AIKVSXER 6PACK LED Flat Panel Light User Manual

AIKVSXER 6PACK LED Flat Panel Light

LED Flat Panel Light User Manual

Specifications

• Product description: Dimmable lightweight LED Panel Light
• Color options: 3000K, 4000K, 5000K
• Brightness adjustment: 10% – 100%
• Dimmer compatibility: Triac dimmer (not included)
• Sizes available: 2x2FT, 0.5x4FT, 1x4FT, 2x4FT

Accessories List

surface
Expansion screws PWA435| Picture| 6 pcs| For fastening the fixture to the concrete wall
Silicone cap KA3.550| Picture| 6 pcs| For covering the screw holes
Wire nut| Picture| 2 pcs| For connecting wires
Double sided tape| Picture| 4 pcs| For fixing the positioning tool

Product Usage Instructions

A. Install on the surface of the wooden ceiling or wooden wall
WARNING: Turn off power at fuse or circuit breaker before installing.

1. Fix the location tool to the installation position with double-sided tape.
2. Remove the location tool after marking the hole as shown on the location tool.
3. Install the hanging rope kit as shown in the picture.
4. Hang the fixture on the hanging rope kit.
5. Connect wires:
   • Wires of the same color are joined together.
   • Color of wires: L-Black, N-White, PE-Green.
   • Black to Black, White to White, Green to Green.
6. Fix the fixture to the remaining four holes with screws and expansion screws.
7. Finally, cover the screw holes with silicone cap.

B. Install on the surface of the cavity surface
WARNING: Turn off power at fuse or circuit breaker before installing.

1. Fix the location tool to the installation position with double-sided tape.
2. Remove the location tool after marking the hole as shown on the location tool.
3. Drill a hole at No. 1, 2, 3, 4 with an electric drill using a 12 mm bit until it penetrates the empty layer (No. 5, 6 is a 6 mm bit).
4. Install the hanging rope kit as shown in the picture.
5. Hang the fixture on the hanging rope kit.
6. Wiring:
   • Wires of the same color are joined together (black to black, white to white, green to green).
7. Press down on the spring clamp and push it through holes 1, 2, 3, and 4.
8. Tighten the screw and cover the screw holes with silicone cap.

C. Install on the surface of the concrete surface

1. Fix the location tool to the installation position with double-sided tape.
2. Remove the location tool after marking the hole as shown on the location tool.
3. Use an electric drill with a 6 mm drill bit to drill holes in 1, 2, 3, 4, 5, 6. The drill holes should have a depth not less than 65mm.

FAQ

1. Q: What is the compatibility of the dimmer?
   A: The dimmable LED Panel Light is compatible with a triac dimmer. However, the dimmer is not included with the product.

2. Q: How many color options are available?
   A: The LED Panel Light offers 3 color options: 3000K, 4000K, and 5000K.

3. Q: What sizes are available for the LED Panel Light?
   A: The LED Panel Light is available in the following sizes: 2x2FT, 0.5x4FT, 1x4FT, and 2x4FT.

4. Q: What is the after-sales service email?
   A: For any after-sales service inquiries, please contact inquire@ainexter.com.

LED Flat Panel Light User Manual

Product description

Easily replace outdated tubes and fixtures with this dimmable lightweight LED Panel Light. Optimize focus and productivity in your space by changing 3 color 3000K/4000K/5000K and adjusting 10%-100% brightness with triac dimmer. (dimmer not included) After-sales service email: inquire@ainexter.com

Accessories list

A. Install on the surface of the wooden ceiling or wooden wall
WARNING: Turn off power at fuse or circuit breaker before installing.

1. Fix the location tool to the installation position with double-sided tape.
2. Remove the location tool after marking the hole as shown on the location tool.
3. Install the hanging rope kit as shown in the picture above.
4. Hang the fixture on the hanging rope kit as above.
5. Wiring Wires of the same color are joined together Color of wires: L-Black, N-White, PE-Green B lack to Black, White to White, Green to Green.
6. Fix the fixture to the remaining four holes with screws and expansion screws. Finally, cover the screw holes with silicone cap.

B. Install on the surface of the cavity surface
WARNING: Turn off power at fuse or circuit breaker before installing.

1. Fix the location tool to the installation position with double-sided tape.
2. Remove the location tool after marking the hole as shown on the location tool.
3. Drill a hole at No. 1.2.3.4 with an electric drill with a 12 mm bit until it penetrates the empty layer (No. 5.6 is a 6 mm bit).
4. Install the hanging rope kit as shown in the picture above.
5. Hang the fixture on the hanging rope kit as shown in the picture above.
6. Wiring wires of the same color are joined together (black to black, white to white, green to green).
7. Find 4pcs 90cm screws, pass them through the mounting hole on the front of the fixture, and screw the spring clamp to one end of the screw (as shown).
8. Press down on the spring clamp as shown and push it through holes 1, 2, 3 and 4.
9. Tighten the screw, cover the screw holes with silicone cap.

C. Install on the surface of the concrete surface

1. Fix the location tool to the installation position with double-sided tape
2. Remove the location tool after marking the hole as shown on the location tool
3. Use an electric drill with 6 mm drill bit to drill holes in 1.2.3.4.5.6 The drill holes at the fixed position with depth not less than 65mm
4. Tap the expansion screw into the hole as shown.
5. Install the hanging rope kit as shown in the picture above.
6. Hang the fixture on the hanging rope kit as shown in the picture above
7. Wiring Wires of the same color are joined together (black to black, white to white, green to green).
8. Fix the fixture to the remaining four holes with screws and expansion screws. Finally, cover the screw holes with silicone cap.

WARNING -To reduce the risk of fire, electric shock, or physical injury:

• The led flat panel light only supports 120V 60Hz voltage to ensure that all functions can be used
• This product should be installed by a person familiar with the construction and operation of the product and the hazards involved. Safety eyeglasses and gloves are recommended.
• Check for shipping damage before installing. If the product is damaged, do not use it.
• Turn off the switch and circuit breaker before installing this fixture.
• Proper grounding is required to ensure safety.
• Clean the fixture regularly to ensure proper operation. Do not clean with harsh solvents.
• Use safety precautions and abide by regional and local laws or regulations

Q&A (Important)

How to change the color temperature？

• Q: I can’t find a toggle on the light; how can I select color temperature from 3000/4000/5000k?
  A: You can change color temperature by flicking the wall switch on and off within 5s.

How to keep all the lights in same color?

• Q: How to get multiple lights back in sync if one light is out of sync with the others?
  A: You can reset all the lights to the same color by turning the wall switch on and off 3 times in a row within
  1 second.

How to remember the color?

• Q: How to make the light remember the last color temperature when I turn it on again?
  A: Turn on the light more than 8 seconds after turning off the light to reproduce the last color temperature. (If you turn off the light and turn it on again within 8 seconds, the color temperature will change)

0.5×4 FT/1×4 FT/2×2 FT/2×4 FT LED Flat Panel Light Specifications

3000K/4000K/5000K
Life Span| 50,000H| 50,000H| 50,000H| 50,000H
CRI| 90| 90| 90| 90
Material| Aluminum alloy| Aluminum alloy| Aluminum alloy| Aluminum alloy
Warranty| 5 years| 5 years| 5 years| 5 years

Recommended Dimmer Models
Compatible with triac dimmer but not include in the package, please buy triac dimmer separately

Triac dimer change 3 color and 10%-100% brightness, if you don’t need to change brightness, use a regular switch can   change 3 color as well.

Instruction about color changing function (Important)

How to change color?
You can change color by flipping the wall switch on and off within 5 seconds. (3000k) turn off->within 5s ->turn on (4000k) ->turn off->within 5s ->turn on(5000k)

How to fix color?
This light has a memory function, after you turn off the light, and last for at least 10 seconds, then turn it on again, it will reproduce the last color temperature. For example: The color temperature was 4000k before the light was turned off yesterday, The next time when you turn on the light again, they will keep 4000k. This light remembers the most commonly used color temperature, so you do not need to adjust the color temperature frequently in your daily life.

How to make all lights in 1 color?
If the color of some lights is out of sync with the others, you can reset the color of all the lights to the same color by turning the wall switch on and off 3 times in a row within 1 second.

After-Sales Service

• Dear Customer, Thank you so much for your support on led flat panel light.
• Your order made our day, we hope we make yours. We are committed to providing the best products and services to our customers. If you have any questions about the order, please feel free to contact us.
• If you have any questions about the order, please feel free to contact us. We will keep online and will try our best to solve the problem for you as soon as possible. Thank you!
•  inquire@ainexter.com

After-sales Service Process

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>