Clarke GWL700R Garage Worklight Instruction Manual
- June 16, 2024
- Clarke
Table of Contents
Clarke GWL700R Garage Worklight
Product Information
Technical Specifications
- Model: GWL700R
- Part Number: 4003541
- Operating Voltages: 5V (light), 230V (charger)
- LED Wattage Consumption: 10W total
- LED Replaceable: No
- Rechargeable Lithium Battery Pack: 2 x 3.7V / 5200mAh
- Charger Output: 5V DC, 2A
- Lighting Source: 2 x lamps
- Light Output (Luminous Flux): Single light: 350 Lumens, Two lights: 700 Lumens
- Colour Temperature (Rendering): 6000-6800K
- Ingress Protection (IP Rating): IP20
- Battery Charging Time: 5-6 hours
- Approximate Run Time: 7 Hours at 50% power, 5 Hours at 100% power
- Rated Lamp Lifetime: 30,000 hours
- Efficiency: 70 Lm/W
- Operating Temperatures: 0 to +45°C
- Dimensions: 780 x 70 x 70mm
- Weight: 1.4Kg
Safety Instructions
- ALWAYS check for damage before using the worklight. Inspect the power cable and plug for damage. Any damage should be properly repaired or the part replaced. Consult your local CLARKE dealer.
- ALWAYS ensure that the voltage marked on the charger matches the power supply to be used.
- NEVER use this lamp in a bathroom or in the vicinity of a swimming pool.
- NEVER cover the lamp.
- NEVER pull the cable to remove the charger plug from the power supply.
- DO NOT look directly into the worklight when it is switched on.
- Keep the worklight out of the reach of children.
- Charge the worklight in a dry indoor location. DO NOT immerse in water or any other liquid.
- ALWAYS fully charge before first use.
- DO NOT turn on the light when charging.
- DO NOT leave the worklight on charge for more than 24 hours.
- DO NOT disassemble the worklight as there are no user changeable parts.
- This worklight utilises a rechargeable Lithium-ion battery that can rupture, ignite, and cause serious injury if being used improperly.
- DO NOT put batteries and the worklight in the fire or high temperature.
- DO NOT puncture or damage the batteries.
- DO NOT immerse or expose the worklight to water.
- DO NOT dispose of the worklight in a fire or water.
Warning Symbols
- Indoor use
- Harmful to aquatic life
- Pacemaker hazard (due to magnet)
- Not suitable for use by children
Environmental Recycling Policy
Please refer to the environmental recycling policy provided by CLARKE for
information on how to properly recycle the worklight.
Guarantee
This worklight is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase. This guarantee is invalid if the worklight is
found to have been abused or tampered with in any way, or not used for its
intended purpose. Faulty goods should be returned to their place of purchase,
no worklight can be returned to us without prior permission. This guarantee
does not affect your statutory rights.
FAQ
-
Q: Can I replace the LED?
A: No, the LED is not replaceable. -
Q: Can I charge the worklight while it is on?
A: No, do not turn on the light when charging. -
Q: Can I leave the worklight on charge for more than 24 hours?
A: No, do not leave the worklight on charge for more than 24 hours. -
Q: Can I disassemble the worklight to replace parts?
A: No, there are no user changeable parts. Do not disassemble the worklight. -
Q: Can I immerse the worklight in water?
A: No, do not immerse or expose the worklight to water.
GARAGE WORKLIGHT
- MODEL NO: GWL700R
- PART N O : 4003541
USER INSTRUCTIONS
INTRODUCTION
Thank you for purchasing this CLARKE worklight. Before attempting to use this worklight, please read this manual thoroughly and follow the instructions carefully.
CONTENTS
- Lamp unit
- 100-240V Charger with USB port
- Micro USB to USB charging cable
TECHNICAL SPECIFICATIONS
Model | GWL700R |
---|---|
Operating voltages | 5V(light), 230V(charger) |
LED Wattage consumption | 10W total |
LED replaceable | No |
Rechargable Lithium battery pack | 2 x 3.7V / 5200mAh |
Charger output | 5V DC, 2A |
Lighting source | 2 x lamps |
Light output (luminous flux) | Single light 350-/ two lights 700 Lumen |
Colour temperature (rendering) | 6000-6800K |
Ingress Protection (IP rating) | IP20 |
Battery charging time | 5-6 hours |
Approximate Run Time | Power @ 50% |
Power @ 100% | 5 Hours |
Rated lamp lifetime | 30,000 hours |
Efficiency | 70 Lm/W |
Operating temperatures | 0 to +45oC |
Dimensions | 780 x 70 x 70mm |
Weight | 1.4Kg |
SAFETY INSTRUCTIONS
- ALWAYS check for damage before using the worklight. Inspect the power cable and plug for damage. Any damage should be properly repaired or the part replaced. Consult your local CLARKE dealer.
- ALWAYS ensure that the voltage marked on the charger matches the power supply to be used.
- NEVER use this lamp in a bathroom or in the vicinity of a swimming pool.
- NEVER cover the lamp.
- NEVER pull the cable to remove the charger plug from the power supply.
- DO NOT look directly into the worklight when it is switched on.
- Keep the worklight out of the reach of children.
- Charge the worklight in a dry indoor location. DO NOT immerse in water or any other liquid.
- ALWAYS fully charge before first use.
- DO NOT turn on the light when charging.
- DO NOT leave the worklight on charge for more than 24 hours.
- DO NOT disassemble the worklight as there are no user changeable parts.
- This worklight utilizes a rechargeable Lithium-ion battery that can rupture, ignite and cause serious injury if being used improperly.
- DO NOT put batteries and the worklight in the fire or high temperature.
- DO NOT puncture or damage the batteries.
- DO NOT immerse or expose the worklight to water.
- DO NOT dispose of the worklight in a fire or water.
THE FOLLOWING WARNING SYMBOLS ARE FOUND ON THE PRODUCT
- Indoor use
- Harmful to aquatic life
- Pacemaker hazard (due to magnet)
- Not suitable for use by children
ENVIRONMENTAL RECYCLING POLICY
- Through purchase of this worklight, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.
- In effect, this means that this worklight must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and
- Electronic Equipment (WEEE) at a recognised disposal facility.
- The light source contained in this worklight has a life expectancy of approximately 30000 hours after which the worklight should be disposed of in an environmentally responsible way.
- The Lithium Ion battery falls under the Waste Batteries and Accumulators Regulations 2009 and should be disposed of in a controlled manner.
GUARANTEE
- This worklight is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
- This guarantee is invalid if the worklight is found to have been abused or tampered with in any way, or not used for its intended purpose.
- Faulty goods should be returned to their place of purchase, no worklight can be returned to us without prior permission.
- This guarantee does not effect your statutory rights.
CHARGING THE WORKLIGHT
IMPORTANT: Charge the worklight after each use or when the battery indicator light shows low.
- Before charging, make sure the work light is turned off.
- Connect the micro USB end of the charging cable to the micro USB port on the worklight the USB port on the wall charger.
- Plug the AC charger into a live AC outlet.
- The green LEDs will illuminate to indicate battery status. Charging will typically take 5-6 hours. When the battery is fully charged all four LEDs will be lit. When fully charged, unplug the charger from the AC outlet and then from the work light.
- Charge the battery every 3 months if the worklight is not in regular use to ensure the longevity of the battery unit. Failure to do this will reduce the battery’s capacity and may void the warranty.
OPERATION
- Charge the internal battery before use.
- Press the power button to ensure there is enough power before use. If low battery power or no power, continue to charge the worklight.
- 1x press – turns on one light
- 2x presses– turns on two lights
- 3x presses – turns all the light off
- The position of each individual light may be rotated for more precise positioning. Tilt the mainbody tothe desired position.
- As the batteries become drained the status LEDs will change from green to red.
- When mounting the worklight to a steel surface ensure both the magnets are i n contact with the steel surface. i
COMPONENT PARTS
1 | EVA foam | 13 | LED base | 25 | Lens |
---|---|---|---|---|---|
2 | Magnet | 14 | Battery support | 26 | LED module-upper |
3 | Screw | 15 | Screw | 27 | Housing-right |
4 | Nut | 16 | Screw | 28 | Housing connector |
5 | Metal plate | 17 | Screw | 29 | Housing -left |
6 | Nut | 18 | Lamp base connector | 30 | USB housing |
7 | Bolt | 19 | Screw | 31 | PCBA |
8 | Hinge | 20 | LED module support | 32 | USB rubber |
9 | Screw | 21 | Li-ion battery | 33 | Switch cap |
10 | Aluminium body | 22 | LED module base | 34 | Switch cap support |
11 | Handle housing | 23 | COB | 35 | Screw |
12 | Lamp base | 24 | Reflector | 36 | Screw |
A SELECTION FROM THE VAST RANGE OF
- PARTS & SERVICE: 0208 988 7400
- Parts Enquiries Parts@clarkeinternational.com
- Servicing & Technical Enquiries Service@clarkeinternational.com
- SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
- Clarke INTERNATIONAL Hemnall Street, Epping, Essex CM16 4LG www.clarkeinternational.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>