oxbot Cat Fountain with Wireless Pump User Guide
- June 16, 2024
- oxbot
Table of Contents
oxbot Cat Fountain with Wireless Pump
Thank you for purchasing a Oxbot Cat Water Fountain. To reduce the risk of injury, and to extend the life of your product, please read and observe all information in this manual prior to and while using this product. Please save this manual for future reference.
SAFETY INSTRUCTIONS
- Although this is a low Wattage item, an electric shock/electrocution risk is present if your pet chews through the power cord, exposing the wires. Always inspect the cord before use and do not allow pets to chew on it.
- Please choose DC SV-1A adapters in line with relevant national and regional standards to avoid possible damage or safety hazards.
- Place the product horizontally on a stable surface so it cannot tip over. Tipping over may result in damage, malfunction, or water leakage.
- Do not clean any part of this product in dishwasher.
- To move this product or keep it idle for an extended time, please unplug the power cord.
- Children should not handle this device without close adult supervision.
- Check the water level in the fountain daily.
- Do not repair the product without the guidance of professionals to avoid any possible injuries. In the event of a performance issue, please contact our customer service department for assistance.
- When the LED light is solid red, the fountain islow or out of water, replenish water soon ,No light during normal operation.
- To avoid possible electrical shock, this appliance is for indoor household use only.
- Set up the appliance on an even, stable, clean, non-slip, dry and fireproof surface in an open area.
- Do not wash the filter with soapy water. Soap residue will remain in the filter and may cause injury to your pet. Replace filter as needed.
PACKING LIST
UPPER COVER ASSEMBLY
SPECIFICATION PARAMETERS
Product Name | Pet Water Fountain |
---|---|
Product Model | CYD002 |
Dimension | 288.5166125mm |
Rated Voltage/Current | SV / 1A |
Rated Power | SW |
Capacity | 84.5 oz (2.5 L) |
Net Weight | 1.8 lb (0.8 kg) |
Material | ABS+PP+Stainless Steel |
Place of Origin | Guangdong, China |
MAIN FUNCTIONS
- FOUNTAIN STYLE : Upward flow enriches and oxygenates the water.
- WATER LEVEL SENSOR : The built-in water level sensor identifies the water level, and the red light comes on when the water level is low. When the water is used up, the pump automatically turns off.
- FILTRATION SYSTEM: Carbon activated filter cleans, purifies and removes debris and odors for better tasting, healthier water for your pet.
- ULTRA-SILENT PUMP : Create a peaceful environment with low-voltage pump. It operates quietly and has a service life of over 20,000 hours
- SAFE: Upgraded non-inductive electrical design, safe against electric shock.
- CAPACITY: Fountain holds up to 84.5 oz (2.5 L) of water.
OPERATION INSTRUCTIONS
Please follow the steps below before first use.
- Please prepare the filter by soaking it in 41-113° F (5 – 45°C) clean water for about 5 minutes before installation. Discard the water.
- It’s normal for the water used to initially soak the filter to turn yellow or be colorless. The water is not drinkable.
- Rinse the tray and tank with clean water. * No parts of this product are dishwasher safe. Hand wash only.
- Fill clean water into the tank.
- Keep the water amount within the specified capacity of 84.5 oz (2.5 L).
- Range of water temperature: 41-113 ° F (5 – 45 °C) Place the filter upwards into the filter cap, keeping it horizontally in alignment with the groove.
- Insert the outlet pipe and the USB pump into the bottom of the upper cover securely.
- Put the upper cover assembly onto the water tank.
- Place the water fountain on flat ground and power on to run.
Add water
- Remove the entire upper tray assembly as shown belaw.
- Fill with clean water. Do not exceed the maximum fill line.
Connect to power supply
Connect DC wire ta the adapter and plug inta the socket.
CLEAN THE USB PUMP
- Cleaning the pump can extend the service life. It’s recommended to clean the pump every 1-2 months ta avoid bad circulation, poor water quality and increased noise due to blockage.
- Please disassemble the pump and wash it using clean water and a brush, following the steps shown below.
- Step 1 : Remove the pump cover.
- Step 2 : Remove the filter cover.
- Step 3 : Remove the Impeller.
- Step 4 : Clean the parts with the cleaning kit provided.
REPLACE THE FILTER
- The filter should be replaced if the water is cloudy, approximately every 2-4 weeks. It’s recommended to replace the filter every two weeks when shared by multiple pets.
WARRANTY
WARRANTY EXCLUSIONS
- Damage caused by force majeure factors such as fire, lightning, rainstorm, earthquake as examples.
- Damage caused by human error or animals.
- Damage caused by failure to abide by the user manual before assembly, use, disassembly and repair.
- Color fading, wear and tear during normal use.
FAQs
What should I do before installing the filter?
- Soak the filter in a clean container for 5 mins before use.
- Rinse the filter thoroughly for 30 seconds.
Note : We recommend changing the filter once every 2-4 weeks.
For your pet’s health and safety, please search ‘OXBOT’ on Amazon to buy the official filters.
How to use the cat fountain properly?
- For your pet’s health and a longer pump service life, we recommend cleaning the Water Tank, Tray, Foam Filter and Pump at least once a week.
- lf you have multiple pets, please clean the fountain and change the filter more often.
How can I maintain the pump to extend its lifespan?
- For a longer pump service life, we recommend cleaning the pump at least once a week.
- lf the water fountain makes more noise, please check if the water level reaches the minimum level and if the impeller is covered by the scale.
Why is the product lit up in red?
This is a humanized feature we added. After the water level drops to a certain position, it will remind us to change/add water to their pets.
Why does the water pump not produce water after adding water?
The product with water shortage power-off function, the water volume down to a certain position after the red light to remind the need to add water, if you add water directly to the top of the container, the water pump will enter the air after the power off, the pump needs to wait 3-5 minutes to discharge the air. So we recommend pouring out the remaining water and filling the bottom of the container with water.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>