Shantou City Chenghai Jingwei Industrial 866-167 Power Racing 2.4GHz Radio Remote Control Monster Truck Instruction Manual

866-167 168 169

This product MUST be handled with due care We understand high speed is our long pursuit. However, safety is also a regulation to observe. Please operate your vehicle in a spacious area and do not operate it where people are confused. Do not attempt to assemble or disassemble the electronic units, and when it is not in use, you MUST keep them out of children’s reach. This product is fully assembled at the factory. Malfunction and damage that result from misuse and/or abuse will void the warranty. Contrived modification will also void the warranty.

Warning:
Please read and understand the manual before using, assembling, and/or disassembling. This product is not a toy but an authentic model, which is not individually intended for a person under 14 years of age. Only when the adults keep under supervision can the operators under 14 operate this product. Do not attempt to run the vehicle on low battery power. Please charge the battery pack immediately the slow speed is observed. Do not overcharge the battery pack.

OPERATING INSTRUCTIONS OF HIGH-SPEED R/C RACING VEHICLE

This is one model of 4WD offroad highspeed racing vehicle with extremely good off-road performance. From the four-wheel independent suspension design and 4WD Transmission System. every detail is carefully developed and this racing vehicle can be operated under extreme weather or in harsh environments. Even you can still enjoy the interesting fun of water splashing on a rainy day or drive it in various humid environments
When you receive your favorite vehicle, first of all, please remove the “R” button from the vehicle shell and then remove the vehicle shell. Insert the battery plug into the plug of the RF drive board. Press the red ON/OFF key, this time the LED light will be flashing. Load correctly 2PCS AA batteries into the transmitter as per the correct a+/- polarity. Pull to “ON’ position, and the LED light on the transmitter will turn from flashing into eternal bright -ON” . which represents it has been successfully decoded and you can operate this R/C vehicle. Due to the high speed, please do operate it in the safe environment.
For the sake of safety. we designed the first backward as the braking function and designed the blocking protection function for the driving motor and designed the anti-collision buffer function for the steering gear, the low- voltage reminding function, and the forced sleep function.
During the process of racing forward or backward, when the motor load is detected to be too large(including jammed running), the vehicle will stop the current output in order to protect the motor from being damaged. When the current operation is stopped, it will automatically exit the state of protection.
When racing forward, the first backward will start the braking function in order to prevent the vehicle from hitting obstacles. Only when the vehicle races backward for the second time will it race backward.
When the battery power is lower than 30%. the LED light will be flashing for 10 seconds to remind you of insufficient battery power.
When the battery power is lower than 20%. the LED light will keep flashing while switching off the forward and backward function and only the left and right steering function is kept so as to prevent the battery from excessive discharge and thus protect the battery.
When the battery power is lower than 10%, the vehicle will be forced to enter into the sleep state and should be charged before switching on If the transmitter has successfully finished decoding with the vehicle, however, the LED light of the transmitter still keeps flashing, it represents battery power in the transmitter is insufficient and AA batteries need to be replaced.

GENERAL INFORMATION:

Time to make an authentic hobbyist out of yourself, this 1/16TH SCALE 4WD vehicle can necessitate it. Ready to run out of the box. Small as it is. this vehicle does never compromise itself on performance in contrast with any other R/C vehicle of big size. Energetic power and swift acceleration award you worthwhile admire from all people around you. This vehicle outgrows the fear of running at high speed, but safe and modest driving is strongly recommended. Much agile and responsive to great fun. Get it fast and unleash it on the ground.

• Stylish PVC vehicle Body.
• Front & Rear Independent Suspension.
• Speed: up to 60km/h
• 2.4GHZ Radio System.
• 7.4V, 1200mAH Li-ion battery pack, and USB charger included.
• This R/C vehicle is not a toy but an authentic hobby-grade product
• It is not intended for users under 14 years of age unless closely supervised by an adult.
• Never operate this vehicle with low battery power
• Please stop running this vehicle and charge the battery pack when the standstill is observed. Standstill indicates that the battery is flat\
• Never overcharge the battery pack and never charge the battery pack unattended.
• Abuse and incorrect operation will void the warranty.

BATTERY SAFETY INFORMATION

The included Li-ion battery pack is not waterproof. Do not expose it to any source of heat and humidity. Do not operate your vehicle where it could come in contact with salty water ( ocean water or water on salt-covered roads ), contaminated or polluted water You are required to charge the battery pack before first-time use.

NOTE: Please disconnect the battery pack with your vehicle when not in use.
Do not attempt to run your vehicle immediately after it comes to standstill.
Failure to do so will discharge and damage the battery pack.
Charge the battery pack immediately the slow speed is observed.

GETTING FAMILIAR WITH THE CHASSIS

• The image is presented only for reference, which may vary from your received model.

PRECAUTIONS FOR 2.4GHZ RADIO CONTROLLER

IMPORTANT INFORMATION:
Switch on the radio controller, and then the ESC/Recenter on the vehicle.
The binding process 6 autOrnatgally performed in the system
Never flip the Trigger or the Steering Wheel the moment you are switching on the radio controller.
Failure to do so will cause the radio system to record the incorrect signals

You are ONLY permitted to handle the Trigger and the Steering Whet: alter your vehicle is boded with the radio controller
Do NOT flip the trigger or the steering wheel at the time you switch on the radio controller.

SAFETY INFORMATION-1

We want users to enjoy our RC vehicles and to operate them with care Failure to operate your vehicle in a safe and responsible manner may result in injury to yourself or others or damage to property around you

• Read and understand all instructions carefully before use and assembly/disassembly.
• Do not run your vehicle on public roads or any area where you may encounter pedestrians or vehicle POP<
• Do not operate in a congested area or in crowds.
• Do not operate your vehicle with an obstructed line of what night, or near water.
• Your vehicle is radio controlled and radio waves are subject to interference. Radio interference can cause loss of control of your vehicle
• ‘Take care not to cut yourself %Mule using took to adjust or upgrade your vehicle
• Since the model contains many small pans. keep out of reach of children while assembling and/or disassembling
• ‘If your vehicle becomes stuck release the throttle. then retrieve it by hand.
• Do not continue to apply the throttle or you may damage the motor and/or the ESC/receiver unit

SAFETY INFORMATION-2

• Your vehicle is designed to run on uneven or rough terrain. However dust. sand. water and carpet fibers can lodge in the working parts of your vehicles and can damage your vehicle if not removed promptly. We do not warranty your vehicle from damage due to outside elements including sand dirt or water The users are responsible for the maintenance and safe operation of this vehicle.
• This product is not a toy It is not suitable for users under 14 years 01 unless they are supervised by adults.
• Never attempt to re-assemble any electronic components – These have been carefully calibrated at the factory
• ‘Only use manufactured parts to upgrade your vehicle .11 you perform drive train upgrade. replace the entire system ( Such as motor. ESC/receiver unit and the like ) so that all components are properly matched. Any malfunction incurred by custom modification will void your warranty
• Before driving your vehicle, please read this manual completely and examine your vehicle and radio control for any defects
• For better performance. some adjustments may be necessary.
• The vehicle requires one battery pack ( included in the vehicle or in the packaging I. Make sure the vehicle’s battens have a sufficient charge before droving or possible loss of control may result The radio controller requires two AA sue batteries ( not included in the packaging).
• Always remove batteries from the vehicle and the radio controller when not in use
• Please operate your vehicle in a spacious area. Never operate your vehicle in crowded streets
• This product is fully assembled at the factory. We do not take any responsibility for damage and/or accidents that occur as the retain of custom modifications and/or Incorrect operation.

RECEIVER

Press and hold for 23 seconds to switch on or off.

1.  Power switch
2. Servo Slot
3. Aux. Slot(for LED light if it contains LED)
4. For Motor Plugs
5. Antenna
6. Power cable

for 2S(7.4V) battery only Always erect the antenna for best performance.

INSTALLING THE BATTERIES TO THE RADIO CONTROLLER

The battery cover is located on the bottom of the radio control Open the battery cover as shown in the photos, install three AA sue batteries into the battery compartment, and replace the battery cover Battery Precautions:

1. Do not mix new and old batteries
2. Use batteries of the same brand
3. Always remove batteries when not rn use
4. Before Laing your vehicle. make sure the radio Controller is of enough battery power low battery power will lead to the loss of control col your vehicle

GETTING FAMILIAR WITH THE RADIO CONTROLLER

1 . Steering Trim
2 . Steering D/R
3. Steering Reverse
4. Speed Control (limiter)|  5. Throttle Reverse
6 . ON/OFF Power Switch
7. Steering Wheel
8. Throttle Trigger
9. Battery Compartment
---|---

STARTING RUNNING

CHECK STEERING PERFORMANCE

1. Place the steering wheel at the Center to enable the vehicle to run area ghtly in line.
   NOTE: flipping to the steering w4se0 is occasionally mode< It largely depends On the conditions of the terrains on which the vehicle runs

2. Turn the steering wheel to the left. and the vehicle turns left

3. Turn the steering wheel to the right. and the vehicle turns night

*CHECK TRIGGER RESPONSE

A Put the throttle trigger backward. the vehdeveill leeward Adjusting the angle of the throttle trigger can adjust the forward speed of the vehicle During the vehicle’s going forward. July push the trigger leeward to stop
B To stop running your vehicle, release the trigger to Neutral
C. Loosen the trigger to make it return to the neutral position when brake Push the throttle trigger forward. the vehicle will backward Adjust the forward angle of the throttle trigger to adjust the backward speed of the vehicle

TO TUNE THE STEERING TRIMMER

STEERING TRIMMER
Tune the steering benne( to enable the front wheels to be aligned Under this case, the steering Center Point is set Mu can tune this switch to obtain your desired Left/Right steering angles
SPEED SWITCH
SPEED LEVEL SETTING From level 0 to 10. you Can set your dewed speed
STEERING REVERSE SWITCH

If the vehicle turns eight when you steer left, Rip ‘Steering Reverse switch. If the vehicle turns left when you steer right flip the ‘Steering Reverse’ switch.
THROTTLE REVERSE SWITCH
If the vehicle goes back when you pull the trigger, flip this switch If the vehicle goes forwards when you push the treggerfhp this switch

STEERING DUAL RATE(D/R)

How to use the steering dual rate(Steering D/R) knob? The steering dual rate know allows you to change the amount of steering servo travel compared to the amount of physical movement of the steering wheel The amount that you Increase the steering dual rate is proportional to how much you move the steering dual rate knob.ln addition. adjustments can be made whole you are droving So you can fine•tune the steering during a race, etc. By increasing the steering dual rate (turn the knob clockwise). you can make the steering servo travel more which might prevent your whirl* from pushing during turns. 8y reducing the steering dual rate (turn the kricbcountesktinwice). you make the steering servo travel less which might reduce the amount of turn-on in the conkers.

STOPPING RUNNING

1. MIRROR THE RECEIVER ON YOUR VEHICLE

2. TURN Off THE RADIO CONTROLLER

3.  Switch off the ESC/Receiver Press and hold the button for 2.3 seconds to switch off.

4. Switch off the Transmitter. Slide the Power Switch to the -OFF” position.

5. Disconnect and remove the battery pack from the vehicle when not in use. fug), charge the battery pack before storing it.

6. Make sure there are no damaged parts before storing them. Check gears for wear. debris or broken/slopping teeth. Check for loose screws in the chassis. And make sure the wheels are firmly installed before use Clean the vehicle with a soft and dry cloth before storing it. Store the vehicle in a clean and dry place out of children’s reach. Do NOT expose the vehicle to any source of heat and water

CHARGING THE BATTERY PACK

The battery pack should be removed from the vehicle when it is intended to be charged. Remove the clip to open the battery cover as shown in the photo. and then remove the battery pack Connects the battery pack with the USB charger as shownPlug on the t/S13 charger to the computer to charge the battery pack The red indicator on the USB flashes. which indicates that it is charging the battery pack The green indicator is solid after the battery pack is fully charged.

PRACTICE FOR OPERATION

Once you become conformable driving the vets le, perform driving practice on the tracks as shown in the figure Keep practicing until you feel comfortable with the steering, throttle, and brake at low speed Once you are feeling comfortable try to operate, ng on another track. When you have mastered the basics you will be able to drive at higher speeds in a more controlled way.

SPECIAL ATTENTION!

When the car is playing on the beach, the sand may enter the motor through the heat dissipation hole of the motor, which causes the car can’t move forward or backward. At this time, the car should be made to stand upside down, turn both rear wheels at the same time, clean the sand inside the motor, and then operate the car again.

MAINTENANCE

We warmly recommend that you check and maintain the vehicle after use. The items in the list below will facilitate you, and follow the list to maintain the performance of the vehicle.

• Disconnect and remove the batteries from the vehicle and the radio controller
• Inspect the vehicle for any obvious damage.
• Check the gears for wear, debris, or broken / slipping teeth. |
• Check the wheels and tighten the wheel screws/nuts properly.
• Check for loose screws in the chassis.
• Check the wiring for frayed or damaged wires and/or connectors.
• Check the steering servo which will wear out over time and require replacement
• Check all batteries in the vehicle and in the radio controller. Charge or replace them.
• Keep the chassis clean and free of sand dust and moisture.
• Make sure there is no grass ( or something ) getting twisted in the drivetrain and clean them.
• Clean the motor if necessary ( Never attempt to re-assemble the motor
• Clean the vehicle body with a soft lint-free cloth.
• Store the vehicle in a clean and dry place out of children’s reach. Do not expose the vehicle to any source of heat and water

TROUBLESHOOTING

A. TM vehicle does not work at all:

1. Check to ensure that the radio controller and vehicle are switched on.
2. Check the battery power, and replace it with the new batteries if necessary.
3. Check if there are damaged parts/wires/connectors. repair or replace if necessary 4) Vehicle battery is flat. Charge the battery pack.

B. The vehicle runs slowly:

1. The vehicle battery is flat. Charge the battery pack.
2. Check if the vehicle is properly geared and if no dirty or stripped gears are found. and make sure the reliable gear mesh for motor pinion and the spur gear.
3. Check if there is something troubling with the moving pans. and clean them immediately.

C. The throttle works but not the steering:

1. Check if the servo feels jammed, and try centering it gently if it is the case.
2.  Check if the servo link is loose or if the servo breaks. Repair or replace with a new one if possible.

D. It steers, but the throttle is uncontrollable:

1. Check if there are damaged parts in the entire drivetrain.
2. Check the batteries both for the radio controller and the vehicle.

E. The vehicle runs noisily:

1. Check gear mesh between the spur gear and motor pinion.
2. Check if there are stripped and/or dirty gears.
3. Check if there are some parts getting damaged in the entire drivetrain.
   F. You do not pull or push the trigger, but the vehicle goes forwards/backward: Please set the Throttle Trim to Throttle Center Point.
   G. The vehicle is found one direction’s steering travel is not same to the other Please set the Steering Trim to Steering Center point.
   H. Not able to charge the batteries: Check both the charger and the batteries if they are damaged. Check if the batteries are over-discharged. Replace with the new batteries

FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Pan 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used In accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation.
if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and 00, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• In the separation between the equipment and Waiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

866-167

866-158

866-169

Documents / Resources

| Shantou City Chenghai Jingwei Industrial 866-167 Power Racing 2.4GHz Radio Remote Control Monster Truck [pdf] Instruction Manual
866-1012141816, 8661012141816, 2APVY866-1012141816, 2APVY8661012141816, 866-167, 866-168, 866-169, Power Racing 2.4GHz Radio Remote Control Monster Truck, 866-167 Power Racing 2.4GHz Radio Remote Control Monster Truck
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>