Chenghai LH-X60WF Folding Drone Instruction Manual

Chenghai LH-X60WF Folding Drone

INSTRUCTION MANUAL

Thank you for purchasing our products. In order to use them properly and ensure your safety, please read this instruction manual carefully before using the products, and please keep them in a safe place for future reference.

REMOTE CONTROL FUNCTION KEYS & NAME DESCRIPTION

REMOTE CONTROL BATTERY INSTALLATION

Remove the battery cover from the back of controller(Fig.A)

Replace the battery cover

DRONE LITHIUM BATTERY CHARGING INSTRUCTIONS

Press the drone’s rear battery module and pull the lithium battery module out of the drone battery compartment.(Fig.C) 3.2

Plug the USB charging cable into the USB power socket, and then connect the other end to the charging socket of the Li-ion battery module; when charging, the LED light is red, and when charging is finished, the LED light will automatically turn off, and the charging time is about 90 minutes.(Fig.D)

After charging is complete, insert the lithium battery module into the battery slot as shown below.(Fig.E) Special note: Please fully charge the battery before flying. A Low-pressure warning tip: When the drone enters the low- pressure alarm, the body light will flash slowly. At this time. it indicates that the drone has been exhausted and needs to fly back immediately.

Attention

1. Make sure the voltage of the USB charger fits the local electricity supply.Keep the battery in a cool place to avoid exposure)
2. The Charging plug will overheat if overcharged. Please stop charging immediately as it may cause damage to the battery.
3. Do not leave the battery aside when charging.
4. Do not use other chargers other than the one supplied in consideration of safety.
5. Recharge the battery 30 minutes later after flying, because the battery temperature could be too high when flying and charging immediately could damage the battery. (The drone needs to take out the battery when not in use and store it at 80% to extend battery life)
6. Do not leave the battery in the fire in consideration of safety.
7. Do not short circuit the battery. Do not leave the battery together with tiny medal parts in consideration of safety.

PRE-FLIGHT ENVIRONMENTAL REQUIREMENTS

Please choose an outdoor environment with no rain or snow, wind less than level 4. Please stay away from people, trees, power lines, tall buildings, airports and signal towers. A Special Tips: The flight time is about 6-7 minutes, and the charging time is about 90 minutes.

PREPARATION BEFORE FLIGHT

Drone frequency

1. Install the drone battery and the remote control battery, turn on the drone power switch, and the body lights up and then put it on the level ground.
2. Turn on the remote control power switch, The light on the aircraft body turns steady on, indicating that the remote control is successfully linked.(Important note: the product must be operated in steps, otherwise it is easy to connect and control badly.)

Calibration of gyroscope operation

After the drone and the remote control have successfully matched the frequency, the drone can be corrected, and the throttle lever and the direction control lever are simultaneously hit to the lower right corner. At this time, the indicator light of the drone flashes rapidly, and the indicator light is always on, and all the buttons of the remote controller are released. The calibration is complete. A Special Tips:If the drone takes off and flies, it can also be corrected by correcting the gyroscope.

Drone unlock
Drone needs to unlock before flying, tum the left and right joysticks of remote controller outward simultaneously and then return (Fig.2). At this time, the four propellers are at the same time. Speed rotation indicates successful unlocking. When unlocking is completed, the drone can operate normally.

One key take-off and landing

When the unlocking is completed, press the function button of the remote control (Fig. 3) again, the drone will automatically rise to a height of about 1 meter to keep the altitude flying smoothly; when the button is used for the takeoff landing icon, the drone will automatically land slowly.

A Note :One key landing must land on a horizontal plane, because a fixed- height function landing on a horizontal surface will cause the drone to fly and fv.

A Flight step prompt: frequency(5.1) – gyroscope correction(5.2) – unlock(5.3) – one key take off/one key landing(5.4)

CONTROL METHOD

• When the left joystick (throttle) is pushed upward, the main wind blade speed increases and the drone rises.
• When the left joystick (throttle) is pushed down, the main wind speed slows down and the drone drops.

Special note: The product has a function of air pressure and height, but it does not have a fixed point effect. When it is not controlled in the air, the product will move slightly at the same height in the air.

Viren the drona is boated 9CM above the ground. The Drora is not atia do due to die cranes of the actual current, which is called “ground @foct reaction”, and the height more lower the drone is, he greater the impost

TRIMMING FUNCTION

If the drone does not push the rudder lever during flight and is still spinning or flying in the air, you can use the fine adjustment function to adjust the rudder. The operation is as follows:

SPEED SWITCHING

Speed switching: “Di~” is the low speed mode, “Di-Di~” is the medium speed mode, and “Di-Di-Di” is the high speed mode.(power on default low speed mode)

HEADLESS MODE

Startup and setup In front of the drone when the power is turned on, the default is the front of the headless mode; if the impact or the front of the flight is biased, please restart the drone and adjust to the direction you need to perform the frequency; after the frequency is successful, the machine The head direction is the front of the headless mode. When the headless mode button is pressed (Fig.5), the drone body light flashes and enters the headless mode.

Exit headless mode
Press the headless mode button again (the remote control emits a “Di~”), the body light turns on constantly, and the headless mode is exited.

As shown in the above figure, in the headless mode state, no matter which direction the drone head is turned, the remote control direction lever is pushed forward, and when the drone is turned on, the head moves in the direction of the head.

ONE KEY RETURN

When the drone is flying farther away, the drone can be recalled using the return function. During the flight, long press the home button for 3 seconds to start the Retum. After starting the home, the drone to the start of the frequency of the end of the other side to return, the return process, the right joystick before and after the action or long press the home key 3 seconds. cancel the Return.

ONE KEY EMERGENCY

When the drone collides during flight and cannot be controlled, please use the emergency stop function button to realize the emergency stop. It is not available under normal conditions.

ONE KEY 360° FLIPS

The drone can make a 360° flight through the rocker operation below. In order to perform the tumbling function better, please ensure that the drone is fully charged and maintains a height of about 1.5 meters with the ground. It is best to operate the drone for tumbling during the ascent, so that it is easier to maintain the height after the drone is tumbling. When the battery is low, the roll will show height or roll. Please charge it in time to experience more flying fun.

MAIN BLADE INSTALLATION

Please unscrew the screws to open the two fan blades and the connecting parts as shown in the figure below. Remove the fan blades and replace them. Make sure all propellers are installed in the correct orientation; if the installation is wrong, the aircraft will not be able to fly normally.

PROTECTION RING INSTALLATION

The aircraft is equipped with 4 rotor guardrails. It is recommended that you install guardrails to prevent damage or damage to the rotors. If you need to install or remove guardrails, just press or dial out the corresponding position of the guardrail according to the figure below. A Note: These rotor guardrails are identical and can be mounted on any arm of the aircraft.

COMMON PROBLEM-SOLVING GUIDELINES

NOTES

Please ensure that the battery power is sufficient and the remote distance will be affected when the battery is low.
If the batter power is not enough, it will not fly high enough or take off 16.3 If the drones are broken and deformed, please repair them in time. If the rotors are broken and damaged, they will not fly, or they will cause injury 16.4 Please avoid a crash or a serious collision, which can damage the drone or shorten the life of the Drone.

FCC WARNING

Any Changes expressly or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>