GINPORD JK1606-2 Electric Foldable Treadmill Instruction Manual

GINPORD JK1606-2 Electric Foldable Treadmill

CAUTION

To avoid injury please read this manual carefully before operating this machine

• For safety purpose, do not stand on running belt while start.
• Please stop immediately if you experience any kind pain, including but not limited to chest pains. nausea, dizziness, or cramp.
• Please speed up slowly if needed.
• Adjustment of belt is prohibited during using.
• It is suggested to wear sports shoes and gym suit while using this equipment.
• Children, the elder, the pregnant, and patients are prohibited from using this treadmill.
• Please clip the safety key on your clothing during using.
• Please firmly hold the handle bars during using .

SAFETY NOTICE

• Please put the treadmill on flat ground. It is unsuitable to put the treadmill at following places:
  1. Outdoors. (The treadmill is specially designed for indoor use only)
  2. Slant ground or slant places on balcony.
  3. Sunlight area or near heater.
  4. Noisy places.
• The proper power for the treadmill is A.C 11 OV.
• Error may appear on display if the power is not stable. Please do not use the same socket together with computer, air conditioner etc.
• It is suggested to wear sports shoes and gym suit while use the treadmill.
• Please speed up or speed down slowly.
• Make sure no child or other object is near while folding or unfolding the treadmill.
• The treadmill should not be located near water or wet object. Error or damage may be caused if water or other liquids drop into the equipment.

CAUTION DURING USE

Keep both the machine and power cord away from heated surfaces.

• If you do not feel well before using, please consult your doctor or coach.
• Please unplug the equipment when not in use.
• Please unplug the tread mi 11 before cleaning, moving or change parts for the tread mi 11.
• Children, the elder and the pregnant are prohibited from using the treadmill. Patients should consult their doctor before starting any exercise routine.
• Please place the treadmill on a level flat surface. There should be 2M of clearance behind the treadmill.
• Do not start the treadmill when it is folded.
• Keep all electrical components, especially motor, power cord and plug, away from water or other liquids.
• Do not wear clothes like long dress, which might catch on any part of the treadmill while using.
• Do not place the treadmill in an area that will block any vent or air openings.
• Do not put any objects on the treadmill.
• Put away the plug from heated place or fire seat.
• Please switch off all functions and unplug after using.
• Do not stand on the belt while you’re preparing to use the treadmill.
• Do not disassemble the treadmill without consulting professional technicians.
• Please make sure the running belt is fastened before using.

TOOLS REQUIRED

• ALLEN WRENCH (PROVIDED)

• SILICONE OIL (PROVIDED)

• SAPNNER (PROVIDED)

• 265 LBS CAPACITY

• 1 PERSON ASSEMBLY

• UP TO 30 MIN ASSEMBLY

HARDWARE

1. Safety Key

2. Round Washer

3. Arc Washers

4. Lock Knob

5. Stretch Knob

6. Short Bolt

7. Pad Support

PRODUCTS MAIN PARTS

1. Cup Holder
2. Console
3. Safety Key
4. Upright Tube
5. Motor Cover
6. Side Rail
7. Running Belt
8. 3-Level Incline
9. End Cap

PARTS

1. HEADER

2. RUNNING DECK

PRODUCT ASSEMBLY

1. Lift the vertical bar of the machine

2. The left and right columns are fixed with flat gaskets, MS, curved gaskets MS and semi-round head hex socket screws M8*16

END CAPS ASSEMBLY

3. First remove the pre-installed screws at the top of the vertical rod, adjust the instrument to the proper position, lock the instrument on the column with the cylindrical head hexagonal screw M625 and the self-locking nut of M6, then turn the instrument, connect the connecting line, adjust the instrument to the level, and then fix the instrument on the column with the curved gasket M8 and the semicircular head hexagonal screw M8 16.

4. Screw on the hold and stretch knobs, plug in the IP AD holder, place the safety lock, and finish assembly

FOLDING UP AND SETTING DOWN

FOLD:

1. Turn off the machine completely.
2. Unscrew the Lock knob (part 4) on the base frame and pull out the stretch knob (part 5).
3. Lift the base frame to the place where the Lock knob (part 4) can put in to fix the base frame .

TECHNICAL SPECIFCATION

CONSOLE INSTRUCTION

1. Connect machine to power, turn on the switch at the front base frame, then press “START” key, the machine will start from 0.5mph/h after 3 seconds. Please make sure the safety key is on the panel before using.

2. During running, press START/STOP key, the machine will be in PAUSE status. Press this key again, the machine will be continue running. Press and hold the key 3 seconds, the machine will. be switched off.

3. Press”+” key for speed up and “-” key for speed down. The fastest speed is 7.5 mph/hand lowest is 0.5mph/h.

4. Press “MODE” key, the screen will show Speed. Time. Calories. And when the SCAN light on, the screen will lights from speed, time, calorie every 5 seconds.

5. Display monitor has 12 programs from P1-P12. While on standby, press “PROG” to set the programs then press “START” to start the machine.

6. While the machine is in use and running, during the auto programs, the(-) and (+) keys are not available. If you want to exit the auto programs, select “STOP” or remove the safety key, and turn on the machine again or place safety key back on. And then you can select desired speed.
   7. For emergency stop, please pull out the sane will stop very slowly Pull out safety key and the screen will show “Err”, put it back and on it will show “OFF”.

7. Press “STOP” key and hold on 3 seconds, the machine will be stopped.

TOTAL 12 PROGRAMS AS BELOW

PROGRAMA
TIME| SET TIME 11.2= RUNNING TIME FOR EACH SECTION
---|---
P01| SPEED| 2| 2| J| 4| 5| J| 4| 5| 5| J| 4| 5| 4| 4| 4| 2| J| 5| J| 2
P02| SPEED| 2| 3| 4| 5| 6| 4| 6| 6| 6| 4| 5| 6| 4| 4| 4| 2| 4| 5| J| 2
P03| SPEED| 2| 4| 4| 6| 6| 4| 7| 7| 7| 4| 7| 7| 4| 4| 4| 2| 5| 3| J| 2
P04| SPEED| 2| 5| 5| 6| 6| 6| 6| 4| 4| 2| 2| 4| 7| 6| 6| 6| 6| 6| 4| 2
P05| SPEED| J| J| 5| 1| 6| 6| 7.5| 5| 5| 7.5| 7.5| 5| 6| 5| 7.5| 5| 1| 5| 4| J
P06| SPEED| 3| 7.5| 7.5| 1| 7.5| 6| 7.5| 6| 4| 2| 5| 4| 1| 6| 6| 6| 7.5| 6| 4| J
P07| SPEED| J| 4| 6| 6| 7. 5| 6| 7.5| 1| 5| 6| 6| 6| 6| 1| 7.5| 1| 6| 6| 5| J
P0B| SPEED| J| 5| 6| 1| 7.5| 7.5| 1| 7.5| 4| 1| 1| 4| 1| 1| 7.5| 1| 7.5| 1| 5| J
P09| SPEED| 4| 1| 3| 1| 1| 1| 7.5| 7.5| 5| 7.5| 6| 1| 6| 1| 7.5| 7.5| 1| 1| 5| J
P10| SPEED| 4| 5| J| 7.5| 7.5| 7.5| 7.5| 7.5| 4| 7.5| 5| 4| 1| 7.5| 1| 1| 7.5| 1| 6| 4
P11| SPEED| 4| 7.5| 6| 7.5| 1| 6| 6| 7.5| 5| 7.5| 7.5| 6| 6| 6| 6| 6| 7| 7.5| 7.5| 2
P12| SPEED| 4| 4| 1| 7.5| 2| 7.5| 7.5| 7.5| 7.5| 7.5| 7.5| 7.5| 1| 7.5| 7.5| 2| 7.5| 7.5| 7.5| 2

USAGE OF SILICONE OIL

1. Before you start the treadmill, please lubricate the running belt first. Pull up the running belt slightly, apply silicone oil to the backside of the belt and the top surface of the running deck.
2. Start the treadmill and keep it running for 3 minutes so that the oil spread and even out.
   It is necessary to maintain your treadmill every 30 working hours of the treadmill for optimal performance, which also helps extend the service life of parts.

DAILY MAINTAINANCE

1. Please disconnect power before checking the machine or cleaning.
2. Clear belt and dial plate after use, at least once a week.
3. Check and tighten screws and spines at fixing point.
4. Do not hang clothes or other objects on the machine.

RUNNING BELT ADJUSTMENT

After installation video tutorial

RUNNING BELT DEVIATE TO LEFT

1. Start the machine by speed at 1.2-1.Bumpy without loading, use Allen wrench to turn the screw 1/4 circle clockwise (seefig1 ).

2. Then make the machine running without loading 1-2 minutes. Please adjust like this to make the belt till to mid place.

RUNNING BELT DEVIATE TO RIGHT

1. Start the machine by speed at 1.2-1.Bmph without loading, use Allen wrench to turn the screw 1/4 circle clockwise (seefig2).

2. Then make the machine running without loading 1-2 minutes. Please adjust like this to make the belt till to mid place.

RUNNING BELT LOGJAM

1. If the running belt is in dead condition, use Allen wrench to make the screw 1/2 circle both left and right till this logjam solved.

EXERCISE GULDE

PLEASE NOTE: Before beginning any exercise program, consult your physician.
This is important especially if you are over the age of 45 or individuals with pre-existing health problem.

The pulse sensors are not medical devices. Various factors, including the user’s movement, may affect the accuracy of heart rate readings. The pulse sensors are intended only as an exercise aid in determining heart rate trends in general.

Exercising is great way to control your weight, improving your fitness and reduce the effect of aging and stress.
The key to success is to make exercise a regular and enjoyable part of your everyday life.

The condition of your heart and lungs and how efficient they are in delivering oxygen via your blood to your muscles is an important factor to your fitness. Your muscles use this oxygen to provide enough energy for daily activity. This is called aerobic activity. When you are fit, your heart will not have to work so hard. It will pump a lot fewer times per minute, reducing the wear and tear of your heart. So, as you can see, the fitter you are, the healthier and greater you will feel.

Warm-up

• Start each workout with 5 to 10 minutes of stretching and some light exercises. A proper warm-up Increase your body temperature, heart rate and circulation in preparation for exercise. Easy into your exercise.

Training Zone Exercise

• After warming up, increase the intensity to your desired exercise program. Be sure to maintain your Intensity for maximum performance. Breathe regularly and deeply as you exercise-never hold you breathe.

Cool Down

• Finish each workout with a light jog or walk for at least 1 minute. Then complete 5 to 10 minutes of stretching to cool down. This will increase the flexibility of your muscles and will help prevent post- exercise problems.

HEART RATE

THIS IS HOW YOUR PULSE SHOULD BEHAVE DURING GENERAL FITNESS

EXERCISE. REMEMBER TO WARM UP AND COOL DOWN FOR A FEW MINUTES
The most important factor here is the amount of effort you put in. The harder and longer you work the more calories you will burn. Effectively this is the same as if you were training to improve your fitness, the difference is the goal.

TROUBLE SHOOTING

1. Put safety key in the yellow area of panel
2. Err (or EOO) still shows or there is no function, change the computer screen/display monitor.

E2| Control Board Error| Control board is broken or pseudo soldering on control board| Replace control board
E4| Control Board Error| Control board is broken| Replace control board
ES| Overcurrent Protection| Control board short circuit or motor blocked|

1. Open the motor cover and check whether the motor is blocked. Remove the block if yes
2. Replace the control board if it’s not blocked, or the error sti11 shows.

E6| Motor Error| Mo tor broken or motor line fall off|

1. Open the motor cover and check whether the motor is broken or whether the motor wire is connected to control board properly Reconnect the wire is recommended.
2. Replace the control board if the error still shows.

E7| Communication Failures| Wires from the control board to panel board are broken or not properly connected|

1. Make sure the wires from the control board and panel board are connected securely and not damaged.
2. Replace the control board if the error still shows.

ES| Overload Protection| Excess of electricity or user exceeded max load weight|

1. Make sure the user does not exceed max weight capacity.
2. Reconnect power and re-start the machine.
3. Replace the control board if the error code till shows.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>