California PCH Driver Jump Hour Sunset Orange Instruction Manual
- June 16, 2024
- CALIFORNIA
Table of Contents
California PCH Driver Jump Hour Sunset Orange
Product Information
Specifications
- Water Resistance: 3 ATM
- Battery Type: 3V Coin Cell (CR2016)
- Warranty: Two years
Product Usage Instructions
Setting the Time
- Set the Minute Disc:
- Press and hold the C key for about 3 seconds.
- The minute hand dial will move in a clockwise direction.
- Continue to press and hold the C key until the minute hand reaches the selected local time.
- Release the key. The minute hand has been set.
- Set the Hour Disc:
- Press and hold the A key for 3 seconds.
- The hour hand will move in the direction of the hour hand.
- Continue to press and hold the A key until the hour hand reaches the selected local time.
- Release the key. The hour hand has been completely set.
- Backlight Function:
- Press and release the B button.
- The light will be on for 4 seconds and then turn off automatically.
Factory Reset
- Press and hold the B button for about 10 seconds.
- All the discs will return to the default position.
Adjusting the Discs after Factory Reset
- If the pointers are not in the factory setting position, press the B button again for about 10 seconds.
- The hour disc will vibrate as a signal to adjust it back to the factory setting using the A or C button.
- After adjusting the hour disc, press the B button again.
- The minute disc will vibrate as a signal to adjust it back to the factory setting using the A or C button.
- After completing the above steps, you can proceed to set the local time by following the “Setting the Time” steps.
Water Resistance
- This watch has a water resistance rating of 3 ATM, making it splash-resistant. It is not intended for any prolonged exposure to water.
- Do not expose your watch to high-temperature water (i.e. hot tubs/showers) as this will void the warranty.
Battery Type
This watch uses a 3V Coin Cell battery type: CR2016.
Frequently Asked Questions (FAQ)
Q: What should I do if the hour and minute discs are out of alignment?
A: If you find that the hour and minute discs are out of alignment after adjustment, please complete a Factory Reset and then repeat the steps for Setting the Minute and Hour Discs.
OVERVIEW
TWO YEAR WARRANTY
- California Watch Co. (CA) gladly offers a limited warranty covering defects in materials and manufacturing for two (2) years after the original purchase date from an authorized CA retailer.
- This warranty does not cover batteries, cases, crystals, crowns, pushers, straps, or any changes that occur during use and not from manufacturing or assembly.
- This warranty is considered void if you open your case back, push the buttons underwater, or expose your watch to moisture beyond the recommended water resistance rating.
- Proof of purchase is required for all warranty claims, so please save a copy of your receipt.
- CA reserves the right to not accept a warranty claim if a watch has evidence of excessive wear or misuse.
- CA reserves the right to repair or replace any watch returned for service at our option.
SETTING THE TIME
Set the Minute Disc
- Press and hold the C key for about 3 seconds, then the ” minute hand” dial will move in a clockwise direction, please continue to press and hold the C key until the ” minute hand” reaches the selected local time, then release the key (the ” minute hand” has been set).
Set the Hour Disc
- Press and hold the ” A” key for 3 seconds and the ” hour hand” will move in the direction of the ” hour hand”, please continue to press and hold the ” A” key until the ” hour hand” reaches the selected local time and then release the key (” Hour hand” has been completed setting).
Backlight Function
- Please release the button immediately after pressing the ” B” button, the light will be on for 4 seconds and then turn off automatically.
- The operators of the above A” and C” keys must use sharp hardware tools to adjust them.
- If you find that the hr/min discs are out of alignment after the adjustment, please complete “Factory Reset “, and then repeat “Setting the Minute and Hour Discs
BATTERY TYPE
3V Coin Cell: CR2016
FACTORY RESET
- Press and hold the ” B” keys for about 10 seconds, and all the discs will return to the default position.
Make sure the discs show the following factory standards:
- Hour disc” is at 12 o’clock
- Minute disc ” is 00 minutes
- If it is on the right point, wait 5 seconds for the watch to return to normal time mode.
- If the above pointer is not in the factory setting position, press the ” B” button again for about 10 seconds.
- The ” hour disc” will generate a vibrating signal, at this moment you can use the ” A” button or the ” C” button to adjust back to the factory setting.
- After the ” hour disc” is adjusted, press the B button again, the ” minute disc” will vibrate as the signal, and then you can use the ” A” button or the ” C” button to adjust back to the factory square.
- After completing the above action, you can return to the “Setting the Time” steps to set the local time.
WATER RESISTANCE
- 3 ATM Splash Resistant.
- Not intended for any prolonged exposure to water.
- Do not expose your watch to high-temperature water (i.e. hot tubs/showers) as this will void the warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>