ANALOG DEVICES LTC3311-1 2MHz Automotive Low EMI Buck Regulator User Manual

June 16, 2024
Analog Devices

LTC3311-1 2MHz Automotive Low EMI Buck Regulator
User Manual

LTC3311-1 2MHz Automotive Low EMI Buck Regulator

ANALOG DEVICES LTC3311 1 2MHz Automotive Low EMI Buck
Regulator

DEMO MANUAL D C 3113A
LTC 3 311-1
3.3V to 1V at 12.5A, 2MHz Automotive
Low EMI Buck Regulator

DESCRIPTION

Demonstration Circuit 3113A features the LT C ® 3311-1, fixed 1V, 12.5A synchronous step-down Silent Switcher ® operating as a 2MHz, 3V to 3.6V input, 1V/12.5A output buck regulator. The LTC3311-1 supports fixed 1V output voltage with operating frequencies from 500kHz up to 5MHz. The LTC3311-1 is a compact, ultralow emission, high efficiency, and high speed synchronous monolithic step-down switching regulator. The LTC3311-1 has Active Voltage Positioning (AVP) where the output voltage is dependent on load current. At light load, the output voltage is regulated above the nominal value. At full load, the output voltage is regulated below the nominal value. The DC load regulation is adjusted to improve transient performance and reduce required output capacitance.
DC3113A is set up to run in forced continuous mode with a 2MHz switching frequency but can be configured to run at different switching frequencies, or in pulse-skipping mode. The LTC3311-1 oscillator can also synchronize to an external clock using MODE/SYNC turret, with the DC3113A default setup. Figure 7 shows the efficiency and power loss of the DC3113A with a 3.3V input in both operation modes.
The DC3113A is optimized for a 4A to 12A, 8A/µs load step transient. A fast load step transient circuit is placed on the back of the demo board to measure the load step response of the converter.
The DC3113A also has an EMI filter to reduce conducted EMI. This EMI filter can be included by applying the input voltage at the VIN EMI terminal. The EMI performance of the board is shown in the EMI TEST RESULTS section.
The red lines in the EMI performance graphs illustrate the CISPR25 Class 5 peak limits for the conducted and radiated emission tests.
The LTC3311-1 data sheet gives a complete description of the part and its application information. The data sheet must be read in conjunction with this demo manual. The LTC3311-1 is assembled in a 3mm × 3mm LQFN package with exposed pads for low thermal resistance. The layout recommendations for low EMI operation and maximum thermal performance are available in the data sheet section Low EMI PCB Layout.

Design files for this circuit board are available.
All registered trademarks and trademarks are the property of their respective owners.

PERFORMANCE SUMMARY

Specifications are at TA = 25°C

SYMBOL| PARAMETER| CONDITIONS| MIN| TYP| MAX| UNITS
---|---|---|---|---|---|---
VIN/VIN EMI| DC3113A Input Voltage Range| | 3.0| | 3.6| V
VOUT_TYP| DC3113A Typical Output Voltage| IOUT = 8A| 0.990| 1.000| 1.010| V
VOUT_NO_LOAD| DC3113A Output Voltage with No Load| IOUT = 0A| 1.005| 1.016| 1.027| V
VOUT_FULL_LOAD| DC3113A Output Voltage with Full Load| IOUT = 12.5A| 0.980| 0.991| 1.001| V
VAVP| VOUT Active Voltage Positioning| |

2

| mV/A
IOUT| DC3113A Output Current| |

12.5

| A
fSW| Switching Frequency| | 1.8| 2| 2.2| MHz
EFF| Efficiency| VIN = 3.3V, IOUT = 5A| 90| %

BOARD PHOTO

Part marking is either ink mark or laser mark

QUICK START PROCEDURE

Refer to Figure 2 for the proper measurement equipment setup and follow the procedure below:
NOTE: For accurate VIN, VOUT and efficiency measurements, measure VIN at the VIN SNSE and GND SNSN turrets, and measure VOUT at the VOUT SNSE and GND SNSE turrets as illustrated as VM1 and VM2 in Figure 2. When measuring the input or output ripple, care must be taken to avoid a long ground lead on the oscilloscope probe.

  1. Set the JP1 Jumper to the HI position.
  2. With power off, connect the input power supply to VIN and GND. If the input EMI filter is desired, connect the input power supply to VIN EMI and GND.
  3. Set power supply PS1 current limit to 10A. Set the electronic load LD1 to CC mode and 0A current. Slowly increase PS1 to 1V. If PS1 output current reads less than 20mA, increase PS1 to 3.3V. Verify that VM1 reads 3.3V and VM2 reads around 764mV. Check VM1, VM2, VM3, PS1 output current and LD1 input current. Connect an oscilloscope voltage probe as shown in Figure 3 or Figure 4. Set Channel to AC-coupled, voltage scale to 20mV and time base to 10µs. Check VOUT ripple voltage. Verify that PGOOD voltage is above  3V.
  4. Increase the load by 1A intervals up to 12.5A and observe the voltage output regulation, ripple voltage, and the voltage on the SSTT turret. Calculate Die temperature using the formula below:
  5. If pulse-skipping mode is desired, set PS1 to 0V. Install a 0Ω resistor in the R5 location and remove R3. Repeat steps 1 through 4. In step 4, observe that the switching waveform is now in pulse-skipping mode at light load.
  6. Optional: To change the frequency, remove R4 and R5, if installed. Install the desired RT resistor in the R6 location. Note that the MODE/SYNC pin should have high impedance to GND and VIN. Size the inductor, output capacitors and compensation components to provide the desired inductor ripple and a stable output. Refer to the LTC3311-1 data sheet and LTPowerCAD ® for more information on choosing the required components.
  7. To test the transient response with a base load, add the desired resistor to produce a minimum load between VOUT and I_STEP turrets (RL shown on Figure 2). Note that the total load resistance will be RL plus R10 (10mΩ). Adjust a signal generator with a 10ms period, 10% duty cycle and an amplitude from 1V to 2V to start.
  8. Measure the I_STEP voltage to observe the current, VI_STEP/10mΩ. Adjust the amplitude of the pulse to provide the desired transient. Connect signal generator SG1 between SG_INPUT and GND turrets. Adjust the rising and falling edge of the pulse to provide the desired ramp rate. Figure 8 shows a load step from 4A to 12A. Refer to the following equations:
  9. When done, turn off SG1, PS1 and Load. Remove all the connections to the demo board.

TEST SETUP

THEORY OF OPERATION

Introduction to the DC3113A
The DC3113A demonstration circuit features the LTC3311-1, a low voltage synchronous step-down Silent Switcher. The LTC3311-1 is a monolithic, constant frequency, current mode step-down DC/DC converter. An oscillator turns on the internal top power switch at the beginning of each clock cycle. Current in the inductor then increases until the top switch comparator trips and turnoff the top power switch. The peak inductor current, at which the top switch turns off, is controlled by the voltage on the ITH node. The error amplifier servos the ITH node by comparing the voltage on the internal VFB node with an internal 500mV reference. When the load current increases, it causes a reduction in the feedback voltage relative to the reference, leading the error amplifier to raise the ITH voltage until the average inductor current matches the new load current. When the top switch turns off, the synchronous bottom power switch turns on until the NeXT clock cycle begins. In pulse-skipping mode, the bottom switch also turns off when inductor current falls to zero. If overload conditions result in excessive current flowing through the bottom switch, the next clock cycle will be delayed until the switch current returns to a safe level.
If the EN pin is low, the LTC3311-1 is in shutdown state with low quiescent current. When the EN pin is above its threshold, the switching regulator will be enabled.
The MODE/SYNC pin synchronizes the switching frequency to an external clock. It can be a clock output for multi-phase operation. It also sets the regulator operation modes. The operation modes are either forced continuous or pulse- skipping. See the LTC3311-1 data sheet for more detailed  information.
The maximum allowable operating frequency is influenced by the minimum on time of the top switch, the ratio of VOUT to VIN and the inductance of the output inductor. The maximum allowable operating frequency may be calculated  in the formula below.

Select an operating switching frequency below fSW(MAX). It is desired to obtain an inductor current of 30% of the maximum LTC3311-1 operating load, 12.5A. Use the formulas below to calculate the inductor value to obtain a 30% (3A)  inductor ripple for the operating frequency.ANALOG DEVICES LTC3311 1
2MHz Automotive Low EMI Buck Regulator - icon3

When determining the compensation components, C10, C11 and R8, controlling the loop stability and transient response are the two main considerations. The LTC3311-1 has been designed to operate at a high bandwidth for fast transient response capabilities. This reduces required output capacitance to meet the desired transient voltage range. The mid-band gain of the loop increases with R8 and the bandwidth of the loop increases with decreasing C11. C10 along with R8  provides a high frequency pole to reduce the high frequency gain.
Loop stability is generally measured using the Bode Plot method of plotting loop gain in dB and phase shift in degrees. The 0dB crossover frequency should be less than 1/6 of the operating frequency to reduce the effects of added phase  shift of the modulator. The control loop phase margin goal should be 45° or greater and a gain margin goal of 8dB or greater.

TYPICAL PERFORMANCE CHARACTERISTICS

ANALOG DEVICES LTC3311 1 2MHz Automotive Low EMI Buck Regulator -
TYPICALANALOG DEVICES
LTC3311 1 2MHz Automotive Low EMI Buck Regulator -
TYPICAL1 EMI TEST RESULTSANALOG DEVICES LTC3311 1 2MHz Automotive Low EMI Buck Regulator -
RESULTSANALOG DEVICES
LTC3311 1 2MHz Automotive Low EMI Buck Regulator -
RESULTS1

PARTS LIST

ITEM| QTY| REFERENCE| PART DESCRIPTION| MANUFACTURER/PART NUMBER
---|---|---|---|---
Required Circuit Components
1| 2| C2, C3| CAP, 22p F, X7S, 6.3V, 20%, 0805| TDK, C2012X7S0J226M125AC
2| 3| C4, C12, C20| CAP, 0.1 pF, X7S, 16V, 10%, 0201| MURATA, GRM033C71 C1 04KE14D
3| 5| C5, C6, C21-C23| CAP, 47p F, X7S, 6.3V, 20%, 1206| TDK, C3216X7S0J476M160AC
4| 1| C9| CAP, 0.033pF, X7R, 25V, 10%, 0402| KEMET, C0402 C333K3RACTU
5| 1| C10| CAP., 6.8pF, COG/NPO, 50V, ±0.5pF, 0402| AVX, 04025A6R8DAT2A
6| 1| C11| CAR, 330pF, X7R, 50V, 10%, 0402, AEC-0200| TDK, CGA2B2X7R1H331K050BA
7| 1| C19| CAP, 2.2pF, X7S, 10V,10%, 0402, AEC-0200| MURATA, GRT155C71A225KE13D
8| 1| C24| CAP, 0.1 pF, X7R, 16V, 10%, 0402, AEC-0200| MURATA, GCM155R71C104KA55D
9| 1| L1| IND., 0.08pH, PWR, 20%, 21.4A, 1.8m52, 4mm x 4mm, AEC-0200| COILCRAFT XEL4020-800MEC
10| 1| R8| RES., 10k, 1%, 1/16W, 0402, AEC-0200| VISHAY, CRCW040210K0FKED
11| 1| U1| IC, LOW VOLTAGE SYNCH STEPDOWN REG, LOFN-18, PRELIM-PART NOT FOR PRODUCTION| ADI APPROVED SUPPLIER, LTC3311JV-10BF
Additional Demo Board Circuit Components
1| 2| C1, C18| CAP., 470pF, TANT, POSCAP 6.3V, 20%, 7343, 10ma TCF| PANASONIC, 6TCF470MAH
2| 2| C7, C15| CAP, 0.1 pF, X7R, 10V, 10%, 0402, AEC-0200| MURATA, GCM155R71A1 04KA55D
3| 1| C8| CAP, 22p F, X7S, 6.3V, 20%, 0805| TDK, C2012X7S0J226M125AC
4| 4| C13, C14, C16, C17| CAP, 10p F, X7S, 6.3V, 20%, 0603| TDK, C1608X7S0J106M080AC
5| 2| C25, C26| CAP, 0.22pF, X7R, 6.3V, 20%, 0603| JOHANSON DIELECTRICS, 6R3X14W224MV4
6| 1| C27| CAP, 2.2pF, X7S, 10y, 10%, 0402, AEC-0200| MURATA, GRT155C71A225KE13D
7| 1| L2| IND., 1000 AT 100MHz, FERRITE BEAD, 25%, 8A, 6m0, 1812| WURTH ELEKTRONIK, 74279226101
8| 1| 1| XSTR., MOSFET, N-CHAN, 25V, 100A, TDSON-8 pin| INFINEON, BSCO1ONE2LSI
9| 1| R1| RES., 1M, 1%, 1/16W, 0402, AEC-0200| STACKPOLE ELECTRONICS, INC., RMCF0402FT1M00
10| 1| R2| RES., 249k, 1%, 1/16W, 0402, AEC-0200| NIC, NRCO4F2493TRF
11| 2| R3, R9| RES., 100k, 5%, 1/16W, 0402, AEC-0200| NIC, NRC04.1104TRF
12| 1| R4| RES., OD, 1/16W, 0402, AEC-0200| NIC, NRCO4ZOTRF
13| 1| R7| RES., 200, 1%, 1/16W, 0402, AEC-0200| NIC, NRCO4F2OROTRF
14| 1| R10| RES., 0.020, 1%, 10W, 2818, HP METAL, SENSE, AEC-0200| VISHAY, WSHP2818R0200FEA
15| 1| R11| RES., 10k, 5%, 1/16W, 0402, AEC-0200| NIC, NRC04.1103TRF
16| 0| TP1| CONN., U.FL, RECEPT ST SMD, 0Hz TO 66Hz 500| HIROSE ELECTRIC, U.FL-R-SMT 1(10)
Hardware: For Demo Board Only
1| 12| El-E3, E5, E12, E14-E17, E20-E22| TEST POINT TURRET, 0.064″ MTG. HOLE, PCB 0.062′ THK| MILL-MAX, 2308-2-00-80-00-00-07-0
2| 5| E4, El, El 0, El 3, El 8| TEST POINT TURRET 0.094″ MTG. HOLE, PCB 0.062″ THK| MILL-MAX, 2501-2-00-80-00-00-07-0
3| 5| E6, E8, E9, Ell, E19| CONN., BANANA JACK, FEMALE, THT NON- INSULATED, SWAGE, 0.218″| KEYSTONE, 575-4
4| 1| JP1| CONN., HEIR, MALE, 1 x 3, 2mm, VERT, ST, THT| WURTH ELEKTRONIK, 62000311121
5| 4| MP1-MP4| STANDOFF NYLON, SNAP-ON, 0.50″| KEYSTONE, 8833
6| 1| XJP1| CONN., SHUNT FEMALE, 2-POS, 2mm| WURTH ELEKTRONIK, 60800213421

SCHEMATIC DIAGRAM

ANALOG DEVICES LTC3311 1 2MHz Automotive Low EMI Buck Regulator -
SCHEMATIC

REVISION HISTORY

REV DATE DESCRIPTION PAGE NUMBER
A 3/23 Updated Parts List Replaced Schematic Diagram 8 9

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from  its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non- exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

www.analog.com
ANALOG DEVICES, INC. 2023
Downloaded from Arrow.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Analog Devices User Manuals

Related Manuals