DS18 CA-X3BASS-P Maverick X3 12 Under Seat Water Proof Subwoofer Enclosure Installation Guide
- June 16, 2024
- DS18
Table of Contents
OWNER’S MANUAL
CA-X3BASS -P
12″ UNDER SEAT ENCLOSURE WITH
PSW12.4D SHALLOW SUBWOOFER
FOR CAN-AM X3 PASSENGER SIDE SPECIALLY
DESIGNED FOR
CAN-AM X3
12″ UNDER SEAT ENCLOSURE WITH PSW12.4D SHALLOW SUBWOOFER FOR CAN-AM X3 PASSENGER SIDE
FEATURES
- Especially designed for the Passenger side under seat location
- High Output Down-firing 12” Shallow Subwoofer
- Sealed Waterproof under seat enclosure design
- Easy to install design using factory bolt locations
- Integrated Sound Damping to mitigate vibration and potential rattle
- Plug and play Wiring design for easier installation and maintenance
- Does not interfere with seat position or height
- Subwoofer DS18 PSW12.4D Included.
- Aftermarket Subwoofer amplifier required (NXL-X1000.1D Recommended) not included.
INSTALLATION
Step 1: Release the lower seat belt strap from the harness by feeding it
back through the tension assembly. This will allow you to feed the shoulder
straps through the hole at the top of the seat. Step 2: Remove two (2)
13mm bolts and nuts at the front of the seat frame. Step 3: Access the
rear 18mm nuts using a socket with extension either by aligning the holes in
the seat base over the nuts or by sliding the seat fully forward and reaching
behind. Step 4: With the seat free, disconnect the seat belt sensor and
speed sensor cables from the seat assembly. Step 5: Once disconnected, lift
the seat out of the vehicle and set aside. Remove the 10mm M6 bolt holding the
brake line clamp in place on the seat frame.
Step 6: Remove the cable clamp from the brake line. Step 7: Wrap the
brake line with the strip of adhesive backed foam tape included in the box.
Note: This step is to prevent the brake line from rattling against the
enclosure under high bass output and any chaffing due to movement of the brake
line while the vehicle is in motion. Step 8: Tilt the front of the
enclosure down and slide it under the forward crossbar as you set it in place
onto the floor of the vehicle tucking the brake line into the pre-molded slot
in the bottom of the enclosure. Step 9: Taking the long bar bracket
included, align the slotted holes with the threaded insets on the top rear of
the enclosure. The two large holes at either end should slide over the
threaded seat mounting posts. Loosely install three (3) T-40 Torx screws into
the bracket. Step 10: Align the threaded inserts at the front corners of
the enclosure with the holes in the bottom of the seat brackets and insert two
(2). Once all fasteners are in place, tighten to secure the enclosure. T-40
Torx screws.
Route the subwoofer cable to the desired connection point. Note: If installing
as part of a kit, the subwoofer plug will connect to the main harness
supplied. If not installing as part of a kit, the plug will need to be removed
and additional speaker wire added. With your wire routed and system tested,
reinstall the seat in the reverse order as removed.
Note: In the event of floor pan rattle, included in the subwoofer kit are
a self-tapping drill bit and bolts to allow you to bolt the floor pan directly
to the frame of the vehicle.
SPECIFICATIONS
Speaker Type / Size ………………………………………………………….. 12” / 304.8mm
Total Impedance …………………………………………………………………………………………….. 2 Ohm
Total RMS Power Handling ……………………………………………………..600W
Total MAX Power Handling ………………………………………………….. 1200W
Sensitivity ………………………………………………………………………………… 88 dB
Frequency Response …………………………………………………………….. 20Hz-600Hz
Recommended Lo Pass Crossover………………………………. 80Hz
SPEAKER SPECIFICATIONS
Voice Coil Diameter ………………………………………………………….. 3”/76.2mm
Voice Coil Former Material ………………………………………….. Aluminum
Winding Material ……………………………………………………………………………………. Cooper
Cone Material ………………………………… Water Resistant PPI
Surround Material ………………………………………………………….. Rubber
Basket Material …………………………………………………………………………… Steel
Magnet Material ……………………………………………………………………………… Ferrite
Magnet Weight ………………………………………………………………………………………………… 68 Oz
BOX SPECIFICATIONS
Box Type ……………………………………………………………………………………………………. Sealed
Box Material …………………………………………………. Polyethylene (PE)
Finish Material ……………………………………………………………………………… Black
MEASUREMENTS
WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without
notice.
Images may or may not included optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov
FOR MORE INFORMATION PLEASE VISIT DS18.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>