Carson JC-1000 SkySeeker 40 100x60mm Refractor Telescope Instruction Manual

: June 16, 2024
: Carson

Table of Contents

JC-1000 SkySeeker 40 100x60mm Refractor Telescope
SPECIFICATIONS
VISUAL GUIDE
INSTRUCTIONS FOR USE
FINDERSCOPE ADJUSTMENT
ALTITUDE-AZIMUTH MOUNT
GENERAL CONSIDERATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JC-1000 SkySeeker 40
100x60mm Refractor Telescope
Instruction Manual

JC-1000 SkySeeker 40 100x60mm Refractor Telescope

$Carson JC-1000 SkySeeker 40 100x60mm Refractor Telescope - fig1$

A. Micro adjustable Altitude control	J. Lens
B. Focusing wheel	K. Yoke locking screw
C. Focusing tube	L. Adjustment locking nut
D. Angle prism	M. Yoke bracket
E. Eyepiece	N. Azimuth lock
F. Finderscope bracket	O. Tripod head
G. Finderscope	P. Accessory tray
H. Main telescope body	Q. Tripod leg
I. Sunshade	R. Plastic tipped feet

SPECIFICATIONS

Focal length: 800 mm
Diameter of Objective Lens: 60 mm
1.25 inch eyepieces: H8mm & H20mm
Finder scope: 5x24mm
Magniﬁcation: 40X when using the H20mm eyepiece
100X when using the H8mm eyepiece

VISUAL GUIDE

$Carson JC-1000 SkySeeker 40 100x60mm Refractor Telescope - VISUAL GUIDE$

INSTRUCTIONS FOR USE

Extend the legs (Q) as shown in Fig. 1, and lock them at the desired height using the wing nut (1) supplied.
Connect the three legs to the tripod head (O) using the wing nut and the bolt (2), proceeding as shown in Fig. 2a.
Then attach the accessory tray (P) to the ﬂanges of the tripod legs using the adjustment nuts and bolts supplied (see Fig. 3).
Once all of the bolts have been tightened down fully, the telescope’s main body can be attached to the tripod head yoke (M). Proceed as shown in Fig. 2b: mount the telescope’s main body (H) in the yoke (M) and adjust it using the large locking screw (K). Then tighten down the yoke screw (see Fig. 2b and 2c).
Remove the ﬁnderscope (G) with the attached bracket (F) from its box. Then remove the two knurled thumbscrews from the tele scope’s main body (H). Locate the ﬁnderscope bracket on the telescope’s main body so that the holes drilled in the bracket base line up with those exposed in the telescope’s main body. Reﬁt the two knurled thumbscrews and tighten them down securely (see Fig. 4).
Insert the angle prism (D) into the focusing tube (C). Hold it in place by tightening down the corresponding mounting bolts (see Fig. 5).
Fit the eyepiece (E) into the angle prism (D). The eyepiece also requires adjusting using the small tightening screw (see Fig. 6).

FINDERSCOPE ADJUSTMENT

As the telescope only offers a limited ﬁeld of view, it may be fairly hard to locate a given star or planet for observation. This is why the telescope is ﬁtted with a cross-hair ﬁnderscope for orientation purposes. We recommend performing the following adjustments in daylight.

Insert the eyepiece with the lowest magniﬁcation factor into the angle prism connector. Observe an easily recognizable ﬁxed object that is no more than 300 meters away. Swivel the telescope through its horizontal axis and adjust it along the vertical axis until the object is located right in the center of your ﬁeld of view, then immobilize the telescope by tightening it down securely.
Now look through the ﬁnderscope. If the object seen through the telescope cannot be seen, slacken the adjusting nut and move the ﬁnderscope until you can see the object. Then tighten down the adjusting nut making sure that the object remains visible in the center of the ﬁnderscope. To simplify this procedure, use the adjusting nut to position the object in the center. The ﬁnderscope will move in the direction in which the nut is turned. As soon as the eyepiece adjustment coincides with that of the ﬁnderscope, all of the nuts can be ﬁnally tightened down.

ALTITUDE-AZIMUTH MOUNT

The telescope is ﬁtted with an Altitude-Azimuth mount. “ Altitude ” refers to the telescope’s up and down or vertical movement, while “Azimuth” refers to its sideways or horizontal movement. The Altitude Azimuth mount used in conjunction with the microadjustable Altitude control and Azimuth Lock (N) lets you see the entire night sky or any celestial body without having to move the tripod. Which magniﬁcation should be chosen?

SELECTING A SUITABLE EYEPIECE

The magniﬁcation deﬁnes the telescope’s ability to enlarge an image or to bring it closer in order to see it better.
800 mm focal length Example:
= 40x magniﬁcation
eyepiece focal length 20 mm
The required degree of magniﬁcation depends on the object to be observed.
To this end, we recommend conforming to the following general guidelines:
Ideal viewing conditions are obtained when the magniﬁcation factor corresponds to no more than 15 to 20 times the lens diameter, i.e. the optimal magniﬁcation of 100x to 125x obtained with a 60 mm diameter lens makes it possible to observe most celestial bodies.
We recommend using a lower magniﬁcation factor for observing the stars as the ﬁeld of view will be wider so that the object being observed will be easier to locate. The highest magniﬁcation factor should only be used for especially ﬁnely detailed observations of the moon. This is because the moon is relatively close and exceptionally bright, so that good detail resolution is obtained even with a high magniﬁcation ratio.

GENERAL CONSIDERATIONS

Avoid sudden temperature ﬂuctuations likely to cause any dampness in the air to condense on the telescope’s lens. If this phenomenon occurs, place the lens at a moderate distance away from a heat source and let the dampness evaporate away progressively.
Warning : To avoid any eye injury never look directly into another optical instrument through the telescope and never observe the sun with unprotected eyes!