SKOV A S 411827 Mounting Set Air Inlet 3 User Guide
- June 16, 2024
- SKOV A S
Table of Contents
Mounting Set Air Inlet 3
411827
Mounting Guide
411827 Mounting set DA 75, 3
The individual pulleys and wheels must not be loaded with more than 150 kg.
1.1 Wall inlets and DA 75 winch motor • direct pull • 2 sides • 1 row
1.2 Wall inlets and DA 75 winch motor • 1:2 • 2 sides • 1 row
1.3 Wall inlets and DA 75 winch motor • 1:4 • 2 sides • 1 row
1.4 Ceiling inlets and DA 75 winch motor • direct pull • 2 sides • 1 row
1.5 Ceiling inlets and DA 75 winch motor • 1:2 • 2 sides • 1 row
1.6 Wall inlets and DA 174 winch motor • direct pull • 2 sides • 1 row
1.7 Winding of winch motor
The wires must be wound on to the wire wheel in order to obtain the correct
pulling or slacking length.
When you are going to wind a winch motor, it must always be in the fully
closed position. The figure above shows where to measure to get rough values
in the scheme. Please note that min. 3 mm should be free to the outer
periphery. The figure also shows the definition of number of wire windings.
Following tables show the rough relation between load, the number of wire
windings and the tensile or slacking lengths.
1000 N equal 98 kg.
DA 75A-1
| Number of wire windings | Tensile length [mm] | Slack length [mm] |
|---|---|---|
| 1 | 237 | – |
| 2 | 260 | 232 |
| 3 | 284 | 256 |
| 4 | 307 | 279 |
| 5 | 331 | 303 |
| 6 | 354 | 326 |
| 7 | 377 | 349 |
| 8 | 401 | 373 |
| 9 | 424 | 396 |
| 10 | 447 | 419 |
| 11 | 471 | 443 |
| 12 | 494 | 466 |
| 13 | 517 | 489 |
| 14 | 541 | – |
DA 75A-3
| Number of wire windings | Tensile length [mm] | Slack length [mm] |
|---|---|---|
| 1 | 502 | – |
| 2 | 549 | – |
| 3 | 596 | 484 |
| 4 | 642 | 530 |
| 5 | 689 | 577 |
| 6 | 736 | 624 |
| 7 | 783 | 670 |
| 8 | 829 | 717 |
| 9 | 876 | 764 |
| 10 | 923 | 811 |
| 11 | 969 | 857 |
| 12 | 1016 | 904 |
| 13 | 1063 | 951 |
| 14 | – | – |
DA 75A-6
| Number of wire windings | Tensile length [mm] | Slack length [mm] |
|---|---|---|
| 1 | 1117 | – |
| 2 | 1210 | – |
| 3 | 1303 | – |
| 4 | 1397 | – |
| 5 | 1490 | – |
| 6 | 1584 | 1135 |
| 7 | 1677 | 1229 |
| 8 | 1771 | 1322 |
| 9 | 1864 | 1416 |
| 10 | 1958 | 1509 |
| 11 | 2051 | 1603 |
| 12 | – | 1696 |
| 13 | – | 1789 |
| 14 | – | – |
DA 75A-12
| Number of wire windings | Tensile length [mm] | Slack length [mm] |
|---|---|---|
| 1 | 2810 | – |
| 2 | 3025 | – |
| 3 | 3245 | – |
| 4 | 3460 | – |
| 10 | – | 2815 |
| 11 | – | 3020 |
| 12 | – | 3250 |
| 13 | – | 3480 |
SKOV A/S • Hedelund 4 • Glyngøre • DK-7870 Roslev
Tel. +45 72 17 55 55 • www.skov.com • E-mail:
skov@skov.dk
604245 • 2023-10-11 • en-US • Made in Denmark
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>