ApeStellar AS T626 Matte Black Electronic Keypad Deadbolt Instruction Manual

June 16, 2024
ApeStellar

ApeStellar AS T626 Matte Black Electronic Keypad Deadbolt Instruction Manual

**** Complete all the programming steps in the programming mode within 10 seconds Do not press keypad until keypad stops illuminating

Creating Administrator Code

Administrator Code
Administrator Code
Administrator Code

Adding a User Code

Adding a User Code
Adding a User Code
Adding a User Code

Unlocking Door with User Code

Unlocking Door with User Code

  PROGRAMMING RECORD

My Codes: Date Created

  • Programming: Code (6 digits)
  • User Code 02 : (4-8 digits)
  • User Code 03 : (4-8 digits) / User Code 04
  • User Code 05 : (4-8 digits)
  • User Code 06 : (4-8 digits)
  • User Code 07: (4-8 digits)
  • User Code 09 : (4-8 digits)
  • User Code 10:   (4-8 digits)
  • User Code 11: (4-8 digits)
  • User Code 12: (4-8 digits)
  • User Code 13: (4-8 digits)
  • User Code 14 : (4-8 digits)
  • User Code 15 : (4-8 digits)
  • User Code 16 : (4-8 digits)
  • User Code 17: (4-8 digits)
  • User Code 18: (4-8 digits)

Deleting a User Code

Deleting a User Code
Deleting a User Code
Deleting a User Code

Deleting All User Codes

User CodesUser
CodesUser
Codes
Additional Programming Functions

Programming Symbols

Lock/Clear
Unlock/Programming
Administrator Code

Automatic Lock Function

SET OR CANCEL AUTO LOCK

You can set the lock to automatically close after each time the lock is opened. Time value range-5-900 seconds, enter the following:

Set Auto Lock:
Coding Icon

Hear 1 beep and Light Indicator illuminates green.

To cancel Auto Lock set the time to 00, enter the following:

Cancel Time Value Auto Lock:
Coding Icon

Hear 1 beep and Light Indicator illuminates green.

TEMPORARILY DISABLE:

While in Auto-Lock mode, unlock door using within 10 seconds you must turn the locking knob by hand to the locked position, wait more than 2 seconds then turn the locking knob back to the unlock position. The Auto-Lock mode is now disabled.

RESTORE :

To restore the Auto-Lock function, turn wait more than 2 seconds or press the the locking knob by hand to the locked position, Lock button on the keypad.

Vacation Mode

With Vacation Mode enabled, the system enters into low-power consumption mode During this mode, all buttons and functions will be disabled until they are re-enabled

ENABLE :
Coding Icon

Once the door is locked then vacation mode will be engaged and all buttons and functions will be disabled

DISABLE :

To disable the Vacation Mode, you must press and hold for more than 3 seconds, then Input followed by to unlock the door Vacation Mode is now disabled.

NOTE: If you only press the for more than 3 seconds but do not input the system will remain in Vacation Mode.

Secure Lock-out period

Warning sounds and LED flashes red after 4 incorrect code attempts. Keypad shuts down for 60 seconds.

Additional Programming Functions

SOUND ON AND OFF

You can “mute” or turn the sound on on your lock by entering the following. (Factory setting is sound on).
Coding Icon

Sound Off (1)-Light Indicator illuminates green.
Sound On (2)-Hear 1 beep and Light Indicator illuminates green.

Restore Factory Settings

To reset the lock to the original factory settings including the Programming Code and all User Codes follow these steps:

  1. Remove one battery for 10 seconds.
  2. Reinsert the battery and wait for a long and short beep
  3. Press 3 times within 3 seconds.
  4. The lock will beep and the light indicator will turn green.

Low Battery Warning

Beeps and LED flashes red 7 times. Replace with good quality alkaline batteries.
Note: Removing batteries does not erase active Administrator or User Codes.

Consumer Friendly Message Guide

Unlock / Valid programming: 1 long beep and LED illuminates green
Lock: 2 short beeps and LED illuminates red
Invalid Programming: 2 short beeps and LED flashes red twice
Low Voltage: Short beeps and LED flashes red seven times
Super Low Voltage: 4 short beeps and LED flashes red four times
4 Incorrect code entry attempts: 2 short beeps and LED illuminates red each

attempt
Power on:| 1 long beep with red lingt on, 1 short beep with green light on. After direction detection, 1 long beep with red+green light on.
Chip Rese :| 1 long beep and 1 short beep and LED illuminates green (may occur several times or once in a while)
Lock Error| 3 long beeps LED flashes red three times
Repeat operation after Lock Error| 2 short beeps three times LED flashes red six times

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals