as shown in the figure.
2. Lock the three blades in sequence.
3. Ensure that the downrod and set screws are completely tightened to avoid wobbling and damage to the fan.

Step 3: Install Mounting Bracket
If the fan is installed on a cement top without an outlet box, follow these steps:

1. Use an impact drill to drill two 8mm holes, ensuring that the distance between the two holes is about 100mm.
2. Completely insert the pipe part of the expansion screw into the hole and remove the washer and nut.
3. Place the hanger into the screw head, place the washer, and use a wrench to tighten the nut.

FAQ

• Q: Can I use a solid-state fan speed control device with this fan?
  A: No, using a solid-state fan speed control device will permanently damage the electronic circuitry and is not recommended.

• Q: Should I bend the blade brackets when installing or cleaning the fan?
  A: No, bending the blade brackets can lead to personal injury and damage to the fan. Please avoid bending them.

• Q: How far should the fan be mounted from the floor?
  A: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.

• Q: Can I make changes or modifications to the fan?
  A: No, any changes or modifications not expressly approved by the responsible party could void the user’s authority to operate the equipment.

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be by the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked ” Acceptable for Fan Support of 35 lbs. (15.9 kg) or less.”
4. Do not place objects in the path of the blades.
5. To clean the fixture, turn off the power, wait for it to cool, and wipe the fixture with a clean, soft cloth.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.
7. All set screws must be checked and retightened where necessary before installation.
   • WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuitry.
   • WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the racket: balancing the blades, or cleaning the fan. Do not inser
   • WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support of 35 lbs. (15.9 Kg) or less” and use screws provided with the outlet box.
   • WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring.
   • WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control / switch.
   • CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.
   • CAUTION: Please use carefully when workins around or cleaning the fan to avoid injury or damage of fan.
   • CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.
   • CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.
   • CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Dimension Reference

Parts Included

Hardware Included

Exploded View

Installation Instructions

Step-1 MOUNTING

• Take out fan motor assembly.
• Remove cotter pin and bolt from yoke. (Fig.1a)
• Loosen jam screw in yoke until it is flush with the inside surface. (Fig.1b)
• Obtain downrod, canopy and yoke cover.
• Place downrod inside canopy and yoke cover. (Fig.1c)
• Route wires exiting motor through yoke cover, canopy and downrod.
• insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires. (Fig.1d)
• Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
• Secure downrod in position by tightening jam screws. Slide yoke cover down and it will flush with the motor housing. (Fig.1e)

CAUTION: To ensure the wobble-free operation and to avoid damage to the fan, the downrod and the set crew must be completely tightened.

Step-2 MOUNTING BLADES TO MOTOR

• Install the blades on the motor as shown in the figure.
• Lock the three blades in sequence, Place it on the cardboard box.

Step-3 INSTALL MOUNTING BRACKET
If it is installed on the cement top and dont have outlet box, please use two expansion screw.

• Use an impact drill to drill two Φ8mm holes, Note that the distance between the two holes is about 100mm.

• Completely insert the pipe part of the screw into the hole and remove the washer and nut.

• Place the hanger into the screw head, place the washer, and then use a wrench to tighten the nut.
  CAUTION: To Reduce The Risk of Fire, Electric Shock, Or Personal lnjuy, Mount to UL/CSA Listed Outlet Box Marked Acceptable for Fan Support And Use Mounting Screws Provided With The Outlet Box

• Install J-Hook through centre of outlet box and into the wooden joist.

• Secure mounting bracket and rubber gaskets to metal outlet box.

• Hang the safety cable onto the J-hook.

Step-4 LIGHT KIT
WARNING: BE SURE TO TURN OFF POWER BEFORE INSTALLING

• Remove light kit screws. (Fig.4a)
• Align the light kit hole with hte connecting piece and lock the screw. (Fig.4b)
• Insert the terminal of the light wire into the light source port. (Fig.4c)
• Place Lampshade onto the fan and turn to secure. (Fig.4d)

WARNING: Check all connections, set screws and screws are securely tightened before the next step.

Step-5 ELECTRICAL HOOK-UP

• A. Use wire connectors to connect household supply and receiver according to the diagram and the following steps:
  • Insert the terminals on the controller’s connecting wire properly
  • Connect the green wire from the downrod and mounting bracket to theBare/Green (ground) supply wire.
  • Insert the terminals of the light kit into the terminals of the receiver.
  • Insert the terminals of the Motor into the terminals of the receiver.
  • Connect the Black wire with the Black label to the Black (live) supply wire.
  • Connect the White wire with the White label to the White (neutral) supply wire.
• B. Push all connected wires up into ceiling box.
  • Position the receiver into the mounting bracket as shown direction.
  • When installing the canopy, ensure the antenna is not pressed by the canopy.
  • Ensure to connect all ground wires accordingly.
• C. FUNCTION INSTRUCTION OF EMITTER
  • Learning code and matching mode is used between emitter and receiver.
  • Open battery cover on the hand-held remote and install battery, pair of AAA of emitter(1.5V) that are not included.
  • If the emitter can not control the fan, learning code matching mode is used between emitter and receiver.
  • Turn “ON” the supply power within 10 seconds and press the emitter’s “ ” button for 5 seconds, it can load normally after hearing a long sound “bee”, which means learning successfully and it can works normally.
  • When the emitter cannot control the receiver, please check the battery switch touching normally or not, correct the positive and negative, full or empty of the power.
  • When the emitter cannot control the receiver, please check is there any existence of similar remote-controlled products nearby, then check whether they works, because remote-controlled product with the same frequency will disturb each other.
  • Please take out the battery from the emitter when leaving unused for long time. When installing the fan, the fan ceiling cover don’t press the antenna(or other wire), it is easy to breakdown the wire and is short-circuited.

Step-6 MOUNTING FAN ASSEMBLY

• Place two screws and washers on mounting plate which correspond with slots in canopy. Screw in two turns.

Step-7 ENGAGE HEMISPHERE

• Carefully rotate fan assembly until groove in hemisphere locks over tab of canopy assembly.
• Loosen (do not remove) the two screws on mounting bracket. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket,turn canopy until it locks in place at the narrow section of the key holes.
• Align the holes on the canopy with mounting bracket and secure with the two set of screws until snug.
• WARNING: Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.
• NOTE: When installing fan on sloped ceiling, make sure tab on hanger bracket faces towards the top of the slope. Depending on the slope, a longer downrod may be required to prevent fan bladesfrom hitting the ceiling.

Step-8 Install Canopy Cover

• Push the canopy cover-up, Align the holes with the two screws.
• Rotate clockwise until it engages.

NOTE: You have completed all the installation steps. Check if any steps have been missed and if any excess parts have not been installed.

Troubleshooting Guide

My hase it case resistant colin may be masten regulation out send in displease check this troubleshooting guide.

Balacing Kit

The Balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your Owners Manual under “Attaching The Fan Blades.”

1. Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
2. Turn off the fan and allow it to a come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of blade.
3. Turn the fan on. Note whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
4. Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
5. Remove the clip and install a balancing weight to the top of blade along the center line near the point where the clip was positioned.
6. If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and additional weights.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>