Sintai AOFN210 WiFi Module Installation Guide
- June 16, 2024
- Sintai
Table of Contents
Model:
AOFN210
‘WLAN Module
WLAN 802.11 b/g/n SDIO
Quick Installation Guide
Functional Specification
| Standard | IEEE 802.11b/g/n |
|---|---|
| Radio Technology | 802.11 b /DSSS, 802.11g, 802.11 n /OFDM |
| Modulation Type | DSSS with DBPSK.DQPSK,CCK |
OFDM with BPSK, QPSK,16QAM,64QAM
Transfer rate| 802.11 b: up to 11Mbps 802.11g: up to 54Mbps 802.11n: up to
150Mbps
Frequency Range| 2400MHz – 2500MHz
Operating Channel| Ch.1 – 11
Operating Voltage| 3.3Vdc ±10% I/O supply voltage from host
Operating Temperature| +0 – 70°C
Antenna Information
Brand Name| Part No.| Antenna Gain| Frequency
range| Antenna
Type| Connector| Note
---|---|---|---|---|---|---
ELECTRIC
CONNECTOR
TECHNOLOGY| 81800V576| -1.39 dBi| 2.4GHz-2.5GHz| FPC| I-PEX| Original
Shenzhen
Fbetter
Electronic| S2B4BC3F1B04000| -0.98 dBi| 2.4GHz-2.5GHz| FPC| I-PEX| Original
| | | | | |
| | | | | |
| | | | | |
| | | | | |
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This device and its antenna(s) must not be co-located with any other
transmitters except in accordance with FCC multi-transmitter product
procedures.
Referring to the multi-transmitter policy, multiple-transmitter(s) and
module(s) can be operated simultaneously without C2PC.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This module is intended only for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna.
- For all products market in US, OEM has to limit the operation channels in CHI to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed
The OEM integrators must use the equivalent antennas or C2PC will be required.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then
the FCC authorization is no longer considered valid and the FCC ID can not be
used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
This module is intended for OEM integrator. This module is only FCC authorized
for the specific rule parts listed on the grant, and that the host product
manufacturer is responsible for compliance to any other FCC rules that apply
to the host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed.
Additional testing and certification may be necessary when multiple modules
are used.
The host manufacturer should reference KDB Publication 996369 D04 Module
Integration Guide.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following: “Contains FCC ID: SERAOFN210″. The grantee’s FCC ID can be used
only when all FCC compliance requirements are met.
This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
In the users manual of the end product, the end user has to be informed to
keep at least 20cm separation with the antenna while this end product is
installed and operated. The end user has to be informed that the FCC radio-
frequency exposure guidelines for an uncontrolled environment can be
satisfied.
The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user’s authority to
operate this equipment.
This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Contact Information
Company name: Sintai Optical (Shenzhen) Co., Ltd.
Qiwei Ind Sec, 1st,2nd,&3Rd Bldg, Lisonglang Village Gongming
Company address-
Town,Bao an District,
Contact Name: Qian Yang
E-Mail: gian.yang@sintai.com
Tel: +86-769-85535435
Fax: +86-755-29168341
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>