amazon basics B08J4J478Z Contemporary Single Cylinder Door Handleset with Stamford Lever Instruction Manual
- June 16, 2024
- amazon basics
Table of Contents
B08J4J478Z Contemporary Single Cylinder Door Handleset with Stamford Lever
Instruction Manual
Contemporary Single Cylinder Door Handleset with Stamford Lever
Product Description
1.1 Deadbolt lock
| A | Key |
|---|---|
| B | Cylinder |
| C | Exterior chassis |
| D | Latch |
| E | Latch face plate x2 |
| F | Drive-in collar |
| G | Screw x4 |
| H | Strike plate |
| I | Mounting plate |
| J | Bolt x2 |
| K | nterior chassis* |
| L | Washer* x2 (flat and |
| M | Turn piece* |
| N | Set screw* |
| O | Hex key |
Door handleset
| P | Exterior lever |
|---|---|
| Q | Washer |
| R | Bottom bolt |
| S | Latch |
| T | Latch face plate x2 |
| U | Drive-in collar |
| V | Screw x4 |
| W | Strike plate |
| X | nterior lever |
| Y | Bolt x2 |
Installation
NOTICE
This product is classified as “full indoor type” and should only be installed
in indoor environment.
NOTICE
Determine the door handing before installing the product.
Face the door from the exterior side:
- If the hinges are installed on the left, the door is left-handed.
- If the hinges are installed on the right, the door is right-handed.
NOTICE
- Prepare all the tools required for the installation.
- Follow the steps n chapter “Instructions for doors with existing holes” at the back of the manual to install the deadbolt lock (P. 18-27) and door handleset (P. 28-35). For drilling, read chapter “Drilling instructions” (P. 36-44).
- Illustrations in the steps in chapter “Instructions for doors with existing holes” and “Drilling instructions” are for left-handed doors. Reverse the lever position for right-handed doors.
Instructions for doors with existing holes
Drilling instructions
Confirm that the hole in door
edge is 01″ (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″ (45
mm) thick. Also confirm that the hole in the door is 02-1 /8″ (54 mm).
Hold the latch (D) with the latch face flush against
the door edge. Ensure that the slot is centered n the door hole. Adjust the
latch f needed. 
Optional – for doors with
chiseled pocket: pry open the attached latch face plate (E} and replace it
with the rectangular one. 
Optional – for doors without
chiseled pocket: pry open the face plate holder with a flat-head screwdriver.
Attach the drive-in collar (F) to the latch. 
For
latch with face plate {E): fit the latch into the hole and secure with two
screws {G). I For latch with drive-in collar {F): insert the latch with drive-
in collar and tap into position using a wood block and hammer. 
Mount the exterior chassis (C) on the door. The torque blade of the
cylinder (B) must pass through the slot on the latch (D).
Pass the mounting plate (I) through the torque blade and fix it with
two bolts (J).
Detach the turn piece (M) from
the interior chassis (K) using the hex key (0). Carefully keep the removed
washers (L) and set screw (N). 
Fit the interior chassis (K)
onto the mounting plate (I) with the pin passing through. Place the washers
(L) onto the pin and secure the turn piece (M) n place by tightening the set
screw (N). 
Ensure that the door frame hole
s at least 1″ (25 mm) deep. Mount the strike plate (H) on the door frame with
two screws (G). 
Confirm that the hole in door
edge is 01″ (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″ (45
mm) thick. Also confirm that the hole in the door is 02-1 /8″ (54 mm).
Hold the latch (S) with the latch face flush against
the door edge. Ensure that the square hole s centered in the door hole. Adjust
the latch if needed. 
Optional – for doors with chiseled pocket: pry open the attached latch face
plate (T} and replace it with the rectangular one. 
Optional – for doors without chiseled pocket: pry open the attached latch face
plate (T). Remove the face plate holder and attach the drive-in collar (U).
Latch with face plate (T}: fit it into the hole and
secure with two screws (V}. I Latch with drive-in collar (U}: insert it and
tap into position using a wood block and hammer. Latch bolt bevel must face to
closing direction.
Mount the exterior lever (P} on
the door with the washer (Q} and bottom bolt (R}. The middle bolt of the lever
must pass through the slot on the latch (S}. 
Mount the interior lever (X) on the door with two bolts (Y).
Ensure that the door frame hole is at least 1″ (25 mm) deep. Mount
the strike plate (W) on the door frame with two screws (V). 2Use template to
mark holes on door. Fold template along fold line and place it along the door
edge. Select the drilling point for different door thickness: 1-3/8″ (35 mm),
1-9/16″ (40 mm) or 1-3/4″ (45 mm).
Drill the pairs of holes using chisel and circular drill bits.
NOTICE Drill from one side until the drill just breaks through, then
complete hole from the other side to prevent wood from splintering.
Place the template on the door aligning the hole marking with the
door hole. Mark the bottom screw hole on door.
Drill a hole on the marked position using 03/8″ (10 mm) drill
bit.
Mark the outline of the face plate (E, T). Chisel
5/32″ (4 mm) deep for the face plate (E) and 1 /8″ (3 mm) deep for the face
plate (T)
Mark the positions of the screw
holes. Drill two 1″ (25 mm) deep holes using 1/8″ (3 mm) drill bit. 
Close the door and mark the op and bottom position of the latch
across the door frame. Open the door and measure the distance X from the
exterior door edge to the flat end of the latch.
Mark a vertical line on the door frame for the measured distance X
from the outside to the inside. Position the strike plate (H, W) within the
guidelines. Mark and drill two 1″ (25 mm) deep screw holes using 1/8″ (3 mm)
drill bit.
Mark and drill a 01″ (25.4 mm)
hole with 1″ (25 mm) depth at ntersection of horizontal and vertical line of
the cutout of the strike plate (H, W).
Chisel 5/64″ (2 mm) deep for the strike plate (H)
and 1 /16″ (1.6 mm) deep for the strike plate (W).
amazon.com/AmazonBasics
MADE IN TAIWAN
V03-10/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>